新型电解质材料[BMIM]ClO3离子液体的合成及其物化性能

以N-甲基咪唑为原料合成了室温离子液体1-丁基-3-甲基咪唑氯酸盐([BMIM]ClO3),用IR、NMR、DSC-TGA等手段对产物进行了表征,测定了相关物化性能,如密度、表面张力、黏度、电导率和电化学窗口等,并考察了该离子液体的溶剂性能。结果表明,该离子液体作为新型的电解质材料,具有低黏度、高电导率,密度、表面张力、黏度均随温度升高而减小,电导率随温度升高而增大,与温度符合Arrhenius方程。该离子液体与多数常规溶剂互溶,并对某些金属氧化物具有较高的溶解度,为离子液体在选矿、电解金属氧化物等方面的应用奠定了基础。     

固体有机物合成的低温共熔溶剂的研究及其对纤维素的溶解

对固体有机物尿素、己内酰胺、乙酰胺以不同配比制备的尿素/己内酰胺、尿素/乙酰胺和乙酰胺/己内酰胺3种低温共熔溶剂进行了研究,并考察了其物理化学性质(熔点、电导率等).结果表明,随着物质的量比的不同,低共熔溶剂的熔点不同,最佳物质的量比分别为1∶3、1∶2和1∶1,在最佳物质的量比下的熔点分别为30℃、48℃和18℃.低温共熔溶剂的电导率在10-4～10-5 S/m数量级,随温度的升高,电导率增加,电导率与温度符合Arrhenius方程.IR测试结果显示,固体有机物各自分子内的氢键消失,形成了新的氢键.初步探讨了纤维素在3种体系中的溶解性能,结果显示,3种溶剂对纤维素有一定的溶解能力.通过分析得出,该类共熔体溶剂为酰胺类溶剂,主要通过其羰基上的氧原子和氨基上的氮原子与纤维素上的羟基形成氢键.IR和XRD测试结果表明,纤维素和再生纤维素有相似的结构,但纤维素的晶型从Ⅰ型转变为Ⅱ型.     

六氟磷酸盐吡啶离子液体的合成及电导率研究

采用二溴丁烷和3-甲基吡啶(物质的量之比为1.0∶2.2)为原料,以异丙醇为溶剂,温度控制在70～80℃,反应4～6h,得到吡啶溴盐离子液体。用吡啶溴盐与六氟磷酸盐发生置换反应,搅拌反应4h,得到六氟磷酸盐吡啶离子液体。测定了[C4(MPy)2][PF6]2离子液体在有机溶剂中的电导率;及离子液体在不同溶剂、不同浓度、不同温度下的电导率。结果表明:溶液的电导率随着温度升高而增大;随着浓度的增大而增大。相同温度、浓度下,乙腈的电导率最大;环丁砜的电导率最小。     

烯丙基咪唑离子液体的合成与溶液性能

室温离子液体氯化1-烯丙基-3-甲基咪唑被合成,利用质谱和NMR对其结构进行了表征。该离子液体与水或乙醇的二相混合液在293.2K的粘度被测定并计算了该混合体系的过量粘度,建立了过量粘度与水或乙醇的摩尔分数的关系。另外,电导率随组分及温度的变化以及电导活化能也被测定,溶液的电导率随温度的升高及溶剂量的增加而增大。     

微波辐射下离子液体［RMIm］PF6（R=P, B, C6）的合成及其电导率研究

在微波辐射下,1-甲基咪唑分别与有机卤盐（1-溴丙烷、1-溴丁烷、1-溴己烷）在80℃回流加热10min,可制得咪唑类离子液体的中间体溴代1-丁基-3-甲基咪唑（[BMIm]Br）、溴代1-丙基-3-甲基咪唑（[PMIm]Br）、溴代1-己基-3-甲基咪唑（[C6MIm]Br）,进一步与HPF6在室温搅拌反应4h,制得憎水性的咪唑类离子液体[BMIm]PF6,[PMIm]PF6和[C6MIm]PF6。对这3种离子液体及其在不同有机溶剂如丙酮、甲醇、乙酸乙酯中的电导率进行测定,发现离子液体的电导率受咪唑上取代基种类、溶剂种类、浓度和温度的影响,取代基的链越长,体积越大,离子液体的电导率越小。并且随温度升高和浓度的增大,离子液体的电导率也增大。     

离子液体与水的混合体系中尼龙6的解聚反应

在150℃～230℃条件下,以氯化1-丁基-3-甲基咪唑离子液体与水组成的二元混合体系为介质进行尼龙6的解聚研究。固相残余物利用红外光谱和差示扫描量热仪进行分析。液相产物通过液相色谱-质谱联用仪和液相色谱进行定性与定量分析。建立了反应温度(A)、混合体系中离子液体的物质的量分数(B)以及反应时间(C)与ε-己内酰胺回收率(Y)之间的数学模型:Y(%)=43.76+6.69A+6.06B+3.60C+3.15AB+3.48AC-17.06A2-16.56B2-14.18C2,并利用响应曲面法(RSM)确定了解聚的优化工艺条件,即反应温度175℃、离子液体的物质的量分数14.2%及反应时间7.3h,此时ε-己内酰胺的回收率为44.4%、尼龙6的降解率为88.4%。     

添加剂对Urea-ZnCl2离子液体电沉积锌的影响

本文研究了添加剂LiCl、NaCl、KCl对Urea-ZnCl2离子液体物理化学性能及其对电沉积锌的影响。结果表明:在Urea-ZnCl2离子液体中添加LiCl、NaCl、KCl可降低体系的熔点、提高体系的电导率,而且电导率随碱金属阳离子半径的增大而升高,在低碳钢上恒电位沉积,LiCl、NaCl、KCl的加入可提高沉积层质量,使得沉积颗粒细化,沉积层更加致密均匀。     

离子液体法溶解纤维素制备碳纤维

采用离子液体1,3-二甲基咪唑磷酸二甲酯盐[MMIM]~+[MMP]~-对纤维素进行溶解,并在衍生过程加入碳化助剂来提高碳纤维的碳化产率,利用流变仪、傅里叶红外光谱仪和场发射扫描电镜研究了纤维素/[MMIM]~+[MMP]~-混合液体的剪切粘度、纤维素(衍生物)薄膜的电阻率和电导率及碳化纤维的直径变化。结果表明,纤维素衍生物膜碳化产率以及排放气体的最佳取代度是P含量为1.6%(质量分数);碳纤维的电导率随碳化温度升高而增大,主要因为碳化温度升高导致样品中的碳纤维含量升高,从而造成样品的石墨化程度升高,电导率升高,最佳碳化温度为900℃;离子液体法制备的碳纤维直径分布均匀、表面光滑且碳纤维之间几乎没有相互缠绕粘结的现象,独立性较高。     

Urea-ZnCl2离子液体中电沉积Zn-Ti合金

本文研究了TiCl4对Urea-ZnCl2离子液体体系电化学行为的影响。结果表明：TiCl4的加入能够提高Urea-ZnCl2离子液体的电导率,促进钛以Zn-Ti合金的形式沉积。在铜基体上进行恒电位沉积,可获得均匀致密的Zn-Ti合金层,且晶粒尺寸随沉积温度的升高而增大。     

磺酸基功能化离子液体中水杨酸系列酯的合成研究

合成了6种Brφnsted酸性离子液体,以其作为催化剂,用于水杨酸酯的合成中.实验结果表明,所选离子液体对水杨酸乙酯的合成都具有较高的催化活性,其中[HSO3-pmim][OTf]的催化效果最好.以[HSO3-pmim][OTf]为催化剂,考察酸醇物质的量比、反应时间、反应温度及离子液体的用量对酯化率的影响.最佳实验条...     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.     

Investigation of the Corrosion Behaviors of HVOF-Sprayed Carbide Cernet Coatings in Molten Al-Zn-Si Alloy Bath

In continuous hot-dip galvanization process the corrosion and chemical stability of the sink roll in the galvanizing bath are important problem which effects on the quality and productivity. In order to protect the sink roll the carbide cermet and/or ceramic coatings were deposited on the surface of the sink roll. The WC-, Cr3 C2-cermet coatings were deposited by high velocity oxygen fuel (HVOF) spray, respectively. The coating samples were immersed in molten Zn-alloy containing 50 wt % aluminum at 833 K for 24 hr and 144 hr, respectively. The inter-diffusion and inter-reaction of Zn, Al and elements in coating and corrosion behaviors of these coatings were investigated by XRD, SEM and EPMA etc. The corrosion mechanisms of the carbide cermet coatings and ceramic coatings in molten High Al-Zn-alloy were approached.     

Fundamental study of adhesion of ice to cooling solid surface (Discussion on influence of copper oxide layer on ice adhesion force)

In many situations, ice often adheres to a cooling solid surface, frequently causing serious accidents. It is critical to clarify the mechanism of ice adhesion to the cooling surface in order to prevent ice adhesion. In a past study, the shearing stresses of two kinds of test plates with a copper surface having the higher thermal conductivity were measured. The shearing stress corresponds to ice adhesion force. Both shearing stresses were significantly different; however, the cause remains unclear.Therefore, the present study focuses on an oxide layer as the main factor causing the difference of both shearing stresses; the influence of the oxide layer formed on shearing stress was discussed. And in the removal and reformation processes of the oxide layer, the time variation of the shearing stress was clarified. Moreover, the relationship between the state of the copper surface and the shearing stress was also clarified by surface analysis.     

重塑标准推行格局 推动LED照明的普及（英文）

正When you are enjoying the green,energy-saving and healthy lighting of IKEA LED luminaire,you may not realize that most of IKEA’s LED bulbs are produced by the LED luminaire smart manufacturing system of Hangzhou Zhongwei Photoelectricity CO.,LTD(ZVISION).No longer enclosed in the laboratory,the product standards are brought into the factory workshop and even to the entire production process.Thus,the standards are promoted and applied in a favorable way by enterprises,benefitting consumers with high quality products.     

Chinese Experts Contribute to ISO＇s New Toy Standards

正The international standard,ISO 8124-6,Safety of toys–Part 6:Certain phthalate esters in toys and children’s products,was officially issued by ISO worldwide on August 15.It was the first time for Chinese experts to lead the ISO standard development in toys industry.The standard was drafted by a group of Chinese experts from SAC/TC for toys and relevant Chinese departments and finally completed by a dedicated international group of experts.ISO 8124-6 makes a substantive breakthrough in the aspects of the scope of toys,limitation of plasticizer types,control of test cost,accuracy of test,operation convenience,etc.,offering the operational guidance for toy manufactures and testing laboratories.     

中国质量(北京)大会(英文)

正Themed on"quality,innovation,development",the first China Quality Conference(Beijing)was held in the Great Hall of the People on September 15.Chinese Premier Li Keqiang delivered an important speech at the conference.State Councilor Yang Jing and Wang Yong attended the conference with over 600 domestic and international representatives from foreign,regional and international quality organizations     

National Working Meeting on Land and Resources Standardization

正The National Working Meeting on Land and Resources Standardization was held in Beijing on July 15,2014.Wang Min,the Deputy-Minister of the Ministry of Land and Resources,and Yin Minghan,the Chief-Engineer of SAC addressed the meeting.Representatives from relevant competent departments and technical committees were present.The meeting aims to summarize work,discuss existing problems and make clear working thoughts,promoting standardization work of land and resources to a new level.Wang Min pointed out that the standardization work of land and resources should be centered on the basic principles of"protecting land and resources dutifully,intensively and economically utilizing land and resources,and making all-out efforts to safeguard the public’s rights and interests",highlighted the