Development of gas electron multiplier foils with a laser etching technique

Fine-pitch gas electron multiplier (GEM) foils have been produced for cosmic X-ray polarimeters using a carbon dioxide laser etching technique. The finest hole pitch of the foil which can be produced repeatedly is and the smallest hole diameter is . The electron amplification factor was measured as a function of applied voltage. The behavior of the factor is almost the same as the -pitch standard foil fabricated by CERN. Our GEMs had no rate-dependent gain instability, which is expected of the GEMs having holes of good cylindrical geometry. The amplification factor of the foil in a mixture of 70% argon and 30% carbon dioxide reaches about 5000 without any micro-discharge at a voltage of 570 V between foil electrodes.     

The time-of-flight technique for the HERMES experiment

This paper describes the use of the time-of-flight (TOF) technique as a particle identification method for the HERMES experiment. The TOF is measured by two scintillation hodoscopes that initially were designed only for the first-level trigger. However, the suitable time structure of the HERA electron beam allows an extension of their functions to also measure the TOF for low momentum hadron identification. Using only these conventional hodoscopes, good particle identification was achieved for protons and pions in the momentum range up to and for kaons up to .     

Background reduction in neutrinoless double beta decay experiments using segmented detectors—A Monte Carlo study for the GERDA setup

The identification of gamma radiation is essential for a new generation of double beta decay experiments. The GERmanium Detector Array, GERDA, located at the INFN Gran Sasso National Laboratory (LNGS) in Italy, uses germanium, enriched in , as source and detector, and aims at a background level of less than in the region of the Q_ββ-value. For the first time highly segmented detectors will be installed in a double beta decay experiment. A detailed GEANT4 Monte Carlo study was performed to evaluate the background reduction achievable by anti-coincidence cuts between crystals and segments.

Within the overall geometry of GERDA, the segmentation scheme considered here provides around an order of magnitude of extra background reduction.     

Position sensitivity of the TIGRESS 32-fold segmented HPGe clover detector

Sensitivity to the locations of γ-ray interactions within a 32-fold segmented clover-type HPGe detector has been investigated through 90 Compton scattering of -rays from a collimated source. A mean position sensitivity of 0.44 mm at an energy of 373 keV is deduced by comparing the average pulse shapes for net charge collecting signals, as well as transient induced signals in neighbouring contacts, from 1007 pairs of three-dimensionally localized interaction points. The reconstruction of individual event locations based on a χ² comparison with the measured set of basis waveforms is presented.     

A 5 ps TOF-counter with an MCP–PMT

We measured the timing resolution of TOF counters by means of Cherenkov-light detection with a Micro-Channel Plate Photo-Multiplier Tube, and attained using pion-beams with a readout electronics of 4.1 ps resolution. The optimum radiator thickness was examined and the detectable number of photo-electrons was analyzed.     

Production of a low-energy radioactive nuclear beam with high purity using JAERI-RMS

Low-energy (1–2 MeV/nucleon) radioactive nuclear beams (RNBs) of ⁸Li, ¹²B and ¹⁶N have been produced through nuclear transfer reactions using a recoil mass separator (RMS) at Japan Atomic Energy Research Institute (JAERI). The contamination of the primary beam to the RNB was investigated quantitatively and was well suppressed. The typical beam intensities of ⁸Li-, ¹²B- and ¹⁶N-RNB were 1.4×10⁴, 7.8×10³ and , respectively. Their purities were 99%, 98% and 98.5%, respectively.     

Liquid-filled ionization chamber temperature dependence

Temperature and pressure corrections of the read-out signal of ionization chambers have a crucial importance in order to perform high-precision absolute dose measurements. In the present work the temperature and pressure dependences of a sealed liquid isooctane filled ionization chamber (previously developed by the authors) for radiotherapy applications have been studied.

We have analyzed the thermal response of the liquid ionization chamber in a interval around room temperature. The temperature dependence of the signal can be considered linear, with a slope that depends on the chamber collection electric field. For example, a relative signal slope of for an operation electric field of has been measured in our detector. On the other hand, ambient pressure dependence has been found negligible, as expected for liquid-filled chambers.

The thermal dependence of the liquid ionization chamber signal can be parametrized within the Onsager theory on initial recombination. Considering that changes with temperature of the detector response are due to variations in the free ion yield, a parametrization of this dependence has been obtained. There is a good agreement between the experimental data and the theoretical model from the Onsager framework.     

Differential die-away analysis system response modeling and detector design

Differential die-away-analysis (DDAA) is a sensitive technique to detect presence of fissile materials such as and . DDAA uses a high-energy (14 MeV) pulsed neutron generator to interrogate a shipping container. The signature is a fast neutron signal hundreds of microseconds after the cessation of the neutron pulse. This fast neutron signal has decay time identical to the thermal neutron diffusion decay time of the inspected cargo. The theoretical aspects of a cargo inspection system based on the differential die-away technique are explored. A detailed mathematical model of the system is developed, and experimental results validating this model are presented.     

A NaI activation method for the measurement of the weak thermal neutron field around the MEG experiment

A precise measurement of the thermal neutron flux (and an approximate measurement of the non-thermal neutron flux), associated with the high intensity stopping μ⁺ beam (≈) of the MEG experiment, was studied by measuring the delayed radioactivity of an activated NaI detector. This passive method provides a high sensitivity and allows the neutron flux determination at all locations, even in regions of high magnetic field. We present and discuss the results.     

Study on the Raman scattering measurements of Mn ion implanted GaN

We investigate the temperature dependent Raman spectra of Mn implanted (Ga,Mn)N samples with five Mn implantation doses. A small shoulder at 572.4 cm⁻¹ on the high energy side of the main Raman peak has been attributed to the Mn-related local vibrational mode (LVM). It is found that with the increase of Mn implantation dose the intensity ratio of LVM to that of the increases at first and tends to saturate at high implantation dose. In addition, at high temperature or after rapid thermal anneal treatment, the value of decreases significantly, explaining the reason why it is difficult to observe Mn-related LVM reported in the literature.     

A parametric study of a pressurized blister test for an elastic–plastic film-rigid substrate system

A finite element simulation of a blister test of an elastic–plastic film, bonded to a substrate and subject to plane strain conditions, is performed. A traction-separation law models the fracture process ahead of the crack tip at the interface between the thin film and the substrate. Only two parameters are significant in describing the traction-separation law: adhesion energy, Γ₀ and interface strength, . The dependences of the pressure, P, and the product of the pressure with the central deflection, PH, on the adhesion properties (Γ₀ and ), the geometry and material properties of the film are studied. The latter quantity (PH) has the same unit as the adhesion energy, Γ₀, and is “conceptually” appropriate for the analysis. We suggest a method to extract the adhesion energy, Γ₀ and the interface strength, , independently from the total energy dissipated.     

Development of a high-efficiency pulsed slow positron beam for measurements with orthopositronium in vacuum

We have developed a high-efficiency pulsed slow positron beam for experiments with orthopositronium in vacuum. The new pulsing scheme is based on a double-gap coaxial buncher powered by an RF pulse of appropriate shape. The modulation of the positron velocity in the two gaps is used to adjust their time-of-flight to a target. This pulsing scheme allows to minimize non-linear aberrations in the bunching process and to efficiently compress positron pulses with an initial pulse duration ranging from 300 to 50 ns into bunches of 2.3 to 0.4 ns width, respectively, with a repetition period of . The compression ratio achieved is 100, which is a factor 5 better than has been previously obtained with slow positron beams based on a single buncher. Requirements on the degree, to which the moderated positrons should be mono-energetic and on the precision of the waveform generation are presented. Possible applications of the new pulsed positron beam for measurements of thin films are discussed.     

The I-meter, a distributor unit for the OPERA RPC HV system

The OPERA RPC HV system has been implemented using custom current measurement/distribution systems developed by the LNF Electronics Workshop.

Each system features eight inputs and 24 outputs (1–3 modularity). The current on each channel is measured with 100 pA sensitivity and 3% accuracy in the 1 nA– range.

In the paper we describe the measurement circuit as well as the results of the tests we have carried out to qualify the system.     

A new analogue sampling readout system for the COMPASS RICH-1 detector

A new electronic readout for CsI-coated multiwire proportional chambers (MWPC), used as photon detectors in the COMPASS ring imaging Cherenkov (RICH) detector, is described. A prototype system comprising more than 5000 channels has been built and tested in high-intensity beam conditions. It is based on the APV25-S1 analogue sampling chip, and replaces the GASSIPLEX chip readout used previously. The APV25 chip, although originally designed for Silicon microstrip detectors, is shown to perform well even with “slow” signals from an MWPC, maintaining a signal-to-noise ratio (SNR) of 9. For every trigger the system reads out three consecutive amplitudes in time, thus allowing to extract information on both the signal amplitude and its timing. This information is used to reduce pile-up events in a high-rate environment. Prototype tests of the new readout electronics on a central RICH photocathode in nominal COMPASS beam conditions showed that the effective time window is reduced from more than for the GASSIPLEX to less than for the APV25 chip. This leads to a significant improvement of the signal-to-background ratio (SBR) with respect to the original readout. A gain by a factor of 5–6 was experimentally verified in the very forward region of phase space, where pile-up due to the muon beam halo is most significant. Owing to its pipelined architecture, the new readout system also considerably reduces the dead time per event, thus allowing to make use of trigger rates exceeding .     

Detection of single electrons by means of a Micromegas-covered MediPix2 pixel CMOS readout circuit

A small drift chamber was read out by means of a MediPix2 readout chip as a direct anode. A Micromegas foil was placed above the chip, and electron multiplication occurred in the gap. With a He/isobutane 80/20 mixture, gas multiplication factors up to tens of thousands were achieved, resulting in an efficiency for detecting single electrons of better than 90%. We recorded many frames containing 2D images with tracks from cosmic muons. Along these tracks, electron clusters were observed, as well as δ-rays.     

Performance optimisation of the micro pixel chamber

A thorough performance analysis of large-area μ-PIC detectors has been made. Through systematic simulations and comparison with test results of the two detector versions, μ-PIC1 and μ-PIC3, we have identified that low primary electron collection was responsible for the degradation of measured gas gain of the μ-PIC3 device. The test of a new detector, μ-PIC5, fabricated with a narrower inter-cathode gap and anodes raised above the insulator surface, shows a threefold increase in gas gain reaching 10⁴ in argon 80%–ethane 20% gas mixture, which agrees with simulations. The new detector demonstrates a stable long-term operation at high gains, above 6000 measured during more than 70 h with an X-ray source, with a moderate 6% gain increase due to dielectric polarisation.     

A 600 kV 15 mA Cockcroft–Walton high-voltage power supply with high stability and low-ripple voltage

A Cockcroft–Walton high-voltage power supply with high stability and low-ripple voltage has been developed. This power supply has been operated in a ns pulse neutron generator. The maximum non-load voltage is 600 kV while the working voltage and load current are 550 kV and 15 mA, respectively. The tested results indicate that when the power supply is operated at 300 kV, 6.7 mA and the input voltage varies ±10%, the long-term stability of the output voltage is S=(0.300–1.006)×10^-3. The ripple voltage is at 300 kV, 6.8–8.3 mA and the ratio of δU_P−P to the output voltage V_H is δU_P-P/V_H=2.1×10^-5.     

Magnetic field effects on particle trajectories in the muon-spin relaxation experiment: Towards a high-field spectrometer

As a step towards the design of a muon-spin relaxation (μ⁺SR) spectrometer with a high magnetic field capability, we have carried out an investigation into the effects of applying a large magnetic field on the trajectories of particles in a μ⁺SR experiment. We compare the results of measurements and Geant4 simulations of the influence of applied fields on the incoming muon beam and the outgoing decay positron ensemble. Good agreement between measurements and simulations is found and the limits of this agreement are discussed.     

A novel apparatus for the investigation of material properties for the storage of ultracold neutrons

We have built a novel apparatus for the investigation of materials for the storage of ultracold neutrons. Neutrons are filled into a storage volume, confined at the bottom by a magnetic field, at the top by gravity and at the sides by the slit-less sample surface under investigation. For different beryllium and diamond-like carbon samples, storage times up to 200 s were obtained at room temperature. The corresponding loss parameters η for ultracold neutrons varied between 4.2 and 6.8×10^-4 per wall collision.     

Dissociated dislocations in Ni: a computational study

A systematic computational study of the behavior of a dissociated screw dislocation in fcc nickel is presented, in which atomic interactions are described through an embedded-atom potential. A suitable external stress is applied on the system, both for modifying the equilibrium separation distance d and moving the dislocation complex. The structure of the dislocation and its corresponding changes during the motion are studied in the framework of the two-dimensional Peierls model, for different values of the ratio d/a^′, where a^′ is the period of the Peierls potential. The distance between the edge and screw components of the partials, as well as their widths, undergo a modulation with period a^′, as the dislocation moves, and the amplitudes of such oscillations are shown to depend on d/a^′. The stress profile acting on the dislocation complex is analyzed and the effective Peierls stress is estimated for different values of d/a^′.