Effect of ascorbic acid on the pitting resistance of 316L stainless steel in synthetic tap water

This study examined the effect of L-ascorbic acid (A.A) concentration on the pitting corrosion properties of 316L stainless steel (316L STS) of heat exchanger in synthetic tap water containing 400 ppm of Cl- ion. The pitting corrosion of 316L STS can be effectively inhibited by the 10^-4 M of A.A concentration. In this condition, the adsorption of A.A reinforced the passive film of steel by blocking the Cl^- ions at the active site. However, the passive film was deteriorated and severe pitting corrosion occurred above the 10^-4 M of A.A concentration. Above the 10^-4 M of A.A concentration, A.A generates soluble chelate rather than absorbs on the steel surface and it causes passive film deterioration and severe pitting corrosion. The critical ratio, which is a critical ratio of surface coverage of aggressive to inhibitive ion necessary to initiate localized corrosion, calculated 2.93 up to the 10^-4 M. It has approximately 2.93:1 ratio of the coverage of local Cl^- ions to A.A. Above the critical ratio, the pitting corrosion will occur with degradation of the passive film. On the other hands, above the 10^-4 M A.A concentration caused a negative effect because the heat energy for adsorption is increased.     

点缺陷模型在2205双相不锈钢中的应用

采用电化学极化曲线和电化学阻抗技术对2205双相不锈钢在0.1%、1.0%及3.5%（质量分数,%）三种不同浓度的NaCl溶液中的腐蚀性能进行测试,采用点缺陷模型(PDM)对测试结果进行建模与分析。研究结果表明,2205双相不锈钢随着溶液浓度的升高抗点蚀能力下降,这是由于在钝化膜的生长过程中,氧离子缺陷产生于金属/膜界面,消耗于膜/溶液界面,而金属离子缺陷产生于膜/溶液界面,消耗于金属/膜界面;氧离子缺陷的迁移导致钝化膜的生长,而金属离子缺陷的迁移使得钝化膜发生溶解。同时,根据PDM模型理论并从金属相角度出发对2205不锈钢建立钝化膜溶解模型,可知2205双相不锈钢奥氏体相γ上的钝化膜可能比铁素体相α优先发生溶解。     

Corrosion behavior of Cu/Al casting-rolled clad plates in different alkaline solution

The effect of pH value and different kinds of anions on the corrosion behavior of Cu/Al casting-rolled clad plates in the alkaline solution was evaluated by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), weight loss analysis, 3D confocal laser scanning microscopy (CLSM) and electrochemical test. Results show the corrosion mainly occurs on the aluminum side. The corrosion resistance of the Cu/Al decreases as the pH value increases. When pH≥12, the dissolution of the film layer is faster than the passivation process. The addition of Cl⁻ ions reduces the corrosion resistance of the Cu/Al clad plates, which leads to pitting corrosion. The higher the concentration of Cl⁻ ions, the more prone the pitting to occur. The addition of SO₄²⁻ ions causes the denudation of the samples. The corrosion resistance of the Cu/Al is better in the alkaline solution containing NO₃⁻ ions than that in the solution containing Cl⁻ ions or SO₄²⁻ ions. When adding SO₄²⁻, NO₃⁻ and Cl⁻ to the pure alkaline solution, the corrosion resistance of the Cu/Al clad plates decreases.

     

Pitting corrosion behaviour of 2101 duplex stainless steel in chloride solutions

ABSTRACT

The corrosion behaviour of 2101 duplex stainless steel (DSS) in NaCl solution was studied and compared with that of 2205 DSS. The effects of chloride concentration and solution temperature on pitting corrosion behaviour were focused. The relative sensitivity to pitting corrosion of the constituent phases in both 2101 and 2205 DSSs was also explored. Pitting corrosion susceptibility was evaluated by conducting cyclic polarisation curve measurement. The corrosion morphology was examined by a scanning electron microscope equipped with energy dispersive spectrometer. The experimental results showed that the pitting corrosion resistance of 2101 DSS was inferior to that of 2205 DSS by exhibiting a lower threshold chloride concentration and a lower critical pitting temperature. For both 2101 and 2205 DSSs, the ferrite phase was more susceptible than austenite phase to pitting corrosion.

This paper is part of a supplementary issue from the 17th Asia-Pacific Corrosion Control Conference (APCCC-17).     

Role of alloyed copper on corrosion resistance of austenitic stainless steel in H2S–Cl− environment

Corrosion test, surface analysis and thermodynamic calculation were carried out in the H₂S–Cl⁻ environments to clarify the role of alloyed Cu on the corrosion resistance of austenitic alloys. The alloyed Cu improved pitting corrosion resistance in the H₂S–Cl⁻ environment. The surface film of Cu-containing alloy indicated double layer consists of copper sulfide and chromium oxide, and the copper sulfide was able to exist stably compared to iron sulfide and nickel sulfide. It is concluded that the copper sulfide would enhance the formation of chromium oxide film which improve the pitting corrosion resistance in the H₂S–Cl⁻ environment.     

Initiation and Inhibition of Pitting Corrosion in Alkali Solutions under potentiostatic polarization conditions

The variation of the critical pitting potential of a zincalloy was studied in aerated NaOH solutions as a function of the concentration of the aggressive ions, Cl^?, Br^? and I^?. Curves with segmented nature were obtained when E_pitting was plotted versus logarithm of the halogen ion concentrations. Initiation of pitting corrosion was discussed on the basis of formation of complex halo-compounds with the oxides/hydroxides that constitute the passive surface film. Addition of chromate, phosphate and carbonate ions to the halogen-containing solutions causes the shift of the critical pitting potential in the noble direction, accounting for increased resistance to pitting attack. Nitrite-ion additions contribute with the halogen ions in the destruction of the passive film. Sufficient concentrations of the carbonate ions cause complete inhibition of pitting corrosion.     

Effects of coolant chemistry on corrosion of 3003 aluminum alloy in automotive cooling system

In this work, effects of coolant chemistry, including concentrations of chloride ions and ethylene glycol and addition of various ions, on corrosion of 3003 Al alloy were investigated by electrochemical impedance spectroscopy measurements and scanning electron microscopy characterization. In chloride‐free, ethylene glycol–water solution, a layer of Al‐alcohol film is proposed to form on the electrode surface. With the increase of ethylene glycol concentration, more Al‐alcohol film is formed, resulting in the increase in film resistance and charge‐transfer resistance. In the presence of Cl^? ions, they would be involved in the film formation, decreasing the stability of the film. In 50% ethylene glycol–water solution, the threshold value of Cl^? concentration for pitting initiation is within the range of 100 ppm to 0.01 M. When the ethylene glycol concentration increases to 70%, the threshold Cl^? concentration for pitting is from 0.01 to 0.1 M. In 100% ethylene glycol, there is no pitting of 3003 Al alloy even at 0.1 M of Cl^?. Even a trace amount of impurity cation could affect significantly the corrosion behavior of 3003 Al alloy in ethylene glycol–water solution. Addition of Zn²⁺ is capable of increasing the corrosion resistance of Al alloy electrode, while Cu²⁺ ions containing in the solution would enhance corrosion, especially pitting corrosion, of Al alloy. The effect of Mg²⁺ on Al alloy corrosion is only slight.     

Inhibition effect of chromate on the passivation and pitting corrosion of a duplex stainless steel in LiBr solutions using electrochemical techniques

The electrochemical behavior of duplex stainless steel (DSS) in LiBr media was investigated by anodic cyclic polarization curves and AC impedance measurements. The effect of bromide concentration and the presence of chromate in the solutions on the corrosion behavior of AISI 2205 was studied. Cyclic polarization curve analyses showed that there was different pitting susceptibility of passive films depending on the LiBr concentration. Pitting potential decreases with LiBr concentration in a semilogarithmic scale following two different slopes. Chromate presence displaces pitting potentials towards more positive values at low LiBr concentrations but it has no effect when LiBr concentration increases.The comparative analysis carried out in LiBr and LiBr chromate-containing solutions at two different concentrations, 0.016 M and 0.032 M, verifies the assumption that halogen ions facilitate inhibitor adsorption. The addition of halides strongly increased the inhibition efficiency of chromate. The passive film becomes more resistant when bromide concentration increases, although film thickness decreases.     

The effect of chromate in the corrosion behavior of duplex stainless steel in LiBr solutions

The electrochemical behavior of duplex stainless steel (DSS) in LiBr media was investigated by anodic cyclic polarization curves and AC impedance measurements. The effect of bromide concentration and chromate presence in the solutions on the corrosion behavior of DSS was studied. It was found, by cyclic polarization curves analyses, that there was different pitting susceptibility of passive films formed on DSS depending on the chromate/bromide ratio: pitting corrosion susceptibility highly decreased from a chromate/bromide ratio lower than 0.01.The comparative investigations carried out in LiBr and LiBr + 0.032Li₂CrO₄ verify the assumption that the halide ions facilitate inhibitor adsorption. The addition of halides increased inhibition efficiency to a considerable extent. Passive film becomes more resistant when bromide concentration increases, although film thickness decreases.     

2205和316L不锈钢在氢氟酸中的电化学腐蚀行为

通过动电位极化和电化学阻抗方法考察了2205双相不锈钢和316L不锈钢在5%(体积分数)HF溶液中的电化学行为,借助Mott-Schokkty曲线分析了两种不锈钢表面钝化膜的半导体特性。结果表明：两种不锈钢在氢氟酸溶液中都能发生钝化,且2205双相不锈钢的钝化区间范围更宽,维钝电流密度更低。2205双相不锈钢表面钝化膜表现出更高的钝化膜电阻和电荷转移电阻,其抗氢氟酸腐蚀性能优于316L不锈钢,这主要与2205双相不锈钢中的Mo和Cr含量高、表面钝化膜缺陷少、钝化膜易修复等因素有关。     

The Microstructure and Pitting Resistance of Weld Joints of 2205 Duplex Stainless Steel

2205 duplex stainless steel (DSS) was welded by submerged arc welding. The effects of both heat input and groove type on the ferrite/austenite ratio and elemental diffusion of weld joints were investigated. The relationships among welding joint preparation, ferrite/austenite ratio, elemental diffusion, and pitting corrosion resistance of weld joints were analyzed. When the Ni content of the weld wire deposit was at minimum 2–4% higher than that of 2205 DSS base metal, the desired ratio of ferrite/austenite and elemental partitioning between the austenite and ferrite phases were obtained. While the pitting sensitivity of weld metal was higher than that of base metal, the self-healing capability of the passive film of weld metal was better than that of the base metal when a single V-type groove was used. Furthermore, the heat input should be carefully controlled since pitting corrosion occurred readily in the coarse-grained heat-affected zone near the fusion line of welded joints.     

The influence of different aggressive anions on the electrochemical behaviour of aluminium in sodium nitrate aqueous solutions

The effects of different experimental parameters influencing the determination of critical pitting and protection potentials of aluminium and its alloys have been studied by potentiostatic and potentiodynamic methods. The resistance of aluminium against corrosion in aqueous media can be attributed to a rapidly formed surface oxide film. The addition of the aggressive anions like: chloride, thiocyanide, hydroxyl, sulphide, formate, and acetate (Cl⁻, SCN⁻, OH⁻, S²⁻, HCOO⁻ and CH₃‐ COO⁻) lead to extensive localized attack in all of the cases. The breakdown of the passive film takes into account the migration of aggressive anions through the film. Breakdown occurs when aggressive anions reach the metal‐film interface. E_π is the critical pitting potential, E_p ist the protection potential and the pitting can be formed only in the E_π–E_p polarization range as it was proved in many experiments [1–3]. The most likely action mechanism of aggressive anions is not a complete dissolution of the film, nor penetration of aggressive anions through solid oxide as suggested for nickel and iron [4]. It is more likely to be somewhere in between the two i.e. action of aggressive anions is that of complexing aluminium ions and pulling in water to hydrate the layer in a way similar to that occurring at cathodic hydrogen evolution, where such dramatic increase of hydrogen evolution rate is observed after a certain cathodic potential is reached. Localized corrosion can be prevented by the action of adsorptive inhibitors which prevent the adsorption of the aggressive anions or by the formation of a more resistant oxide film on the metal surface. The corrosion mechanism is not modified by the addition of ammonium rhodanide but only slowed down.     

Mg-15Li合金在碱性NaCl溶液中的腐蚀行为

    用电化学方法研究了Mg-15Li合金在碱性NaCl溶液中的腐蚀行为.结果表明：在强碱性pH=13及扫描电镜环境下,当Cl^-浓度低于0.4 mol/L时,合金表面形成稳定的钝化膜;随Cl^-浓度增加,点蚀电位逐渐降低.     

Passivity and passivity breakdown of zinc anode in alkaline medium

The electrochemical behaviour of zinc in NaOH solutions has been investigated by using potentiodynamic technique and complemented by X-ray analysis. The E/i curves exhibit active, passive and transpassive regions prior to oxygen evolution. The active region displays two anodic peaks. The passivity is due to the Formation of a compact Zn(OH)₂ film on the anode surface. The transpassive region is assigned to the electroformation of ZnO₂. The reverse sweep shows an activation anodic peak and one catholic peak prior to hydrogen evolution. The influence of increasing additives of NaCl, NaBr and Nal on the anodic behaviour of zinc in NaOH solutions has been studied. The halides stimulate the active dissolution of zinc and tend to break down the passive film, leading to pitting corrosion. The aggressiveness of the halide anions towards the stability of the passive film decreases in the order: I^? > Br^? > Cl^?. The susceptibility of zinc anode to pitting corrosion enhances with increasing the halide ion concentration but decreases with increasing both the alkali concentration and the sweep rate.     

2205双相不锈钢在酸性H2S环境下的应力腐蚀行为及开裂机理研究

_{摘要:采用C型环实验研究了2205双相不锈钢在饱和H2S环境下的应力腐蚀行为及开裂机理。研究结果表明,2205双相不锈钢在NACE标准A溶液中有良好的抗应力腐蚀能力。通过OM}、_{SEM、EDS及电化学手段分析得出2205双相不锈钢的应力腐蚀开裂经历了表面点蚀,蚀坑形成,H2S解离,H原子吸附并从蚀坑位置扩散进入金属基体,在金属基体中聚集,通过氢致开裂机制导致裂纹萌生,并逐渐扩展。}     

Atmospheric corrosion monitoring of a weathering steel under an electrolyte film in cyclic wet–dry condition

Electrochemical Impedance Spectroscopy (EIS) and film thickness measurements have been employed to study the corrosion monitoring of steel under an electrolyte film in wet–dry cycles simulating a coastal atmosphere. The results indicate that within each cycle, the corrosion rate increases during drying process due to an increase in Cl⁻ concentration and an enhancement of oxygen diffusion by thinning out of the electrolyte. As corrosion process proceeds, the corrosion rate increases greatly and reaches a maximum. During subsequent corrosion stage, the corrosion rate decreases greatly and keeps at a low value due to the formation of a stable rust layer.     

pH与温度对2205DSS在盐卤中的孔蚀行为影响研究

利用电化学方法、交流阻抗技术、失重法及金相显微术研究了pH与温度变化对2205DSS在盐卤中耐孔蚀行为的影响.结果表明：随着卤水pH值的增大,2205DSS耐孔蚀性能先略微增强、然后减弱;根据实际制盐工艺条件,卤水的pH值应适当控制在8.7或8.8以内;随温度升高,2205DSS基体抵抗孔蚀能力明显下降;试样在盐卤水介质中的电极反应是不可逆的,其腐蚀反应既受活化极化控制,又受溶液扩散控制.     

The nature of the copper sulfide film grown on copper in aqueous sulfide and chloride solutions

In this paper, the properties of copper sulfide films formed both anodically and naturally in deaerated/anoxic aqueous sulfide and chloride solutions were investigated using a series of electrochemical and surface analytical techniques. A combination of cyclic voltammetric, corrosion potential (E_corr), and cathodic stripping voltammetric experiments showed that the sulfide film growth kinetics and film morphologies were controlled by the supply of SH⁻ from the bulk solution to the copper surface. There was no passive barrier layer observed on the copper surface under either electrochemical or corrosion conditions. The film morphology was dependent on the type and concentration of anions (SH⁻, Cl⁻) present in the solution. Scanning electron microscopy on both surfaces and focused ion beam-cut cross-sections showed the growth of a thin, but porous, base layer of chalcocite (Cu₂S) after short immersion periods (up to 2 hr) and the continuous growth of a much thicker crystalline outer deposit over longer immersion periods (≥36 hr), suggesting a solution species transport-based film formation process and the formation of an ineffective thin “barrier-type” layer on copper.     

真空度对2205双相钢在热浓缩海水中点蚀行为的影响

目的研究真空度对2205双相不锈钢在海水淡化环境中耐点蚀性能的影响。方法在1.5倍人工浓缩海水中,采用循环阳极极化曲线与电化学阻抗谱等电化学方法,研究了2205双相不锈钢的点蚀和再钝化行为,并通过扫描电子显微镜对极化后试样的腐蚀形貌进行分析。结果测试了七种不同真空状态下2205双相不锈钢的循环阳极极化曲线和电化学阻抗谱,发现随着真空度的升高,试样的自腐蚀电位和点蚀电位均不断降低,分别约从-256 m V和605 m V下降到-485 m V和363 m V(均vs.SCE),点蚀倾向明显增大。同时,Nyquist曲线中的半圆弧逐渐变得扁平,Bode图中的相位角约从80°下降到77°,但是点蚀电位与再钝化电位之差逐渐升高。不同真空度下循环阳极极化后,试样表面的点蚀坑形貌不完全相同,蚀坑数量随着真空度的升高而明显减少,当真空度升高为0.72时,点蚀坑尺寸明显减小。结论随着真空度的逐渐升高,不锈钢钝化膜的致密性和保护性降低,电化学阻抗值逐渐减小,耐点蚀性能变差,但是再钝化性能却有所增强。循环阳极极化后试样的腐蚀程度减小。     

On the Initiation process of pitting corrosion on austenitic stainless steel in chloride solutions

A literature survey has lead to the conclusion that a theory which postulates an increased anodic reactivity on a local site in the passive film is very probable. Experiments have been set up to confirm these suggestions. By means of the electron-microanalyser, it is shown that CI^?ions are preferentially adsorbed at singular points at the metal surface before the stage that pits can be observed. It has also been demonstrated that pH changes occur at local areas during the induction period. These two observations indicate that corrosion already occurs during the induction period. Induction time measurements have shown that the induction time is not very reproducible. The quantity of transferred charge per initiated pit before the breakdown of the film is redly a better re- producible figure. From this, the quantity of Cl^?ions necessary to create an active site is calculated. Experiments with the static potential band method reveal that pits can initiate at any potential higher than the pitting potential. Growing pits can repassivate at any potential. A model for the initiation is given. The pitting corrosion process starts with adsorption of chloride ion at singular points, mainly local stress points. The local anodic current density will be higher and in this way favourable conditions (low pH, high Cl^?concentration) are created for the formation of a local site in the metal surface free of a passivating film The creation of those conditions is an autocatalytic process. The time required to form those favourable electrochemical conditions corresponds with the observed induction period. The migration of activating ions and the occurring pH change at a singular point must exceed a critical rate, otherwise passive film stabilizing effects will dominate. This model for the pitting corrosion supports the acid theory and links this theory with the peptization theory.