Synthesis,characterization and formaldehyde gas sensitivity of La0.7Sr0.3FeO3 nanoparticles assembled nanowires

La_0.7Sr_0.3FeO₃ nanoparticles assembled nanowires were synthesized by a hydrothermal method assisted with cetyltrimethylammonium bromide (CTAB). The hydrothermal temperature was 180 °C and the annealed temperature was 700 °C. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the morphology, composition and structural properties of the materials. The results showed that the La_0.7Sr_0.3FeO₃ nanoparticles assembled nanowires had a high aspect ratio (the largest aspect ratio >100); the size of the nanoparticles was about 20 nm and the diameter of the nanowires was about 100–150 nm. The growth mechanism of La_0.7Sr_0.3FeO₃ nanowires was discussed. Gas sensors were fabricated by using La_0.7Sr_0.3FeO₃ nanowires. Formaldehyde gas sensing properties were carried out in the concentration range of 0.1–100 ppm at the optimum operating temperature of 280 °C. The response and recovery times to 20 ppm formaldehyde of the sensor were 110 s and 50 s, respectively. The gas sensing mechanism of La_0.7Sr_0.3FeO₃ nanowires was investigated.     

Calcium-doping for enhanced temperature stability of (Ba0.6Sr0.4)1−xCaxTiO3 thin film dielectric properties

Ternary (Ba_0.6Sr_0.4)_1−xCa_xTiO₃ (BSCT) (x = 0, 0.1, 0.2, 0.3 and 0.4) thin films with thickness of around 500 nm were prepared on Pt(111)/TiO₂/SiO₂/Si substrates by sol-gel methods. BSCT forms the complete solid solutions in a single cubic perovskite structure. The lattice constant, dielectric constant, tanδ and tunability of BSCT decrease, whereas the temperature stability of dielectric properties increases with increasing the Ca concentration. From 25 to 100 °C, the decrease of tunability is about 11% for BSCT with 40 at.% of Ca. BSCT thin films exhibit the comparable tunability, low loss and enhanced temperature stability.     

Microstructure control of (Pb,Sr)TiO3 films on Pt/Ti/SiO2/Si substrates by a TiO2 buffer layer

A thin TiO₂ buffer layer was used to control the microstructure and electrical properties of the polycrystalline (Pb,Sr)TiO₃ (PST) films produced by a Sol-Gel method on Pt(111)/Ti/SiO₂/Si(100) substrates. The PST films included (Pb_0.6Sr_0.4)TiO₃ (PST40) and (Pb_0.4Sr_0.6)TiO₃ (PST60). It was found that a crystallized TiO₂ buffer layer with a thickness of nearly 5 nm was critical for improving the crystallinity and surface morphology of both the thinner (about 40 nm) and thicker (about 330 nm) PST films, which exhibited a (l00) preferred orientation and much smoother surface comparing with those without the buffer layer. The electrical properties of the PST films having TiO₂ buffer layer were also improved. For 330-nm-thick PST40 films, the dielectric constant and its tunability by dc voltage were increased from 482 and 26.8% at 10 kHz to 590 and 51.2%, while the loss and leakage current density were reduced from 0.04 and 4.26 × 10⁻⁴ A/cm² at 100 kV/cm to 0.034 and 7.63 × 10⁻⁶ A/cm², respectively. Similar results were also found in the PST60 films.     

Synthesis of nanosized perovskite (Ba,Sr)TiO3 powder via a PVA modified sol-precipitation process

Ba_0.55Sr_0.45TiO₃ (BST) precursors were synthesized via a polyvinyl alcohol (PVA) modified sol-precipitation route. And the obtained precursors were then calcined in air at temperatures ranging from 400 to 800 °C. The formation mechanism of BST phase was investigated using X-ray diffraction (XRD), while the effect of PVA on the particle morphology of the BST phase was studied by using scanning electron microscopy (SEM). The results show that the introduction of PVA significantly affects the morphology of the BST powders. High purity nanocrystalline powders were synthesized by calcination of the BST precursors encapsulated by PVA gel, with narrow particle distribution (30-80 nm) and being nearly free of agglomeration. While, large particles (40-170 nm) with evident agglomeration were obtained from the solution without PVA.     

Influence of Ca0.8Sr0.2TiO3 on the microstructures and microwave dielectric properties of Nd(Mg0.4Zn0.1Sn0.5)O3 ceramics

The influence of Ca_0.8Sr_0.2TiO₃ on the microstructures and microwave dielectric properties of Nd(Mg_0.4Zn_0.1Sn_0.5)O₃ ceramics were investigated by the conventional solid-state method. The X-ray diffraction peaks of (1 − x)Nd(Mg_0.4Zn_0.1Sn_0.5)O₃–xCa_0.8Sr_0.2TiO₃ ceramic system shifted to higher angles as x increased. The dielectric constant increased from 31.8 to 47.7, the quality factor (Q × f) decreased from 54,200 to 42,800 GHz, and the temperature coefficient of resonant frequency (τ _f ) increased from −43 to +41 ppm/°C as x increased from 0.5 to 0.7 when (1 − x)Nd(Mg_0.4Zn_0.1Sn_0.5)O₃–xCa_0.8Sr_0.2TiO₃ ceramic system sintered at 1,600 °C for 4 h.     

Synthesis of barium strontium titanate nanorods in reverse microemulsion

Perovskite Ba_0.7Sr_0.3TiO₃ nanorods were synthesized in Triton X-100 reverse microemulsion at room temperature and characterized by XRD, ICP-AES, ED and TEM. The Ba_0.7Sr_0.3TiO₃ nanorods with a diameter of 60-100 nm and a length of 450-1200 nm showed a single-crystalline tetragonal structure. The size of nanorods was effectively tuned by changing w value (molar ratio of water to surfactant), aging time and reactant concentration.     

Crystallinity enhancement of flame-made LiCo0.25Ni0.75O2 nanoparticles by heat-treatment

LiCo_0.25Ni_0.75O₂ nanoparticles of 22.8 nm in geometric mean diameter were synthesized by flame spray pyrolysis from aqueous droplets of nitrate compounds of lithium, cobalt and nickel. The crystallinity of the as-prepared LiCo_0.25Ni_0.75O₂ particles was enhanced by post-heat-treatment at various conditions, such as temperature, duration, and atmospheric gas with different flow rates. The effect of heat-treatment on the particle morphology and crystallinity was investigated systematically. Higher heat-treating temperature under normal air atmosphere improved hexagonal ordering and sufficient O₂ flow during the heat-treatment reduced the cation mixing problem.     

Synthesis of highly-active single-crystalline TiO2 nanorods and its application in environmental photocatalysis

Highly-active anatase TiO₂ nanorods have been successfully synthesized via a simple two-step method, hydrothermal treatment of anatase/rutile titanium dioxide nanoparticle powder in a composite-hydroxide eutectic system of 1:1 M KOH/NaOH, followed by acid post-treatment. The morphology and crystalline structure of the obtained nanorods were characterized using XRD, TEM, SEM/EDX and BET surface area analyzer. The obtained TiO₂ nanorods have a good crystallinity and a size distribution (about 4-16 nm); with the dimensions of 200-300 nm length and of 30-50 nm diameter. Compared with its precursor anatase/rutile TiO₂ nanoparticles and the titanate nanotubes, the pure anatase TiO₂ nanorods have a large specific surface area with a mesoporous structure. The photocatalytic performance of the prepared nanorods was tested in the degradation of the commercial Cibacrown Red (FN-R) textile dye, under UV irradiation. Single-crystalline anatase TiO₂ nanorods are more efficient for the dye removal.     

Microwave assisted low temperature rapid synthesis of manganite system using La0.67Ce0.03Sr0.3MnO3 mini-cavity furnace

Amorphous La_0.7Sr_0.3MnO₃ (LSMO) and La_0.7Ca_0.3MnO₃ (LCMO) precursor powders synthesized by the citrate gel method at 673 K, have been found to crystallize by microwave irradiation in just 60 s using La_0.67Ce_0.03Sr_0.3MnO₃ (Ce-LSMO) as couplant. This is the lowest temperature treatment and synthesis time so far reported in literature for the formation of manganite systems. Using ceramic route, the same amorphous samples crystallize on heat treatment only at temperatures greater than 1000 K. The microwave heating through this method is novel and has tremendous potential for accelerating the evolution of the product phase in very shorter durations, with just low temperature processing of the precursors, which cannot be realized in normal process.     

Synthesis of nano-particles of anatase-TiO2 and preparation of its optically transparent film in PVA

Anatase-TiO₂ nano-particles have been synthesized by using long-carbon chain carboxylic acid and titanium tetrachloride (TiCl₄). As-prepared powder has been calcined at 500 °C to obtain highly crystalline TiO₂. Broad X-ray diffraction (XRD) pattern of as-prepared as well as calcined powder showed all prominent peaks for tetragonal crystal structure representing anatase-TiO₂. The particle diameter by applying Scherrer formula was found to be about 20 nm. It was possible to load as-prepared particles in poly vinyl alcohol (PVA) for optical studies. Optically transparent film showed sharp absorption band for TiO₂ nano-particles at ∼ 300 nm. Photoluminescence (PL) studies of the solution showed emission wavelength at about 330 nm. Transmission electron microscopy (TEM) and selected area electron diffraction (SAED) revealed that the particles in the film have uniform distribution and even for the powder no agglomeration was observed. Thermal analysis (TGA) showed that the stability of host polymer is enhanced. FTIR spectra showed presence of carboxylate functional group in the powder.     

Preparation and photocatalytic study of fibrous K0.3Ti4O7.3(OH)1.7–anatase TiO2 nanocomposite photocatalyst

Nanocomposite of K_0.3Ti₄O_7.3(OH)_1.7 fiber and anatase TiO₂ nanoparticle was prepared by hydrothermal treatment of the K_0.3Ti₄O_7.3(OH)_1.7 which was synthesized by calcination of K₂CO₃ and TiO₂ at 1250 °C followed by refluxing in nitric acid. Effects of hydrothermal treatment conditions such as temperature and time on morphology, phase composition and crystal structure of the nanocomposites were extensively studied. Photocatalytic activities of the catalysts prepared at various hydrothermal conditions were evaluated by means of methylene blue decomposition under blacklight irradiation.     

Characterization and photoactivity of TiO2 sols prepared with triethylamine

Using triethylamine as a surface protective agent, a transparent and pale yellowish TiO₂ sol had been prepared at 90 °C. This method was very different from the traditional methods, which produced titanium dioxide nanoparticles with anatase crystalline structure either at high acid condition or high temperature. X-ray diffraction (XRD) and transmission electron spectroscopy (TEM) demonstrated that the as-prepared TiO₂ sol nanoparticles with anatase crystalline structure were uniformly distributed, and the average size was 3 nm. X-ray photoelectron spectroscopy (XPS) and UV-vis absorption spectra showed that triethylamine was adsorbed on TiO₂ sol particles surface. FTIR spectroscopy noted that TiO₂ sol particles had the similar spectra with Degussa P25. Photoactivity of the as-prepared TiO₂ sol was studied by investigating the photodegradation of methyl violet in hydrosol reaction system under visible light irradiation.     

The properties of Ba0.5Sr0.5TiO3 thin film prepared by RF magnetron sputtering from powder target

The Ba_0.5Sr_0.5TiO₃ (BST) thin film with the thickness of 400 nm deposited from powder target is prepared by the radio-frequency magnetron sputtering technique. The deposition rate of BST film is estimated to be 45 nm/min, which is very fast for ferroelectric materials. The dielectric properties of the as-prepared BST thin film are demonstrated. High dielectric tunability up to 42.7% and low dielectric loss small to 0.01 are achieved at a low applied voltage of 5 V. The results demonstrate that the RF magnetron sputtering from powder target is a versatile, novel technique for the deposition of high-quality ferroelectric thin films.     

Epitaxial growth and properties of cubic Zn0.7Mg0.3O films on TiN-buffered Si(100) substrates by in situ pulsed laser deposition

A novel cubic Zn_0.7Mg_0.3O film on silicon substrate is conducted by KrF excimer pulsed-laser ablation system. By introducing a thin TiN buffer, layer-by-layer growth of cubic Zn_0.7Mg_0.3O film epilayer has been realized. The overall growth process was monitored in situ by reflection high-energy electron diffraction (RHEED) method. It was found that the crystallinity and surface morphology of the Zn_0.7Mg_0.3O films were strongly affected by the TiN buffer layer. The Zn_0.7Mg_0.3O film obtained at an optimal buffer layer exhibited high quality and good surface. For the metal-insulator-metal (MIM) structure of Pt/Zn_0.7Mg_0.3O (200 nm)/TiN (20 nm)/Si (400 μm) prepared at the optimal growth conditions achieved a very low leak current density of ∼10⁻⁶ A cm⁻² at an electric field of 9 × 10⁵ V cm⁻¹ and the permittivity (?_r) of about 8.1, agreed well with that of acquired MgO film and MgO single crystal.     

Effect of high temperature post-annealing of La0.7Sr0.3MnO3 films deposited by radio frequency magnetron sputtering on SiO2/Si substrates heated at low temperature

La_0.7Sr_0.3MnO₃ thin films were deposited on SiO₂/Si substrates by RF magnetron sputtering under different oxygen gas flow rates with a sputtering power of 100 W. During deposition, the substrate was heated at 623 K. To investigate post-annealing effects, the as-deposited La_0.7Sr_0.3MnO₃ thin films were thermal-treated at 973 K for 1 h. The effects of oxygen gas flow rate and post-annealing treatment on the physical properties of the films were systematically studied. X-ray diffraction results show that the growth orientation and crystallinity of the films were greatly affected by the oxygen gas flow rate and substrate heating during deposition. The sheet resistance of the films gradually decreased with increasing oxygen gas flow rate, while the post-annealed films showed the opposite behavior. The temperature coefficient of resistance at 300 K of La_0.7Sr_0.3MnO₃ thin films deposited at an oxygen gas flow rate of 40 sccm decreased from − 2.40%/K to − 1.73%/K after post annealing. The crystalline state of the La_0.7Sr_0.3MnO₃ thin films also affected its electrical properties.     

Synthesis and performance of LiMn0.7Fe0.3PO4 cathode material for lithium ion batteries

Pure and carbon-containing olivine LiMn_0.7Fe_0.3O₄ were synthesized at 600 °C by the method of solid-state reaction. Structure, surface morphology and charge/discharge performance of LiMn_0.7Fe_0.3O₄ were characterized by X-ray diffraction, scanning electron microscopy, and electrochemical measurement, respectively. The prepared materials with and without carbon both show the single olivine structure. The morphologies of primary particles are greatly affected by the addition of carbon. Large particles (500-1000 nm) and densely sintered blocks were observed in pure LiMn_0.7Fe_0.3PO₄, which made the insertion and extraction of lithium ions difficult. Battery made from this sample can not charge and discharge effectively. The carbon-containing LiMn_0.7Fe_0.3PO₄ has a small particle size (100-200 nm) and a regular appearance. This material demonstrates high reversible capacity of about 120 mAh g⁻¹, perfect cycling performance, and excellent rate capability. It is obvious that the addition of carbon plays an important role in restricting the particle size of the material, which helps to prepare LiMn_0.7Fe_0.3PO₄ with excellent electrochemical performance. The electrochemical reaction resistance is much lower in the partly discharged state than in the fully charged or fully discharged state by the measurement of ac impedance for carbon-containing LiMn_0.7Fe_0.3PO₄. It is indicated that the mixed-valence of Fe³⁺/Fe²⁺ or Mn³⁺/Mn²⁺ is beneficial to the transfer of electron which happens between the interface.     

Dielectric and tunable properties of Pb0.25BaxSr0.75−xTiO3 thin films fabricated by a modified sol-gel method

A modified sol-gel method was used to fabricate (Pb_0.25Ba_x Sr_0.75−x)TiO₃ (PBST) thin films with x = 0.05,0.1,0.15 and 0.2 on Pt/TiO₂/SiO₂/Si substrate. The structure, surface morphology, dielectric and tunable properties of PBST thin films were investigated as a function of barium content (x). X-ray diffraction and scanning electron microscopy analysis showed that we could get pure PBST perovskite phase and relative fine density thin films with smooth surface. It was found that the crystal lattice constant, grain size, room temperature dielectric constant, dielectric loss and tunability of Ba solutionizing PST thin films increased with the increase in Ba content. For (Pb_0.25Ba_0.2Sr_0.55)TiO₃ thin film, it had the highest dielectric constant of 1390 and the largest tunability of 80.6%. The figure of merit parameter reached a maximal value of 28.9 corresponding to the (Pb_0.25Ba_0.05 Sr_0.7)TiO₃ thin film, whose dielectric constant, dielectric loss and tunability measured at 1 MHz were 627, 0.024 and 69.4%, respectively.     

Synthesis and optical properties of TiO2 nanoparticles

Ultrafine TiO₂ particles have been synthesized successfully by a facile gas flame combustion method. The synthesized sample is characterized by X-ray diffraction (XRD), transmission electron micrograph (TEM), Fourier transform infrared (FTIR), and photoluminescence (PL) spectroscopy. The as-prepared TiO₂ nanoparticles appear to be a single anatase crystalline phase and the diameter is about 9 nm. Besides a sharp emission at 398 nm originating from the radiative annihilation of excitions, a weak broad band at about 434 nm from the defect-related emission is also discussed.     

Microstructures of YBa2Cu3O7/La0.7Ca0.3MnO3 and La0.7Ca0.3MnO3/YBa2Cu3O7 bi-layers grown on (001)LaAlO3

Epitaxial YBa₂Cu₃O₇/La_0.7Ca_0.3MnO₃ (YBCO/LCMO) bi-layers and La_0.7Ca_0.3MnO₃/YBa₂Cu₃O₇ (LCMO/YBCO) bi-layers were grown on (001)LaAlO₃ by pulsed laser deposition, and their microstructures were compared by transmission electron microscopy investigation. In the YBCO(100 nm)/LCMO(150 nm) bi-layers, the LCMO layer consists of columnar grains of ~ 17 nm in diameter and contains mixed orientation domains of [100]_c, [010]_c and [001]_c. The YBCO layer is totally c-axis oriented and the YBCO lattices are tilted − 2.5° to + 2.5° as they grew on the rough surfaces of LCMO columnar grains. For the LCMO(140 nm)/YBCO(140 nm) bi-layers, the LCMO/YBCO interface is sharp and flat. The initial 12-nm thickness of the YBCO layer is composed of c-axis oriented domains, and the upper part of YBCO layer is [100] oriented. The LCMO layer was predominantly [001]_c oriented while [100]_c-oriented domains were occasionally observed.     

Influence of oxygen partial pressure on the structural and dielectric properties of Ba(Zr0.3Ti0.7)O3 thin films grown on (LaAlO3)0.3(Sr2AlTaO6)0.35 (001) using pulsed laser deposition

Epitaxial Ba(Zr_0.3Ti_0.7)O₃ thin films were grown on (LaAlO₃)_0.3(Sr₂AlTaO₆)_0.35 (001) single-crystal substrates by pulsed laser deposition at 700 °C in different oxygen partial pressures ranging from 6.7 Pa to 40.0 Pa. A strong correlation is observed between the structure and dielectric properties for the Ba(Zr_0.3Ti_0.7)O₃ thin films. The tetragonal distortion (ratio of in-plane and out-of-plane lattice parameter, a/c) of the films depends on the oxygen partial pressures. a/c varies from 0.989 at 6.7 Pa to 1.010 at 40.0 Pa, indicating the in-plain strain changes from compressive to tensile. The in-plain strain (either compressive or tensile) shifts the Curie temperature of the Ba(Zr_0.3Ti_0.7)O₃ thin films dramatically. Surface morphology and dielectric properties of Ba(Zr_0.3Ti_0.7)O₃ thin films have a strong dependence of the oxygen partial pressure. The film grown 26.7 Pa, which corresponds to a moderate in-plain tensile strain and a Curie temperature of ~ 30 °C, shows the largest relative permittivity, tunability and the best figure of merit in a broad frequency range (1 kHz-500 MHz), which may be a promising candidate for room-temperature microwave device applications.