Modern Problems of Intensification of Heat Exchange in Channels

The current achievements in the field of intensification of heat exchange in tube heatexchange apparatus are considered. Requirements for highefficiency heattransfer surfaces have been formulated. Problems of intensification of heat exchange in bundles of finned tubes and in heatexchange apparatus under conditions of condensation and boiling of heattransfer agents and under scaling conditions have been investigated. Highefficiency designs of heatexchange apparatus are presented.     

On the “scientometric decline” of British science. One additional graph in reply to Ben Martin

With respect to the issue of whether the scientometric measurement of the decline of British science is an artifact of the specific database and underlying assumptions in methods, I argue that there are fewer analytical objections against measurement by usingSciSearch Online than against other methods (based on the fixed journal set and fractional counting). The measurement of international co-authorship, i.e. a network indicator, should not be confounded with measurement of performance of a single nation. The time series for the different subsets of UK-publications, which have been proposed, are given. None of the indicators can be shown to exhibit a trend (in contrast to a drift). The hypothesis of a decline has therefore to be rejected.     

Standard Gibbs' energies of formation of BaCuO2, Y2Cu2O5 and Y2BaCuO5

The Gibbs' energies of formation of BaCuO₂, Y₂Cu₂O₅ and Y₂BaCuO₅ from component oxides have been measured using solid state galvanic cells incorporating CaF₂ as the solid electrolyte under pure oxygen at a pressure of 1.01×10⁵ Pa BaO + CuO BaCuO₂ G _f,ox ^o (± 0.3) (kJ mol^–1)=–63.4–0.0525T(K) Y₂O₃ + 2CuO Y₂Cu₂O₂ G _f,ox ^o (± 0.3) (kJ mol^–1)=18.47–0.0219T(K) Y₂O₃ + BaO + CuO Y₂BaCuO₅ G _f,ox ^o (± 0.7) (kJ mol^–1)=–72.5–0.0793T(K) Because the superconducting compound YBa₂Cu₃O_7– coexists with any two of the phases CuO, BaCuO₂ and Y₂BaCuO₅, the data on BaCuO₂ and Y₂BaCuO₅ obtained in this study provide the basis for the evaluation of the Gibbs' energy of formation of the 1-2-3 compound at high temperatures.     

The age hardening effect in Ti-6 Al-4 V due to ω and α precipitation in the β grains

The structure at room temperature of a quenched TA6V titanium alloy has been investigated. This structure is + or + according to the treatment temperature; it is always metastable. During ageing the grains decomposed by the reaction + + +; this decomposition was accompanied by a large increase of the 0.2% yield stress. No structural modification was observed in. The and phase of TA6V were separately investigated in the form of single-phase alloys. The hardness of was insensitive to ageing, while was considerably hardened by and; we deduced that the strengthening of the minor phase during ageing is mainly responsible for the hardening of TA6V.     

γ ? α2 Phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%)

The ₂ phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%) alloy has been studied by analytical electron microscopy. ₂ and phases were found at grain boundaries. ₂ layers that suspended in layers and interfacial ledge higher than 2d ₍₁₁₁₎ at /₂ interfaces were observed in the lamellar grains. These facts indicated that ₂ phase transformation and dynamic recrystallization have occurred during high temperature stress rupture deformation. It can be concluded that deformation induced ₂ phase transformation and dynamic recrystallization resulted in the presence of particles at grain boundaries. A structural and compositional transition area between deformation-induced ₂(or ) and its adjacently original (or ₂) phases was found by HREM and EDS and is suggested as a way to transform between and ₂ phase during high temperature stress rupture deformation. The transition area was formed by slide of partial dislocations on close-packed planes and diffusion of atoms.     

Temperature field in a plate containing a system of heat sources

The temperature field is determined in a circular plate with a system of thin extrinsic heat sources.Notation T temperature in the plate with the inclusions - r polar radius - polar angle - time - (r,) coefficient of thermal conductivity - (r,) heat transfer coefficient - C(r,) volume heat capacity - W(r,, ) specific intensity of the heat sources - half thickness of the plate - (x) Dirac's delta function - ¯T finite Fourier cosine transform of the temperature - p parameter for this transformation - T Laplace transform of the temperature - s its parameter - Iv(x) Bessel function with imaginary argument of order - K _v (x) the MacDonald function of order - and dimensionless temperature - Po Pomerantz number - Bi Biot number - Fo Fourier's number - dimensionless polar radius - b₁ ^* dimensionless radius of the circle on which the inclusions are placed - R^* dimensionless radius of the plate Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 40, No. 3, pp. 495–502, March, 1981.     

The Interplay of Electronic and Nuclear Magnetism in PtFe x at Milli-, Micro-, and Nanokelvin Temperatures

We have measured ac susceptibility, nuclear magnetic resonance, and nuclear heat capacity of two PtFe _x samples with concentrations of magnetic impurities x = 11 ppm and 41 ppm at magnetic fields (0 ± 0.05) mTB248 mT. The susceptibility data have been measured at temperatures of 0.3 KT100 mK, no hint for nuclear magnetic ordering could be detected to a temperature of 0.3 K. The nuclear heat capacity data taken at 1.4 KT10 mK show enhanced values which scale with x at low polarization. This effect is described by a model assuming an internal magnetic field caused by the impurities. No indication for nuclear magnetic ordering could be detected to 1.4 K. The nuclear magnetic resonance experiments have been performed on these samples at 0.8 KT0.5 mK and 2.5 mTB22.8 mT as well as on three other samples with x = 5, 10, 31 ppm in a different setup at 40 KT0.5 mK and at 5.4 mTB200 mT. Spin-lattice and effective spin-spin relaxation times ₁and ₂ ^* of ¹⁹⁵ Pt strongly depend on x and on the external magnetic field. No temperature dependence of ₁and ₂ ^* could be detected and the NMR data, too, give no hint for nuclear magnetic ordering to 0.8 K.     

Shear viscosity of the B phase of superfluid3He

The shear viscosity (T) in the Balian-Werthamer (BW) state of superfluid ³ He is calculated variationally throughout the region 0t 1(t=T/T _c) from the transport equation for Bogoliubov quasiparticles. Coherence factors are treated exactly in the calculation of the collision integral. The numerical result for =_s= _s(T)/_n(T_c) agree very well with experiment in the range 0.8t1.0. Analytic expressions = 0.577 (1–1.0008t) and =1–(23/64) [=(T)/k _B T] are obtained in the low-temperature region and in the vicinity ofT _c, respectively. From the numerical analysis it is shown that the latter equation is valid only in the temperature range 0.9997t1.0.Supported by the Research Institute for Fundamental Physics, Kyoto University.     

Calculating the hydraulic characteristics of two-phase-helium circulation systems

An approximate analytical solution is obtained for calculating the pressure drop in the flows of a boiling two-phase liquid in a heated channel. The dependence of the maximum temperature in the channel on the rate of flow of the cryogenic fluid is determined.Notation c_p isobaric heat capacity - d diameter - F lateral surface of channel - f surface of channel cross section - G mass velocity of liquid - q external heat flux to a unit of the channel length - i enthalpy (i -enthalpy of the liquid on the saturation line) - L channel length - l length of boiling section - P pressure - P pressure drop - P_f pressure drop in the boiling section - r heat of vaporization - T temperature - T_h effective temperature - v specific volume of liquid - v specific volume of saturated vapor - x mass content of vapor - z coordinate - friction coefficient - coefficient of local fluid resistance in the single-phase section Indices 0, 2 parameters corresponding to the outlet and inlet cross sections of the channel - 1 parameters corresponding to the beginning of boiling of the liquid - s equilibrium parameters Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 396–401, September, 1981.     

Evidence for collective excitations in superconducting tin whiskers

Based on the assumption that a phase-slip center in a clean quasi-one-dimensional superconductor excites a collective oscillation, the time-averaged value of the electrochemical potential of quasiparticles is calculated. At larger distances from the phase-slip center, swings below (or above) the electrochemical potential _p of the Cooper pairs. This makes it possible to understand the unexpected results of previous measurements.     

Investigation of energy-gap anisotropy in superconducting aluminum,cadmium, and zinc

Measurements of the low-temperature specific heat of the pure metal and dilute nonmagnetic alloys of Al, Cd, and Zn are described. The washing out of the energy gap anisotropy with increasing impurity as predicted by Anderson was observed in aluminum-magnesium alloys, and the mean-squared anisotropy parameter a ² was measured to be a ²0.010. Values deduced from measurements on Zn and Cd and their corresponding alloys with 1₀ gave a ²0.02 for Zn and a ²0.05 for Cd. Values of the gaps determined by fitting to a two-gap model are given and compared to those deduced from previous work.     

Heat transfer and critical heat fluxes in the boiling of aqueous solutions of polyethylene oxide at reduced pressures under natural-convection conditions

Experimental data are presented on heat transfer and critical heat fluxes in the boiling of aqueous solutions of polyethylene oxide of different concentrations under conditions of natural convection at atmospheric and reduced temperatures.Notation q heat flux - q_cr critical heat flux - q_cr.s critical heat flux during boiling under subheating conditions - T overheating of heating surface relative to-saturation temperature - T_S subheating of liquid core to the saturation temperature - heat-transfer coefficient - P pressure - , densities of the liquid and vapor - c_p isobaric specific heat of water - r heat of vaporization Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 47, No. 1, pp. 24–28, July, 1984.     

Spin hydrodynamic equations with external disturbances and suitable Green's functions for superfluid3He-B. New onsager relations

The spin hydrodynamic equations for superfluid³He-B have been obtained for the case of external, time-dependent fields. On the basis of a microscopic approach, expressions are found for additional terms in equations containing these fields. Considering the linear response of the system to the switching on of external fields, formulas are found for suitable Green's functions (magnetization-magnetization, rotation-rotation, magnetization-rotation, rotation-magnetization). The rotation-rotation Green's function has the 1/q ² singularity characteristic of superfluid systems. Connections between Green's functions lead to relations among kinetic coefficients v, ₁, and ₂. It is also shown that there is a conserved quantityQ ^(B) = div v _s ^(B) that describes sources or magnetic type charges (monopoles) of the superfluid velocity v _s ^(B) . Comparison with the phenomenological approach suggests thatQ ^(B) is proportional to a pseudoscalar giving the projection of the spin density onto the vector describing the axis of rotation.     

Two shift theorems leading to lower bounds to eigenvalues

Summary Two theorems are proved by which the other bound can be obtained from the Rayleigh quotient, i.e., the bound which cannot be obtained by the Rayleigh-Ritz method.The method presented here utilizes a shift operation which is the redistribution of weight functions in the Rayleigh quotient.     

Relationship between deposition and recrystallization textures of copper and chromium electrodeposits

The 100, 111 and 110 textures of copper electrodeposits obtained from copper sulfate baths changed to the 100, 100 and textures, respectively, after recrystallization. The textures of chromium electrodeposits obtained from the standard Sargent bath remained unchanged after recrystallization. The results are in agreement with the prediction of the strain energy release maximization model, in which the recrystallized grains orient themselves so that their minimum elastic modulus direction can be parallel to the absolute maximum internal stress direction due to dislocations in the non-recrystallized grains.     

Natural damped frequencies and axial response of a rotating finite viscous liquid column

Summary For a finite solidly rotating cylindrical liquid column the damped natural axisymmetric frequencies have been determined. The liquid was considered incompressible and viscous. The cases of freely slipping edges and that of anchored edges have been treated. It was found that instability appears in a purely aperiodic root for the spinning liquid bridge. This is in contrast to the instability appearing in the damped oscillatory natural frequency of a nonspinning liquid column at . The spinning viscous liquid column exhibits the same instability as the frictionless liquid. It appears at for axisymmetric oscillations.List of symbols a radius of liquid column - I _m modified Bessel function of first kind and orderm - s complex frequency ( ) - r, ,z polar cylindrical coordinates - p pressure - t time - u, v, w radial-, azimuthal- and axial velocities of liquid, respectively - Weber number - h height of liquid column - dynamic viscosity of liquid - v kinematic viscosity of liquid (v=/) - density of liquid - surface tension of liquid - _r , _rz shear stress - (r, z, t) circulation - (r, z, t) streamfunction - ₀ angular velocity of liquid column about the axis of symmetry - (,t) free surface displacement     

Modes of “normal” and “deteriorated” heat exchange in the single-phase near-critical region in the turbulent flow of helium in tubes

The results of a study of heat transfer to helium in the single-phase near-critical region are presented. The boundaries of existence of the modes of normal and deteriorated heat exchange are established. A calculating dependence for the local heat exchange is proposed.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 30, No. 4, pp. 606–612, April, 1976.     

Surface Heat Treatment of Facing and Other Materials with Concentrated Solar Energy

Surface treatment of building materials, ornamental ceramics, covercoat enamels, blastfurnace and openhearth slags, and natural stones of the basalt type has been carried out with the use of solar furnaces and their simulators for the purpose of obtaining protectivedecorative vitreous and glazed coatings. The specific energy consumption and the optimum heat fluxes necessary to obtain highquality coatings have been determined. The results of searching investigations testify to the fact that renewable environmentally safe concentrated solar energy can be utilized in industry and the national economy for surface heat treatment of different materials by melting them in the air.     

Radiofrequency size-effect measurements of the electron scattering frequency in cadmium

Precise parallel- and tilted-field radiofrequency size-effect measurements of the temperature dependence of the electron scattering frequency v(T) have been made on symmetric orbits on the first-, second-, and third-band Fermi surface sheets in samples with normals 11\-20 and 10\-10. The limiting point measurements on the third-band lens near 0001 provide the clearest evidence for a T ² contribution to v(T) that is the right order of magnitude for electron-electron scattering in cadmium. In parallel field measurements on orbits on the first and second bands (including a broken orbit) we find v(T) T ² + T ³. On these orbits the values for are 5–20 times larger than for the limiting point and other orbits on the third band. The temperature dependence of v(T\> 2 K) on extremal, limiting point, and open orbits on the second- and third-band Fermi surface sheets can be well accounted for by a simple plane wave model for electron-phonon intersheet scattering. This contribution to v(T) turns on approximately as exp (–T _t /T) above T _t /10, where T _t is the minimum gap temperature on the orbit for intersheet scattering by quasi-transversely polarized phonons. The fitted gap temperatures as well as the other parameters of the plane wave model agree well with the known dimensions of the Fermi surface of cadmium. While clear evidence is lacking, we note that this intersheet scattering model can also be used to explain the large T ² coefficients obtained for the first- and second-band orbits, where, in fact, one has gap temperatures T _t smaller than 1 K.Supported by the Fonds National Suisse de la Recherche Scientifique.     

Some simple flows of a Johnson-Segalman fluid

Summary Unlike most other fluid models, the Johnson-Segalman fluid allows for a non-monotonic relationship between the shear stress and rate of shear in a simple shear flow for certain values of the material parameter. This has been used for explaining a phenomenon such as spurt. Here, we study three simple flows of a Johnson-Segalman fluid with a view towards understanding its response characteristics. We find that boundary conditions can have a very interesting effect on the regularity of the solution; changing them continuously leads to solutions that change their regularity. First, we consider the flow through a circular pipe and find solutions that have discontinuous velocity profiles which have been used to explain the phenomenon of spurt (cf. [10], [11]). Second, we consider the flow past an infinite porous plate and show that it will not admit solutions which have discontinuous velocity gradients, the solutions being necessarity smooth. Lastly, we study Poiseuille flow in a concentric annulus with porous boundaries. While spurt could be explained alternatively by allowing for stick-slip at the wall, the Johnson-Segalman model seems particularly suited in describing the appearance of shear-layers (cf. [13]).