钨合金材料动态拉伸性能与微观断裂机制关系的研究

测定了光滑和缺口钨合金材料在不同应变率下动态拉伸性能的变化规律，观察了材料断裂的微观机制。结果发现，光滑试样具有正应变率效应，缺口试样具有负应变率效应，在不同应变率下，两种试样的断裂方式没有明显的差别。     

钨合金材料的动态拉伸实验研究

采用旋转盘式间接杆-杆型冲击拉伸装置(SHTB)对颗粒度分别为2, 5μm和20μm的三种91%(质量分数)细化钨合金材料在动态冲击载荷作用下的力学性能进行了实验研究,分析了三种钨合金在应变率为0.001, 200, 500s-1时动态力学性能,给出了颗粒度大小与材料屈服强度的关系;采用扫描电子显微镜(SEM)对动态拉伸实验中回收的试件断口进行断口分析,研究钨合金在不同应变率状态下材料的破坏特征,在动态拉伸载荷作用下钨合金材料呈现出一种混合破坏模式包括钨颗粒的劈裂以及颗粒与基体界面的开裂.     

不同晶粒度钨合金动态力学性能研究

采用拉格朗日实验分析技术对1～3μm,10～15μm和30～40μm三种不同晶粒度细化钨合金材料91W-6.3Ni-2.7Fe在高应变率下的动态力学性能进行研究.得到三种不同晶粒度的钨合金在不同冲击速度下各拉氏位置的应力时程曲线.利用拉氏分析方法对钨合金在高应变率下的力学性质进行探讨,分析各拉氏位置的应变,比容,密度,应变率,比内能,质点速度等物理量的变化历史,讨论不同晶粒度尺寸对钨合金在高应变率下动态力学性能的影响,给出钨合金在应变率为104～105s-1时的应力应变曲线.     

钨合金动态力学性能的三维数值模拟研究

采用数值模拟的方法对钨合金在冲击载荷作用下的动态力学响应进行了研究。运用有限元动力分析程序建立了具有典型微观结构钨合金三维有限元单胞模型,对钨合金在拉伸载荷作用下的动态力学性能进行了数值模拟研究,分析了应变率对其力学性能的影响,给出了不同应变率条件下单胞模型的应力和应变分布云图,在与实验结果对比的基础上验证了该有限元模型的可靠性。     

砂浆材料SHPB实验及惯性效应的数值模拟研究

进行了砂浆材料在不同应变率下的SHPB实验,拟合实验数据得到了动态强度放大因子DIF随应变率变化的关系曲线。基于实验测得应变率时程曲线,采用简化有限元模型,对实验进行了数值模拟。该文探讨了动态压缩实验中惯性效应产生的原因,并基于数值模拟对本实验中惯性效应对材料动态强度的影响进行了剥离,得到了砂浆材料动态强度放大因子随应变率变化的固有特性曲线,并将该固有特性曲线作为数值模拟中应变率效应的输入,计算结果与实验得到的应力-应变曲线吻合较好。进一步通过比较输入CEB推荐曲线和已有半经验公式的模拟结果,验证了所提出砂浆材料动态强度放大因子固有特性曲线的优越性。     

数值模拟中混凝土类材料应变率效应曲线的惯性效应修正

数值模拟是研究混凝土类材料在动载下响应的有效方法,准确输入材料真实的应变率效应曲线对预测结构在动载下的响应有重要作用。收集了1990年以来针对混凝土类材料的动态抗压实验数据,并将惯性效应对材料动态强度的影响进行剥离,得到真实的材料应变率效应引起的抗压动态强度放大因子(DIF?(5))与应变率对数的关系曲线。分析数据发现:实验得到的抗压动态强度放大因子(DIFs)和惯性效应引起的抗压动态强度放大因子(DIFi)都随试件尺寸的增大而增大;随着材料准静态强度增大,混凝土类材料DIFi随应变率增长的增长幅度减小。对比拟合曲线与其他曲线可知,在高应变率下,新的应变率效应拟合曲线比已有半经验公式能更好地反映实验数据的DIF?(5);模拟时分别输入新的应变率效应曲线和CEB推荐公式,将输出结果与DIFs对比,验证了新的应变率效应曲线的优越性。     

钨及钨合金的研发和应用现状

介绍了钨及钨合金材料的研究进展及动向,包括纯化技术、细化研究、强韧化研究、复合材料的研究等,并对当前研究较多的钨合金材料,主要是耐震钨丝、纳米钨合金、钨电极材料、钨基复合材料等的制备工艺、合金性能及应用开发现状进行了阐述.     

一种考虑应变率效应的结构非线性时程分析方法

提出了一种在非线性时程分析中考虑材料应变率效应的近似方法：首先,对结构进行不考虑应变率效应的非线性时程分析;然后,根据第一次分析的结果可以得到关键位置在与结构最大顶点位移对应的前1/4循环内的平均应变率,根据这些点的平均应变率对进入非线性构件材料的本构关系进行修正;最后,对结构进行第二次分析。文中给出了该方法的力学解释,并通过数值模拟对该方法进行了验证。结论：本文提出的方法具有较高的精度,可以作为一种在非线性时程分析中考虑应变率效应的有效方法。     

钨合金细观参数对其宏观屈服强度的影响

通过细观分析,给出钨颗粒相的形状、组分和两相力学参数对钨合金宏观屈服强度的影响.其中,钨颗粒看作基体上的夹杂,在小变形条件下假设钨颗粒仅发生弹性变形,而钨合金的宏观屈服强度决定于基体相的屈服强度.在该假设基础上,利用Eshelby方法及Mori-Tanake平均应力概念计算分析了不同钨合金材料,特别是不同变形量工艺处理的钨合金材料的宏观屈服强度,计算结果与实验结果基本一致.     

纯钛高应变率拉伸力学行为的实验研究

利用MTS809材料试验机和旋转盘式间接杆杆型冲击拉伸实验装置,对多晶纯钛进行了室温环境下应变率为0.001,0.01s-1的准静态和300,1400s-1的动态拉伸实验,获得了纯钛等温和绝热拉伸应力-应变曲线;实施了应变率为300s-1的冲击拉伸复元实验,获得了纯钛在高应变率下的等温应力-应变曲线。结果表明:纯钛的拉伸力学行为具有明显的应变硬化效应、应变率强化效应和绝热温升软化效应。采用修正的KHL模型较好地表征了纯钛在准静态和动态实验应变率范围内的拉伸力学行为。     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.     

Investigation of the Corrosion Behaviors of HVOF-Sprayed Carbide Cernet Coatings in Molten Al-Zn-Si Alloy Bath

In continuous hot-dip galvanization process the corrosion and chemical stability of the sink roll in the galvanizing bath are important problem which effects on the quality and productivity. In order to protect the sink roll the carbide cermet and/or ceramic coatings were deposited on the surface of the sink roll. The WC-, Cr3 C2-cermet coatings were deposited by high velocity oxygen fuel (HVOF) spray, respectively. The coating samples were immersed in molten Zn-alloy containing 50 wt % aluminum at 833 K for 24 hr and 144 hr, respectively. The inter-diffusion and inter-reaction of Zn, Al and elements in coating and corrosion behaviors of these coatings were investigated by XRD, SEM and EPMA etc. The corrosion mechanisms of the carbide cermet coatings and ceramic coatings in molten High Al-Zn-alloy were approached.     

Fundamental study of adhesion of ice to cooling solid surface (Discussion on influence of copper oxide layer on ice adhesion force)

In many situations, ice often adheres to a cooling solid surface, frequently causing serious accidents. It is critical to clarify the mechanism of ice adhesion to the cooling surface in order to prevent ice adhesion. In a past study, the shearing stresses of two kinds of test plates with a copper surface having the higher thermal conductivity were measured. The shearing stress corresponds to ice adhesion force. Both shearing stresses were significantly different; however, the cause remains unclear.Therefore, the present study focuses on an oxide layer as the main factor causing the difference of both shearing stresses; the influence of the oxide layer formed on shearing stress was discussed. And in the removal and reformation processes of the oxide layer, the time variation of the shearing stress was clarified. Moreover, the relationship between the state of the copper surface and the shearing stress was also clarified by surface analysis.     

重塑标准推行格局 推动LED照明的普及（英文）

正When you are enjoying the green,energy-saving and healthy lighting of IKEA LED luminaire,you may not realize that most of IKEA’s LED bulbs are produced by the LED luminaire smart manufacturing system of Hangzhou Zhongwei Photoelectricity CO.,LTD(ZVISION).No longer enclosed in the laboratory,the product standards are brought into the factory workshop and even to the entire production process.Thus,the standards are promoted and applied in a favorable way by enterprises,benefitting consumers with high quality products.     

Chinese Experts Contribute to ISO＇s New Toy Standards

正The international standard,ISO 8124-6,Safety of toys–Part 6:Certain phthalate esters in toys and children’s products,was officially issued by ISO worldwide on August 15.It was the first time for Chinese experts to lead the ISO standard development in toys industry.The standard was drafted by a group of Chinese experts from SAC/TC for toys and relevant Chinese departments and finally completed by a dedicated international group of experts.ISO 8124-6 makes a substantive breakthrough in the aspects of the scope of toys,limitation of plasticizer types,control of test cost,accuracy of test,operation convenience,etc.,offering the operational guidance for toy manufactures and testing laboratories.     

中国质量(北京)大会(英文)

正Themed on"quality,innovation,development",the first China Quality Conference(Beijing)was held in the Great Hall of the People on September 15.Chinese Premier Li Keqiang delivered an important speech at the conference.State Councilor Yang Jing and Wang Yong attended the conference with over 600 domestic and international representatives from foreign,regional and international quality organizations     

National Working Meeting on Land and Resources Standardization

正The National Working Meeting on Land and Resources Standardization was held in Beijing on July 15,2014.Wang Min,the Deputy-Minister of the Ministry of Land and Resources,and Yin Minghan,the Chief-Engineer of SAC addressed the meeting.Representatives from relevant competent departments and technical committees were present.The meeting aims to summarize work,discuss existing problems and make clear working thoughts,promoting standardization work of land and resources to a new level.Wang Min pointed out that the standardization work of land and resources should be centered on the basic principles of"protecting land and resources dutifully,intensively and economically utilizing land and resources,and making all-out efforts to safeguard the public’s rights and interests",highlighted the