共查询到17条相似文献,搜索用时 93 毫秒
1.
PXI总线是美国国家仪器公司于1997年9月1日发布的一种全新的、开放的模块化仪器标准总线.PCI 9030是PLX技术公司开发的PCI总线目标模块专用接口芯片,它完全符合PCI 2.2版规范,是业界首个支持CompactPCI热拔插的目标设备具有许多先进的特性.本文介绍其功能、特点,提出了采用PCI 9030+CPLD设计PXI总线接口电路的方法,应用PCI 9030完成基本的PCI总线接口,利用CPLD的可编程功能完成PXI总线接口逻辑控制.最后给出了在PXI总线开关模块中的应用实例. 相似文献
2.
3.
4.
介绍在FPGA上实现PCI总线接口的设计方案,在主控与用户功能模块之间的进行数据交换,以突发写方式进行大量数据的高速传输.重点描述用户逻辑接口模块的程序设计,满足PCI总线时序要求,提高系统效率和性能. 相似文献
5.
本文介绍了PXI总线D/A模块的设计.该模块具有四通道可程控的直流电压和直流电流的选择输出.根据PXI总线规范,本模块采用PCI总线专用接口芯片9030和EPLD技术来完成PXI总线接口电路设计以及模块功能电路的具体实施方案. 相似文献
6.
7.
通用PCI扩展卡是一种自行研制的高速数据采集卡,可以根据用户的要求将各种数字信号以大于40MHZ的采集速率通过PCI接口采集入计算机,是一种计算机对外的高速硬件接口。具有很广泛的实际应用价值。 相似文献
8.
基于 PCI 总线的接口设计通过 PCI 接口控制芯片 S5933, 双端口 RAM 和可编程逻辑器件实现主机同各外围设备间的数据交换。用户应用程序调用利用 WinDriver 编程的设备驱动程序提供的各函数接口来操作硬件。 相似文献
9.
10.
CAN总线温度控制器是一个典型的检测、控制型应用系统,它要求系统完成从温度检测、信号处理、输入输出接口电路设计对温度进行控制。本文通过分析CAN总线温度控制器,温度传感器电路,A/D模数转换电路,D/A数模转换电路,并以8031单片机为核心,对整体电路进行设计。 相似文献
11.
讨论了一种关于音频调理的方法,由于该系统对传输要求比较高,所以系统的传输速度和效率都是很重要的性能指标,在系统的性能指标基础上,选定了PCI总线接口的方案,为简化电路,论文采用PLX公司的PCI9054芯片实现PCI接口,用FPGA实现FIFO数据缓存和本地总线控制逻辑,使通过音频处理后的声音信号通过声音编解码器出去。最后编写了该系统的驱动程序以及应用程序,达到了预期效果。 相似文献
12.
Preethichandra D.M.G. Shida K. 《IEEE transactions on instrumentation and measurement》2001,50(6):1583-1586
This paper presents an easy-to-design interface circuit to measure very small-percentage capacitance variations in capacitive sensors, especially suitable for industrial measurements. A computer-controlled 24-bit A/D converter is employed to obtain a higher resolution. This interface circuit can be used with various types of capacitive sensors. The most interesting thing is, that the measurement results through this interface circuit are independent of the initial capacitance of the sensor. In addition, the double differential operating principle used here minimizes the error caused by coupling and stray capacitance of sensor probes. The operating principle of the designed interface circuit, the major assumptions made, test data, and possible future developments are discussed 相似文献
13.
针对现有盾构管片拼装设备低精度、低效率、低可靠性的问题,以实现管片高效拼装为核心目标,设计了管片拼装试验台监控系统.在全面分析了管片拼装试验台的原理及监控需求的基础上,首先设计了以工控机为控制核心及以PCI数据采集控制卡为输入和输出模块的数据采集控制系统,接着分别设计了以软起动器为启停控制设备的动力电机电器控制线路及采用直接启动方式的风冷器电器控制线路,继而基于LabVIEW开发了可实现高速数据采集及实时控制的试验台监控系统软件,最后依据相关设计搭建了管片拼装试验台监控系统. 监控系统运行结果表明,硬件运算高速、可靠,软件设计合理、有效,该系统在试验台的操作过程及管片高效拼装方法的研究过程中发挥了重要作用. 相似文献
14.
15.
介绍了一种基于PCI总线的高速数据采集传输系统的实现方法。概述了快速、简易PCI总线控制专用芯片CH365的主要特点,描述了其本地硬件地址的实现方法,并给出了在12通道数据采集系统中的一个应用实例。 相似文献
16.
17.
Nihtianov S.N. Shterev G.P. Petrov N. Meijer G.C.M. 《IEEE transactions on instrumentation and measurement》2001,50(4):976-980
In this paper, we present a simple interface circuit for measuring impedance based on a second-order harmonic oscillator. The circuit is intended for testing the sterility of aseptically packed food products, where it must measure the conductivity changes of the packaged food in a nondestructive way. The measured impedance is modeled as a low-ohmic resistor (representing the conductivity of the food) in series with a capacitor (the walls of the food container). The oscillator is built with fast current-feedback operational amplifiers (CFOA). To measure the resistive component of the impedance, an AC-to-DC converter is realized with a wide frequency range analog multiplier. The presented experimental results prove that with this interface circuit an accurate measurement of the impedance components can be achieved in a frequency range up to 10 MHz. The range of the resistive component is from a few ohms up to 200 ohms; the range of the capacitive component is from 50 pF up to 300 pF 相似文献