The measurement of the adhesion force between ceramic particles and metal matrix in ceramic reinforced-metal matrix composites

This paper presents the method for measurement of the adhesion force and fracture strength of the interface between ceramic particles and metal matrix in ceramic reinforced-metal matrix composites. Three samples with the following Cu to Al₂O₃ ratio (in vol.%) were prepared: 98.0Cu/2.0Al₂O₃, 95.0Cu/5.0Al₂O₃ and 90Cu/10Al₂O₃. Furthermore, microwires which contain a few ceramic particles were produced by means of electro etching. The microwires with clearly exposed interface were tested with use of the microtensile tester. The microwires usually break exactly at the interface between the metal matrix and ceramic particle. The force and the interface area were carefully measured and then the fracture strength of the interface was determined. The strength of the interface between ceramic particle and metal matrix was equal to 59 ± 8 MPa and 59 ± 11 MPa in the case of 2% and 5% Al₂O₃ to Cu ratio, respectively. On the other hand, it was significantly lower (38 ± 5 MPa) for the wires made of composite with 10% Al₂O₃.     

Tensile properties of in situ synthesized (TiB + La2O3)/β-Ti composite

A novel (TiB + La₂O₃)/Ti-alloy composite was In situ synthesized through homogeneously melting in a non-consumable vacuum arc remelting furnace. Ti–35Nb–2Ta–3Zr β titanium alloy was chosen as the matrix Ti-alloy and different mass fractions of LaB₆ were chosen as additions. Microstructure observations were examined by optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscopy (TEM). The phase analysis was identified by X-ray diffraction (XRD). Largest ultimate tensile strength around 580 MPa and highest elongation around 30% is obtained in 0.1% LaB₆-additioned specimen. The appearance of too many La₂O₃ particles and the reduction of oxygen in the matrix alloy also attribute much to the strength and plasticity of (TiB + La₂O₃)/Ti composites. Lower ultimate tensile strength around 526 MPa is obtained in 0.5% LaB₆-additioned specimen.     

Low-temperature diffusion brazing of actively metallized Al2O3 ceramic tube and 5A05 aluminum alloy

A low-temperature ceramic–metal joining technique was successfully developed to produce a vacuum-tight Al₂O₃ ceramic and 5A05 aluminum alloy joint, with leak rates of less than 1.0 × 10^− 9 Pa∙m³/s. This involved two steps: active metallization of the Al₂O₃ ceramic surface using Ag–Cu–TiH₂–B composite filler, followed by diffusion brazing of metallized Al₂O₃ ceramic and 5A05 alloy at 530 °C. The microstructure, interfacial reactions and mechanical properties of the actively metallized Al₂O₃ ceramic and diffusion-brazed Al₂O₃/5A05 joint were investigated. The joint properties were determined by the formation of a continuous Ti₃Cu₃O reaction layer adjacent to Al₂O₃ ceramic, in situ synthesized TiB whiskers in the brazing seam, and dissolution thickness of 5A05 alloy. The maximum shear strength of the bonded joints reached 70 MPa, while fracture propagated in the Al₂O₃ substrate, with a bowed crack path. A model for quantitatively evaluating the dissolution thickness of 5A05 aluminum alloy during diffusion brazing process was established.     

Improvement of high-temperature oxidation resistance and strength in alumina-forming austenitic stainless steels

A new alumina-forming austenitic stainless steel with greatly improved high-temperature oxidation resistance and strength was developed via alloying 3.0 wt.% Al in the Fe-25Ni-18Cr based alloy. Continuous, stable and exclusive alumina scale was formed in either dry air or air with 10% water vapor mixed environment at 800 °C. The long-term high-temperature oxidation performance is appreciably enhanced which is associated with the high density of the B2-NiAl precipitation phase maintaining the Al₂O₃ surface layer. Moreover, when tested at 750 °C in dry air environment, the new steel showed high yield and fracture tensile strength of 310–335 and 480–500 MPa, respectively.     

In situ TiB2 particulate reinforced near eutectic Al–Si alloy composites

In situ TiB₂ particulate reinforced near eutectic Al–Si alloy composites fabricated by the melt reaction composing (MRC) methods have been investigated. It has been shown that minute TiB₂ particles (less than 1 μm) uniformly distribute in the eutectic structure and they are interlaced with the coralline-like eutectic Si, while there are very few TiB₂ particles in α-Al. It has been also shown that in situ TiB₂ particles can enhance the tensile strength of the Al–Si alloy matrix. The strengthening effect increases with increasing TiB₂ content. The ultimate tensile strength (UTS) at room temperature of as-cast 6%TiB₂/Al–Si–Mg composite is 296 MPa, that is a 14.7% increase over the matrix, and its elongation at fracture is 5.5%. After heat-treatment (T6), the UTS of the composites reaches 384 MPa. The strengthening mechanism has been discussed.     

Effects of Si addition on microstructure and mechanical properties of Mg–8Gd–4Y–Nd–Zr alloy

Effects of Si addition (1.0 wt.%) on microstructure and mechanical properties of Mg–8Gd–4Y–Nd–Zr alloy have been investigated using scanning electron microscopy (SEM) equipped with energy dispersive spectrum (EDS), X-ray diffraction (XRD), hardness measurements and tensile testing. The results indicated that the addition of Si led to the formation of Mg₂Si and (RE + Si)-rich particles, which enhanced the Young’s modulus of the alloy by 7 GPa while decreased the yield strength and ultimate strength by 10 MPa and 31 MPa, respectively. The tensile properties of the Mg–8Gd–4Y–Nd–Zr–Si alloy are as follows: Young’s modulus E = 51 GPa, yield strength σ_0.2 = 347 MPa, ultimate strength σ_b = 392 MPa and elongation δ = 2.7%. The increase in Young’s modulus was attributed to the formation of particles with high Young’s modulus, while the decrease in strength was ascribed to the decrease in volume fraction of metastable β′ precipitates caused by the consumption of rare earth atoms due to the formation of the rare earth containing particles.     

Evaluation of microstructure and mechanical properties of Al/Al2O3/SiC hybrid composite fabricated by accumulative roll bonding process

In this investigation, a new kind of metal matrix composites with a matrix of pure aluminum and hybrid reinforcement of Al₂O₃ and SiC particles was fabricated for the first time by anodizing followed by eight cycles accumulative roll bonding (ARB). The resulting microstructures and the corresponding mechanical properties of composites within different stages of ARB process were studied. It was found that with increasing the ARB cycles, alumina layers were fractured, resulting in homogenous distribution of Al₂O₃ particles in the aluminum matrix. Also, the distribution of SiC particles was improved and the porosity between particles and the matrix was decreased. It was observed that the tensile strength of composites improved by increasing the ARB passes, i.e. the tensile strength of the Al/1.6 vol.% Al₂O₃/1 vol.% SiC composite was measured to be about 3.1 times higher than as-received material. In addition, tensile strength of composites decreased by increasing volume fraction of SiC particles to more than 1 vol.%. Scanning electron microscopy (SEM) observation of fractured surfaces showed that the failure mechanism of broken hybrid composite was shear ductile rupture.     

SiC nanoparticle-reinforced Al2O3–Nb composite as a potential femoral head material in total hip arthroplasty

A ceramic–metal composite consisting of SiC nanoparticle-reinforced Al₂O₃ and Nb (referred to as SiC/Al₂O₃–Nb), was prepared and evaluated in vitro for potential application as a femoral head material in total hip arthroplasty. Dense bi-layer laminates of SiC nanoparticle-reinforced Al₂O₃ and Nb were fabricated by hot pressing of powders (1425 °C; 35 MPa), and evaluated using scanning electron microscopy, microchemical analysis, and mechanical testing. The flexural strength of the SiC/Al₂O₃–Nb laminate (960 ± 20 MPa) was higher than the value (720 ± 40 MPa) for an Al₂O₃–Nb laminate, and far higher than the value (620 ± 50 MPa) for SiC nanoparticle-reinforced Al₂O₃ (SiC/Al₂O₃). The Vickers hardness of SiC/Al₂O₃ was 17 ± 2 GPa, compared to 12 ± 1 GPa for Al₂O₃. A high interfacial shear strength of the SiC/Al₂O₃–Nb laminate (310 ± 100 MPa), coupled with SEM observation of the interfacial region, showed strong bonding between the SiC/Al₂O₃ and Nb layers. Composite femoral heads consisting of a SiC/Al₂O₃ surface layer and a Nb core could potentially lead to a reduction in the tendency for brittle failure as well as to lower wear, when compared to Al₂O₃ femoral heads.     

Al2O3–FeCrAl composites and functionally graded materials fabricated by reactive hot pressing

Al₂O₃–FeCrAl composites were fabricated by mixing Fe₂O₃, Al and Cr powders and then reactive hot pressing. The high temperature alloy FeCrAl was formed by the reaction of extra Al, Cr and the Fe reduced from Fe₂O₃. The Al₂O₃–FeCrAl composites with various Al₂O₃ fractions were successfully fabricated by the proper addition of extra Fe, Cr, Al or Al₂O₃ powders. A five-layer functionally graded material of YSZ–FeCrAl was fabricated using the Al₂O₃–FeCrAl composites with compositions of 25, 53.2 and 75 vol.% Al₂O₃ as interlayer. The results from XRD analysis, optical microscope observation and thermal cycling test show that the composites fabricated by this method consist of α-Al₂O₃ phase and (Fe, Cr, Al) solid solution. The α-Al₂O₃ grain formed by this in-situ reaction between Fe₂O₃ and Fe is ultrafine and uniform distribution. The three-point bending strength is 305.0 MPa for the composite with 53.2 vol.% Al₂O₃ prepared by the reactive hot pressing, about 20% higher than that of the composite with same composition prepared by ex situ hot pressing method (252.0 MPa). No cracking was found in the functionally graded materials after 10 thermal cycles up to 1000 °C due to the better metal–ceramic bond, continuous in microstructure at interface of FGM and good oxidation resistance component FeCrAl alloy formed in the FGM.     

Mechanical properties of rolled A356 based composites reinforced by Cu-coated bimodal ceramic particles

Three kinds of A356 based composites reinforced with 3 wt.% Al₂O₃ (average particle size: 170 μm), 3 wt.% SiC (average particle size: 15 μm), and 3 wt.% of mixed Al₂O₃–SiC powders (a novel composite with equal weights of reinforcement) were fabricated in this study via a two-step approach. This first process step was semi-solid stir casting, which was followed by rolling as the second process step. Electroless deposition of a copper coating onto the reinforcement was used to improve the wettability of the ceramic particles by the molten A356 alloy. From microstructural characterization, it was found that coarse alumina particles were most effective as obstacles for grain growth during solidification. The rolling process broke the otherwise present fine silicon platelets, which were mostly present around the Al₂O₃ particles. The rolling process was also found to cause fracture of silicon particles, improve the distribution of fine SiC particles, and eliminate porosity remaining after the first casting process step. Examination of the mechanical properties of the obtained composites revealed that samples which contained a bimodal ceramic reinforecment of fine SiC and coarse Al₂O₃ particles had the highest strength and hardness.     

Optimizing the tensile properties of Al–Si–Cu–Mg 319-type alloys: Role of solution heat treatment

The work presented in this study was carried out on Al–Si–Cu–Mg 319-type alloys to investigate the role of solution heat treatment on the dissolution of copper-containing phases (CuAl₂ and Al₅Mg₈Cu₂Si₆) in 319-type alloys containing different Mg levels, to determine the optimum solution heat treatment with respect to the occurrence of incipient melting, in relation to the alloy properties. Two series of alloys were investigated: a series of experimental Al–7 wt% Si–3.5 wt% Cu alloys containing 0, 0.3, and 0.6 wt% Mg levels. The second series was based on industrial B319 alloy. The present results show that optimum combination of Mg and Sr in this study is 0.3 wt% Mg with 150 ppm Sr, viz. for the Y4S alloy. The corresponding tensile properties in the as-cast condition are 260 MPa (YS), 326 MPa (UTS), and 1.50% (%El), compared to 145 MPa (YS), 232 MPa (UTS), and 2.4% (%El) for the base alloy with no Mg. At 520 °C solution temperature, incipient melting of Al₅Mg₈Cu₂Si₆ phase and undissolved block-like Al₂Cu takes place. At the same time, the Si particles become rounder. Therefore, the tensile properties of Mg-containing alloys are controlled by the combined effects of dissolution of Al₂Cu, incipient melting of Al₅Mg₈Cu₂Si₆ phase and Al₂Cu phase, as well as the Si particle characteristics.     

Preparation and characterization of As-cast and hot-rolled Mg–3Al–0.5Mn–0.5Zn–1MM alloy

Mg–3Al–0.5Mn–0.5Zn–1MM alloy was prepared by metal mould casting method. The as-cast ingot was homogenized and then hot-rolled at 673 K with total thickness reduction of 65%. Microstructure and mechanical properties of the as-cast and hot-rolled samples were investigated. The results showed that the as-cast sample mainly consisted of α-Mg, β-Mg₁₇Al₁₂, Al₁₀Ce₂Mn₇, and Al₁₁RE₃ (RE = La and Ce) phases. The average grain size of the sample homogenized at 673 K was about 240 μm, and it was greatly refined to about 7 μm by dynamic recrystallization for the hot-rolled sample. The ultimate tensile strength and 0.2% yield strength of the hot-rolled sample were 300 MPa and 230 MPa, respectively. They were enhanced by 55% and 400% correspondingly compared with those of the as-cast sample. The improvement of the strengths was attributed to the refined grains, breakup of the precipitates and increase of the dislocation density.     

Effect of 10Ce-TZP/Al2O3 nanocomposite particle amount and sintering temperature on the microstructure and mechanical properties of Al/(10Ce-TZP/Al2O3) nanocomposites

A zirconia/alumina nanocomposite stabilized with cerium oxide (Ce-TZP/Al₂O₃ nanocomposite) can be a good substitute as reinforcement in metal matrix composites. In the present study, the effect of the amount of 10Ce-TZP/Al₂O₃ particles on the microstructure and properties of Al/(10Ce-TZP/Al₂O₃) nanocomposites was investigated. For this purpose, aluminum powders with average size of 30 μm were ball-milled with 10Ce-TZP/Al₂O₃ nanocomposite powders (synthesized by aqueous combustion) in varying amounts of 1, 3, 5, 7, and 10 wt.%. Cylindrical-shape samples were prepared by pressing the powders at 600 MPa for 60 min while heating at 400–450 °C. The specimens were then characterized by scanning and transmission electron microscopy (SEM and TEM) in addition to different physical and mechanical testing methods in order to establish the optimal processing conditions. The highest compression strength was obtained in the composite with 7 wt.% (10Ce-TZP/Al₂O₃) sintered at 450 °C.     

Improving the mechanical properties of Al2O3/Ni laminated composites by adding Ni particles in Al2O3 layers

The (Al₂O₃ + Ni) composite, (Al₂O₃ + Ni)/Ni and Al₂O₃/(Al₂O₃ + Ni)/Ni laminated materials were prepared by aqueous tape casting and hot pressing. Results indicated that the (Al₂O₃ + Ni) composite had higher strength and fracture toughness than those of pure Al₂O₃. The fracture toughness of (Al₂O₃ + Ni)/Ni and Al₂O₃/(Al₂O₃ + Ni)/Ni laminated materials was higher than not only those of pure Al₂O₃, but also those of Al₂O₃/Ni laminar with the same layer numbers and thickness ratio. It was found that the toughness of the Al₂O₃/(Al₂O₃ + Ni)/Ni laminated material with five layers and layer thickness ratio = 2 could reach 16.10 MPa m^1/2, which were about 4.6 times of pure Al₂O₃. The strength and toughness of the (Al₂O₃ + Ni)/Ni laminated material with three layers and layer thickness ratio = 2 could reach 417.41 MPa and 12.42 MPa m^1/2. It indicated the material had better mechanical property.     

Effect of alumina particles loading on the mechanical properties of light-cured dental resin composites

The purpose of this study is to evaluate the effect of alumina (Al₂O₃) loading on the mechanical properties of dental resin composites (DRCs). The DRCs were prepared based on Al₂O₃ particles and bisphenol A-glycidyl methacrylate (Bis-GMA) was used as the base monomer. The silane-treated Al₂O₃ particles were mixed with the resin matrix in proportions of 40, 50, and 60 wt%, respectively. Resin matrix without filler was used as the control sample. The Vickers hardness (HV) and flexural modulus (FM) of the DRCs mixed with Al₂O₃ particles were found to be superior compared to the control sample; the values increased from 14.4 to 23.5 kg/mm² and 1.5 to 5.7 GPa, respectively. However, the flexural strength (FS) values of DRCs were slightly decreased as the filler loading increased i.e. from 84.5 to 74.2 MPa. The results also revealed statistically significant increases in the HV and FM. On the other hand, FS values showed significant decrease when filler loading was increased (P < 0.05).     

Influence of the combined addition of Y and Nd on the microstructure and mechanical properties of Mg–Li alloy

Y and Nd are simultaneously added into Mg–5Li–3Al–2Zn alloy. It is found that there exist the phases of α-Mg, AlLi, Al₁₁Nd₃ and Al₂Y in the alloys. When the contents of Y and Nd are 1.2% and 0.8%, respectively, the grain is the finest with an average size of 30 μm, and the tensile strength of the alloy reaches 231 MPa, the elongation reaches 16%. When the ratio of Y to Nd is 1.2:0.8, there is a synergistic strengthening effect.     

Alumina–tantalum composite for femoral head applications in total hip arthroplasty

Dense composite laminates of alumina (Al₂O₃) and tantalum (Ta) were fabricated by hot pressing and tested in vitro for potential use as a femoral head material in total hip arthroplasty (THA). Al₂O₃–Ta composite laminates hot pressed at 1450 °C and 1650 °C had flexural strengths of 940 ± 180 MPa and 1090 ± 340 MPa, respectively, which were far larger than the values of 420 ± 140 MPa and 400 ± 130 MPa for Al₂O₃ hot pressed at 1450 °C and 1650 °C, respectively. The interfacial shear strength, determined by a double-notched specimen test, was 310 ± 80 MPa for the composite laminate hot pressed at 1650 °C, indicating strong interfacial bonding between Al₂O₃ and Ta. Scanning electron microscopy (SEM), energy dispersive X-ray (EDS) analysis, and X-ray mapping of polished sections of the hot-pressed laminates showed the presence of an interfacial region formed presumably by diffusion of O (at 1450 °C) or O and Al (1650 °C) from Al₂O₃ into Ta. Composite femoral heads of Al₂O₃ and Ta could combine the low wear of an Al₂O₃ articulating surface with the safety of a ductile metal femoral head.     

Effect of (α + β) heat treatment on microstructure and mechanical properties of (TiB + TiC)/Ti–B20 matrix composite

For the first stage, a metastable β titanium alloy, Ti–3.5Al–5Mo–4V–2Cr–2Sn–2Zr–1Fe reinforced with trace amounts of TiB whiskers and TiC particles was fabricated by vacuum arc melting process and hot forging followed by heat treatment at 780 °C/740 °C, then by aging at 500 °C, 550 °C, 570 °C and 600 °C. For the second stage, the unreinforced titanium alloy was also fabricated by the same process. The microstructural characteristics were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Traces of TiB whiskers and TiC particles (2.2 vol.%) with a volume ratio of 2:3 synthesized in situ exerted a hybrid reinforcing effect on the β titanium alloy. The reinforcements were uniformly distributed in the matrix and the elastic modulus was improved about 25 GPa. Ultimate tensile strength and yield strength achieves about 1625 MPa and 1500MPa respectively, with ductility at 7% when the aging temperature is 500 °C. The ductility of (TiB + TiC)/(Ti–3.5Al–5Mo–4 V–2Cr–2Sn–2Zr–1Fe) matrix composite could be enhanced by increasing the aging temperatures. After 780 °C followed by aging at 570 °C, excellent strength and plasticity properties were obtained (ultimate tensile strength of matrix alloy is 1350 MPa with elongation of 18% and ultimate tensile strength of composite is 1500 MPa with elongation of 13%).     

Infiltrated Cu8Al–Ti alumina composites

The effect of titanium additions on the interface and mechanical properties of infiltrated Cu8 wt%Al–Al₂O₃ composites containing 57 ± 2 vol% ceramic are investigated, exploring two different Al₂O₃ particle types and four different Ti concentrations (0, 0.2, 1, 2 wt%Ti). Addition of 0.2 wt%Ti leads to the development of a thin (5–10 nm) layer enriched in Ti at the interface between Cu alloy and Al₂O₃ particles; this Ti concentration produces the best mechanical properties. With higher Ti-contents Ti₃(Cu, Al)₃O appears; this decreases both the interface and composite strength. Composites reinforced with vapor-grown polygonal alumina particles show superior mechanical properties compared to those reinforced by angular comminuted alumina particles, as has been previously documented for aluminum-based matrices. Micromechanical analysis shows that damage accumulation is more extensive, as is matrix hardening by dislocation emission during composite cooldown, in the present Cu8 wt%Al matrix composites compared with similarly reinforced and processed Al-matrix composites.     

In situ fabrication of α-Al2O3 and Ni2Al3 reinforced aluminum matrix composites in an Al–Ni2O3 system

α-Al₂O₃ ceramic particles and Ni₂Al₃ intermetallic compound reinforced aluminum matrix composites were successfully fabricated via exothermic dispersion (XD) reaction in an Al–Ni₂O₃ system. Thermodynamic analysis indicated that the reaction between Al and Ni₂O₃ could occur spontaneously due to its negative Gibbs free energy. The reaction characteristic was discussed by using X-ray diffraction (XRD) method and differential scanning calorimetry (DSC) analysis. The results showed that the reactions of the Al–Ni₂O₃ system consisted of two steps as following: (1) the Al firstly reacted with Ni₂O₃ to form the stable α-Al₂O₃ particles and active Ni atoms; (2) the active Ni atoms further reacted with Al to form Ni₂Al₃. The values of activation energy of the two step reactions were around 457.3 and 282.4 kJ/mol, respectively. The scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS) revealed that the Ni₂Al₃ blocks were uniformly distributed throughout the matrix, while the α-Al₂O₃ particles were slightly segregated in the matrix. The strength of the composite is controlled by the strength of Ni₂Al₃ phase, and the tensile strength and the elongation rate of the composite with 30 vol.% reinforcement volume fraction are 210 MPa and 8%, respectively.