Influence of calcination temperature on luminescent properties of Sr3Al2O6:Eu, Dy phosphors prepared by sol–gel-combustion processing

The detailed preparation process of Eu²⁺ and Dy³⁺ ion co-doped Sr₃Al₂O₆ phosphor powders with red long afterglow by sol–gel-combustion method in the reducing atmosphere is reported. X-ray diffraction, scanning electron microscopy and photoluminescence spectroscopy are used to investigate the effects of synthesis temperature on the crystal characteristics, morphology and luminescent properties of the as-synthesized Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphors. The results reveal that Sr₃Al₂O₆ crystallizes completely when the combustion ash is sintered at 1200 °C. The excitation and the emission spectra indicate that the excitation broad-band lies chiefly in visible range and the phosphor powders emit strong light at 618 nm under the excitation of 472 nm. The light intensity and the light-lasting time of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphors are increased when increasing the calcination temperatures from 1050 to 1200 °C. The afterglow of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphors sintered at 1200 °C lasts for over 600 s when the excited source is cut off. The red emission mechanism is discussed according to the effect of nephelauxetic and crystal field on the 4f⁶5d¹ → 4f⁷ transition of the Eu²⁺ ions.     

Synthesis and luminescent properties of SrAl2O4:Eu green-emitting phosphor for white LEDs

SrAl₂O₄:Eu²⁺ phosphor was prepared by a solid-state reaction in CO-reductive atmosphere. X-ray powder diffraction (XRD) analysis confirmed the formation of SrAl₂O₄:Eu²⁺. Field-emission scanning electron-microscopy (FE-SEM) observation indicated that the microstructure of the phosphor consisted of irregular fine grains with an average size of about 7–8 μm. Photoluminescence measurements showed that the phosphor can be efficiently excited by UV–visible light from 350 to 430 nm, and exhibited bright green emission peaked at about 516 nm. Bright green LEDs were fabricated by incorporating the phosphor with an InGaN-based UV chip. All the characteristics indicated that SrAl₂O₄:Eu²⁺ is a good candidate phosphor applied in white LEDs.     

Influence of excitation wavelengths on luminescent properties of Sr3Al2O6:Eu, Dy phosphors prepared by sol-gel-combustion processing

Eu²⁺ and Dy³⁺ ion co-doped Sr₃Al₂O₆ red-emitting long afterglow phosphor was synthesized by sol-gel-combustion methods using Sr(NO₃)₂, Al(NO₃)₃·9H₂O, Eu₂O₃, Dy₂O₃, H₃BO₃ and C₆H₈O₇·H₂O as raw materials. The crystalline structure of the phosphors were characterized by X-ray diffraction, luminescent properties of phosphors were analyzed by fluorescence spectrophotometer. The effect of excitation wavelengths on the luminescent properties of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphors was discussed. The emission peak of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphor lays at 516 nm under the excitation of 360 nm, and at 612 nm under the excitation of 468 nm. The results reveal that the Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphor will emit a yellow-green light upon UV illumination, and a bright red light upon visible light illumination. The emission mechanism was discussed according to the effect of nephelauxetic and crystal field on the 4f⁶5d¹ → 4f⁷ transition of the Eu²⁺ ions in Sr₃Al₂O₆. The afterglow time of (Sr_0.94Eu_0.03Dy_0.03)₃ Al₂O₆ phosphors lasts for over 600s after the excited source was cut off.     

Yellow-emitting phosphor of Sr3B2O6:Eu for application to white light-emitting diodes

This work focuses on the development of Eu²⁺-doped strontium (Sr)-borate as a yellow-emitting phosphor and its application to the fabrication of white light-emitting diodes (LEDs). Synthesis of Eu²⁺-doped Sr-borate phosphors was finely tuned for obtaining the efficient yellow luminescence through varying host composition, Eu concentration, and firing temperature. The 1300 °C-fired Eu²⁺-doped Sr₃B₂O₆, which was found to be the most efficient candidate to date, was used for white LED fabrication. Their optical properties were evaluated, resulting in warm white lights with CIE chromaticity coordinates of (0.340–0.372, 0.287–0.314) and color rendering indices of 75–77 under the forward currents of 5–40 mA.     

Luminescence and energy transfer of Mn co-doped SrSi2O2N2:Eu green-emitting phosphors

Eu²⁺ and Mn²⁺ co-doped SrSi₂O₂N₂ green-phosphors, with promising luminescent properties (examined by their powder diffuse reflection, photoluminescence excitation and emission spectra) suitable for UV converted white LEDs, were produced by high temperature solid-state reaction method. The produced materials exhibited intense broad absorption bands at 220–500 nm and a broad emission band centered at ca. 530 nm, attributed to 4f–5d transitions of Eu²⁺. The emission intensity of Eu²⁺ ions was greatly enhanced by introducing Mn²⁺ ions into SrSi₂O₂N₂:Eu²⁺ due to the energy transfer from Mn²⁺ to Eu²⁺. The energy transfer probability from Mn²⁺ to Eu²⁺ depends strongly on the Mn²⁺ concentration, which is maximized at a Mn²⁺ concentration of 3 mol%. It drastically decreases for higher concentrations. The results indicated that SrSi₂O₂N₂:Eu²⁺, Mn²⁺ is a promising green-emitting phosphor for white-light emitting diodes with near-UV LED chips.     

Tuning the luminescence color and enhancement of afterglow properties of Sr(4−x−y)CaxBayAl14O25:Eu,Dy phosphor by adjusting the composition

Color point tuning is an important challenge for improving the practical applications of various displays, especially there are very limited white color single hosts that emits in the white spectrum. In this paper, the possibility of color tuning by substituting part of host lattice cation (Sr²⁺ ions) by Ca²⁺ or Ba²⁺ ions in an efficient strontium aluminate phosphor, Sr₄Al₁₄O₂₅:Eu²⁺,Dy³⁺, is reported and found to be very promising for displays. A detail study by replacing part of Sr²⁺ with Ca²⁺ or Ba²⁺ has been investigated. X-ray diffraction study showed that crystal structure of Sr₄Al₁₄O₂₅ is preserved up to 20 mol of Ca²⁺ ion exchange while it is limited to 10 mol of Ba²⁺ ions exchange. Substantial shift in the emission band and color were observed by substitution of Sr²⁺ by Ca²⁺ or Ba²⁺ ions. A bluish-white emission and afterglow was observed at higher Ca²⁺ ions substitution. Further, partial Ca²⁺ substitutions (up to 0.8 mol) resulted in enhanced afterglow of Sr₄Al₁₄O₂₅:Eu²⁺,Dy³⁺ phosphor. However, Ba²⁺ substitution decreased the fluorescence as well afterglow of the Sr₄Al₁₄O₂₅:Eu²⁺,Dy³⁺ phosphor significantly. The enhanced phosphorescence by partial Ca²⁺ substitution is explained on the basis of increased density of shallow traps associated with higher solubility of Dy³⁺ ions in to the host lattice due to equivalent size of Ca²⁺ and Dy³⁺ ions. Thus, Ca²⁺ substitution in the Sr₄Al₁₄O₂₅:Eu²⁺,Dy³⁺ phosphor is a promising method for tuning the emission color and improving the afterglow intensity of the phosphor.     

Synthesis of monodisperse spherical core-shell SiO2-SrAl2Si2O8: Eu2+ phosphors by hydrothermal homogeneous precipitation method

Nanocrystalline SrAl₂Si₂O₈ :Eu²⁺ phosphor layers were coated on nonaggregated, monodisperse and spherical SiO₂ particles using a hydrothermal homogeneous precipitation. After annealing at 1100 °C, core-shell SiO₂@SrAl₂Si₂O₈ :Eu²⁺ particles were obtained. They were characterized with x-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy and photoluminescence techniques. XRD analysis confirmed the formation of SiO₂ @SrAl₂Si₂O₈ :Eu²⁺ particles; it indicated that the SrAl₂Si₂O₈ :Eu²⁺ shells on SiO₂ particles consisted of hexagonal crystallites. The core-shell phosphors obtained are well-dispersed submicron spherical particles with a narrow size distribution. The thickness of the coated layer is approximately 20–40 nm. Under ultraviolet excitation (361 nm), the particles emit blue light at about 440 nm due to the Eu²⁺ ions in their shells.     

Photoluminescence properties of RE-activated Na3GdP2O8 (RE = Tb, Dy, Eu, Sm) under VUV excitation

RE³⁺-activated monoclinic Na₃GdP₂O₈ (RE³⁺ = Tb³⁺, Dy³⁺, Eu³⁺, Sm³⁺) phosphors have been synthesized by a solid-state reaction method. Their photoluminescence properties in the vacuum ultraviolet (VUV) region were investigated. By analyzing their excitation spectra, the host-related absorption band was determined to be around 166 nm. The f-d transition bands and the charge transfer bands for Na₃GdP₂O₈:RE³⁺ (RE³⁺ = Tb³⁺, Dy³⁺, Eu³⁺, Sm³⁺) were assigned and corroborated. For the sample Na₃GdP₂O₈:5%Tb³⁺, the strong bands at around 202 and 221 nm are assigned to the 4f-5d spin-allowed transitions and the weak band at 266 nm is related to the spin-forbidden transition of Tb³⁺. For Na₃GdP₂O₈:5%Dy³⁺, the broad band at 176 nm could be related to the f-d transitions of Dy³⁺ and the O²⁻ → Dy³⁺ charge transfer band (CTB) besides the host-related absorption. In the excitation spectrum of Eu³⁺ doped sample, the O²⁻ → Eu³⁺ CTB is observed to be at 245 nm. For the Sm³⁺ doped sample, the O²⁻ → Sm³⁺ CTB is not distinguished obviously and is overlapped with the host-related absorption band.     

The blue-light emission enhancement mechanism of Eu in Eu, Dy: SiO2 matrix

A Eu, Dy co-doped SiO₂ matrix xerogel with blue emission was prepared by the sol–gel method. Strong blue emission located between 425 nm and 525 nm with a peak at 486 nm is observed under UV laser excitation at room temperature, which is related to a 4f → 5d energy transition of Eu²⁺. Such techniques as FT-IR and TGA–DSC were used to measure the microstructure of the luminescent materials. The influence of Dy³⁺ ions on the luminescent property of Eu²⁺ was investigated. The emission intensity of Eu, Dy-codoped samples is stronger than that of Eu doped samples. The emission enhancement mechanism relating to Eu²⁺ is attributed to an energy transfer involving Dy³⁺ → Eu²⁺. Using energy transition theory, we speculate that the mechanism may be one of the resonance transfers via multi-polar interactions, and present a possible energy transfer model. The Eu²⁺ blue emission intensity reaches the maximum when the Dy³⁺ concentration is 0.1 mol%. When the concentration of Dy³⁺ is 0.3 mol%, a fluorescence quenching appears which might be related to the overlap part of Eu²⁺ excitation and emission levels, and also suggests the existence of Eu²⁺ → Eu²⁺ energy transfer.     

Sr3.5Mg0.5Si3O8Cl4: Eu bluish-green-emitting phosphor for NUV-based LED

Sr₄Si₃O₈Cl₄:Eu²⁺ and Sr_3.5Mg_0.5Si₃O₈Cl₄:Eu²⁺ phosphors were prepared by a conventional solid state reaction (SS). Excited by 370 nm near-ultraviolet light, the phosphors show an efficient bluish-green wide-band emission centering at 484 nm, which originates from the 4f5d¹ → 4f⁷ transition of Eu²⁺ ion. The excitation spectra of the phosphors are a broad band extending from 250 nm to 400 nm. Mg²⁺-codoping greatly enhances the bluish-green emission of the phosphors. An LED was fabricated by coating the Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ phosphor onto an ~ 370 nm-emitting InGaN chip. The LED exhibits bright bluish-green emission under a forward bias of 20 mA. The results indicate that Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ is a candidate as a bluish-green component for fabrication of NUV-based white LEDs.     

Effects of Zn doping on the structural and luminescent properties of Sr4Si3O8Cl4:Eu phosphors

Sr₄Si₃O₈Cl₄: Eu²⁺ phosphors were synthesized by the solid-reaction at high temperature. The emission intensity reaches a maximum at 0.08 mol% of Eu²⁺ concentration. The present paper mainly focused on the effects of Zn²⁺ on the crystallization behavior and photoluminescence (PL) properties of Sr₄Si₃O₈Cl₄:0.08Eu²⁺. Results suggested that no new phase is introduced by co-doping with a small amount of Zn²⁺ ions, but when co-doped with excessive amount of Zn²⁺ ions, Sr₂ZnSi₂O₇ appears. We find that the co-doping of a small amount of Zn²⁺ could remarkably improve the PL intensity of Sr₄Si₃O₈Cl₄:0.08Eu²⁺. When x = 0.05, the intensity of Sr₄Si₃O₈Cl₄:0.08Eu²⁺,xZn²⁺ was increased up to 2.3 times that of pure Sr₄Si₃O₈Cl₄:0.08Eu²⁺, which could be attributed to the flux effect of Zn²⁺ ions, and the Zn²⁺ doping reduces the opportunities of the energy transfer between Eu²⁺.     

The effect of Sb2O5 additions on the dielectric properties of Ag(Nb0.8Ta0.2)O3 ceramics

The sintering behavior and dielectric properties for perovskite Ag(Nb_0.8Ta_0.2)O₃ ceramic with Sb₂O₅ doping was explored. A small amount of Sb₂O₅ (2.5 wt.%) led to high densification at temperatures < 1060 °C. The dielectric constant increased and the temperature coefficient decreased with increasing concentration of Sb₂O₅, and the dielectric constant reached 673, combined with a low temperature coefficient of 147 ppm/°C, and dielectric loss of 0.0044 (at 1 MHz) for the sample with 3.5 wt.% Sb₂O₅ sintered at 1080 °C.     

Combusion synthesis,structural and photo-physical characteristics of Eu<Superscript>2+</Superscript> and Dy<Superscript>3+</Superscript> co-doped SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> phosphor nanopowders

In this research, we reported the synthesis of Eu²⁺ and Dy³⁺ co-doped SrAl₂O₄ phosphor nanopowders with high brightness and long afterglow by urea-nitrate solution combustion synthesis (SCS) at 600 °C, followed by heating the resultant combustion ash at 1,200 °C in a weak reductive atmosphere (5% H₂ + 95% N₂). The broad-band UV-excited luminescence of the SrAl₂O₄: Eu²⁺, Dy³⁺ nanopowders was observed at λ _max = 517 nm due to transitions from the 4f⁶5d¹ to the 4f⁷ configuration of the emission center (Eu²⁺ ions). The excitation spectra consist of 240- and 254 nm broad peaks. Finally, it was found that the optimum ratio of urea is 2.5 times higher than theoretical quantities for the best emission condition of SrAl₂O₄: Eu²⁺, Dy³⁺ phosphor nanopowders.     

Luminescence properties of Ba2LiB5O10:Dy phosphor

A novel warm white phosphor Ba₂LiB₅O₁₀:Dy³⁺ with various Dy³⁺ concentrations was synthesized by the conventional solid-state reaction at 800 °C. The crystal structure of the phosphor was characterized by X-ray diffraction (XRD). The photoluminescence properties of Ba₂LiB₅O₁₀:Dy³⁺ were investigated, and the critical concentration of the activator ion (Dy³⁺) was found to be 0.04 mol per formula unit. Under the ultraviolet excitation of 348 nm, the phosphor presented warm white luminescence with dominating emissions at 484.6 and 577 nm, corresponding to ⁴F_9/2-⁶H_15/2, ⁴F_9/2-⁶H_13/2 transitions, respectively. The chromatic properties of the typical sample Ba₂LiB₅O₁₀:0.04Dy³⁺ phosphor have been found to have chromaticity coordinates of x = 0.31 and y = 0.35.     

Enhancement of fatigue endurance and retention characteristic in Bi3.25Eu0.75Ti3O12 thin films

The effects of moderate annealing temperature (600–800 °C) on the microstructure, fatigue endurance, retention characteristic, and remnant polarization (2P_r) of Bi_3.25Eu_0.75Ti₃O₁₂ (BET) thin films prepared by metal-organic decomposition (MOD) were studied in detail. 2P_r (66 µC/cm² under 300 kV/cm), fatigue endurance (3% loss of 2P_r after 1.2 × 10¹⁰ switching cycles), and retention characteristic (no significant polarization loss after 1.8 × 10⁵s) for BET thin film annealed at 700 °C are better than those for thin films annealed at other temperature. The mechanisms concerning the dependence of microstructure and ferroelectric properties on the annealing temperature were discussed.     

A yellow-emitting Ca3Si2O7: Eu phosphor for white LEDs

A series of yellow-emitting phosphors based on a silicate host matrix, Ca_3 − xSi₂O₇: xEu²⁺, was prepared by solid-state reaction method. The structure and photoluminescent properties of the phosphors were investigated. The XRD results show that the Eu²⁺ substitution of Ca²⁺ does not change the structure of Ca₃Si₂O₇ host and there is no impurity phase for x < 0.12. The SEM images display that phosphors aggregate obviously and the shape of the phosphor particle is irregular. The EDX results reveal that the phosphors consist of Ca, Si, O, Eu and the concentration of these elements is close to the stoichiometric composition. The Ca_3 − xSi₂O₇: xEu²⁺ phosphors can be excited at a wavelength of 300-490 nm, which is suitable for the emission band of near ultraviolet or blue light-emitting-diode (LED) chips. The phosphors exhibit a broad emission region from 520 to 650 nm and the emission peak centered at 568 nm. In addition, the shape and the position of the emission peak are not influenced by the Eu²⁺ concentration and excitation wavelength. The phosphor for x = 0.045 has the strongest excitation and emission intensity, and the Ca_3 − xSi₂O₇: xEu²⁺ phosphors can be used as candidates for the white LEDs.     

Persistent luminescence of Eu and Dy doped barium aluminate (BaAl2O4:Eu,Dy) materials

Polycrystalline Eu²⁺ and Dy³⁺ doped barium aluminate materials, BaAl₂O₄:Eu²⁺,Dy³⁺, were prepared with solid state reactions at temperatures between 700 and 1500 °C. The influence of the thermal treatments on the stability, homogeneity and structure as well as to the UV-excited and persistent luminescence of the materials was investigated by X-ray powder diffraction, SEM imaging and infrared spectroscopies as well as by steady state luminescence spectroscopy and persistent luminescence decay curves, respectively. The IR spectra of the materials prepared at 250, 700, and 1500 °C follow the formation of BaAl₂O₄ composition whereas the X-ray powder diffraction of compounds revealed how the hexagonal structure was obtained. The morphology of the materials at high temperatures indicated important aggregation due to sintering. The luminescence decay of the quite narrow Eu²⁺ band at ca. 500 nm shows the presence of persistent luminescence after UV irradiation. The dopant (Eu²⁺) and co-dopant (Dy³⁺) concentrations affect the crystallinity and luminescence properties of the materials.     

Luminescence properties of Eu ions doped in Y2−xGdxO3 thin films grown by pulsed laser deposition method

Luminescence properties of Y_2−xGd_xO₃:Eu³⁺ (x = 0 to 2.0) thin films are investigated by site-selective laser excitation spectroscopy. The films were grown by pulsed laser deposition method on SiO₂ (100) substrates. Cubic phase Y₂O₃ and Gd₂O₃ and monoclinic phase Gd₂O₃ are identified in the excitation spectrum of the ⁷F₀ → ⁵D₀ transition of Eu³⁺. The emission spectra of the ⁵D₀ → ⁷F_J (J = 1 and 2) transition from individual Eu³⁺ centers were obtained by tuning the laser to resonance with each excitation line. The excitation line at around 580.60 nm corresponds to the line from Eu³⁺ with C₂ site symmetry of cubic phase. New lines at 578.65 and 582.02 nm for the C_S sites of Gd₂O₃ with monoclinic phase are observed by the incorporation of Gd in Y₂O₃ lattice. Energy transfer occurs between Eu³⁺ ions at the C_S sites and from Eu³⁺ ions at the C_S sites to those at the C₂ site in Y_2−xGd_xO₃.     

Luminescence properties of Dy-doped Li2SrSiO4 for NUV-excited white LEDs

A series of single-phase full color phosphors, Dy³⁺-doped Li₂SrSiO₄ was synthesized by a solid-state reaction method. The phase of the as-prepared powders was measured by X-ray diffraction pattern (XRD) and the chemical composition was characterized using energy dispersive spectroscopy (EDS). The luminescent properties of Li₂SrSiO₄:Dy³⁺ were systematically investigated by concentration quenching, decay behavior and thermal stability measurements. The results suggested that the emission intensity of the Li₂SrSiO₄:Dy³⁺ was much stronger than that of Li₂SrSiO₄:Eu²⁺. It was worth to mention that Li₂SrSiO₄:Dy³⁺ phosphor possessed excellent thermal stability for use in light-emitting diodes (LEDs) and the emission intensity measured at 300 °C was only decreased 8% comparing with that measured at room temperature. Furthermore, the Commission International del’Eclairage (CIE) chromaticity coordinates of Li₂SrSiO₄:Dy³⁺ moved toward the ideal white light coordinates (0.33, 0.33). All results demonstrated that Li₂SrSiO₄:Dy³⁺ might be a potential phosphor for NUV-based white light-emitting diodes.     

Synthesis and characterization of nanocrystalline manganese pyrophosphate Mn2P2O7

Mn₂P₂O₇ polyhedral particles were synthesized by simple and cost-effective method using manganese nitrate hydrate and phosphoric acid in the presence of nitric acid with further calcinations at the temperature of 800 °C. The crystallite size obtained from X-ray line broadening is 31 ± 13 nm for the Mn₂P₂O₇. The X-ray diffraction and SEM results indicated that the synthesized nanoparticles have only the structure without the presence of any other phase impurities. The FT-IR and FT-Raman spectra show characteristic bands of the P₂O₇⁴⁻ anion. The UV–Vis–NIR spectrum confirms the octahedral coordination of Mn²⁺ ion.