Surface modification of spherical LiNi1/3Co 1/3 Mn1/3O2 with Al2O3 using heterogeneous nucleation process

To improve the cycle stability at high voltage and high charge/discharge rate, spherical LiNi1/3Co1/3Mn1/3O2 was coated with Al2O3 by using heterogeneous nucleation process, and the physical and electrochemical properties were studied. The SEM images show that there is a uniform coating on the modified spherical LiNi1/3Co1/3Mn1/3O2. The electrochemical tests indicate that the properties of LiNi1/3Co1/3Mn1/3O2 coated with 0.5% aluminum oxide are the best. The initial capacities are 150 and 173 mA.h/g at the rate of I C in the voltage range of 2.7-4.3 V and 2.7-4.6 V, respectively, and the discharge capacities maintain about 99% and 85% after 30 cycles, respectively. While those of the bare LiNi1/3Co1/3Mn1/3O2 are only 90% and 75%, respectively. The CV tests of LiNi1/3Co1/3Mn1/3O2 show that Al203-coating can restrain the oxide-reduction peak currents fading during the charge/discharge course.     

Al2O3包覆LiNi0.03Co0.05Mn1.92O4正极材料的制备及其电化学性能

以Al(NO3)3?9H2O为包覆原料，通过燃烧法制备得到LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料。通过X射线衍射(XRD)，场发射扫描电子显微镜(FESEM)和透射电镜(TEM)等表征手段对材料的结构和形貌进行分析，并通过恒电流充放电、循环伏安(CV)、交流阻抗(EIS)等测试分析材料的电化学性能。结果表明，Al2O3包覆没有改变LiNi0.03Co0.05Mn1.92O4的尖晶石型结构，包覆层厚度约10.6nm。LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料电化学性能得到了明显改善，1 C和10 C倍率下初始放电比容量分别为119.9 mAh?g-1和106.3 mAh?g-1，充放电循环500次后容量保持率分别为88.4%和78.2%，而未包覆的LiNi0.03Co0.05Mn1.92O4在1 C和10 C倍率下初始放电比容量分别为121.2 mAh?g-1和104.0 mAh?g-1，500次循环后容量保持率分别为84.1%和67.6%。LiNi0.03Co0.05Mn1.92O4@Al2O3活化能为32.92 kJ?mol-1，而未包覆材料的活化能为36.24 kJ?mol-1，包覆有效降低了材料Li+扩散所需克服的能垒，提高了材料的电化学性能。     

锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2的制备及性能研究

采用溶胶-凝胶法制备了锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2,并考察了烧结温度对材料结构、表面形貌和电化学性能的影响.XRD和SEM测试结果表明,900℃下烧结得到的样品是粒径在0.3～0.5 μm范围的球形粒子,具有最佳的阳离子有序度;充放电测试结果表明,其在0.1C倍率下首次放电容量达到148.8...     

Si4+和F-掺杂对LiNi1/3Co1/3Mn1/3O2结构和电化学性能的影响

以Li2CO3、NiO、Co2O3、MnO2、LiF和SiO2为原料,采用机械力活化固相法制备了Si4+和F-掺杂的锂离子电池正极材料LiNi1/3Co 1/3Mn1/3O2.通过X射线衍射(XRD)、扫描电镜(SEM)和电化学性能测试等技术研究了LiNi1/3Co1/3Mn1/3O2的结构特征、形貌及电化学性能等.结...     

Effects of synthesis conditions on the structural and electrochemical properties of layered LiNi1/3Co1/3Mn1/3O2 cathode material via oxalate co-precipitation method

The uniform layered LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries was prepared by using (Ni1/3Co1/3Mn1/3)C2O4 as precursor synthesized via oxalate co-precipitation method in air. The effects of calcination temperature and time on the structure and electrochemical properties of the LiNi1/3Co1/3Mn1/3O2 were systemically studied. XRD results revealed that the optimal calcination conditions to prepare the layered LiNi1/3Co1/3Mn1/3O2 were 950°C for 15 h. Electrochemical measurement showed that the sample prepared under the such conditions has the highest initial discharge capacity of 160.8 mAh/g and the smallest irreversible capacity loss of 13.5% as well as stable cycling performance at a constant current density of 30 mA/g between 2.5 and 4.3 V versus Li at room temperature.     

Preparation and electrochemical characteristics of CO3（PO4）2-coated LiNi0.8Co0.2O2 by solid-state reaction at room temperature

LiNi0.8Co0.2O2 particles were modified by Co3（PO4）2 coating. The effects of the Co3（PO4）2 coating on the structure and electrochemical properties of the LiNi0.8Co0.2O2 cathode material were investigated. The Co3（PO4）2 coating forms a thin layer on the surface of the LiNi0.8Co0.2O2 material and a solid solution by interacting with the LiNi0.8Co0.2O2 core material during calcination at 700℃ for 4 h. Charge-discharge experiment results show that the Co3（PO4）2 coating improves the cycling stability of the LiNi0.8Co0.2O2 cathode material. The capacity retention of the pristine LiNi0.8Co0.2O2 cathode after 50 cycles is 83.6%, whereas it is 91.7% in the case of the LiNi0.8Co0.2O2 cathode coated with 1 wt.% Co3（PO4）2. Storage tests of the 4.35 V charged electrode at 60℃ after a month show that the Co3（POg）2-coated sample exhibits good storage properties compared with the pristine sample.     

Synthesis and electrochemical characterization of layered Li[Ni1/3CO1/3 Mn1/3]O2 cathode material for Li-ion batteries

1 INTRODUCTIONDue to the high cost of LiCoO2,a commonlyused cathode material in commercial rechargeablelithium-ion batteries , much efforts have been madeto develop cheaper cathode materials than LiCoO2,Li Ni O2and Li MnO2have been studied extensivelyas possible alternatives to LiCoO2[1 4 ]. Stoichio-metric Li Ni O2is knownto be difficult to synthesizeandits multi-phase reaction during electrochemicalcyclingleads to structural degradation,andlayeredLi MnO2has a significant drawback…     

前处理工艺对Li[Ni1/3Mn1/3Co1/3]O2正极材料结构、形貌和电化学性能的影响（英文）

以[Ni1/3Co1/3Mn1/3]3O4和氢氧化锂为原料,分别采用球磨法和液相法前处理工艺制备层状正极材料Li[Ni1/3Mn1/3Co1/3]O2。采用X？射线衍射（XRD）、场发射扫描电镜（FESEM）、恒流充放电等手段对材料的物理和电化学性能进行表征。结果表明：采用不同前处理工艺制备出的Li[Ni1/3Mn1/3Co1/3]O2材料在结构、形貌和电化学性能上有较大差异;与球磨处理法制备的材料相比,采用液相法前处理工艺制备的Li[Ni1/3Mn1/3Co1/3]O2不但保持了前驱体较好的球形形貌,同时还具有较好的循环稳定性和倍率性能;该样品在20mA/g电流密度下,首次放电容量为178mA·h/g,50次循环后,容量保持率达98.7%;在1000mA/g电流密度下,样品容量为135mA·h/g。     

锂离子电池正极材料LiNi_1/3Co_1/3Mn_1/3O_2的研究进展

介绍了一种新型的锂离子电池正极材料LiNi1/3Co1／3Mn1／3O2的最新研究状况,描述了材料的晶体及电子结构,以及电化学性能;重点总结了现今国内外制备此材料的几种主要合成方法及研究进展;同时,介绍了不同掺杂元素（Fe、B、Al、Ti）对材料的改性作用。     

Zn对锂电池材料LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2结构和电化学性能的影响

采用共沉淀法掺入少量Zn得到Li(Ni1/3Co1/3Mn1/3)1-xZnxO2材料。通过X射线衍射、光电子能谱(XPS)和电化学测试研究掺杂对其晶体结构、元素价态和电化学行为的影响。结果表明:掺入Zn增大晶格常数;在粉末颗粒表面的Zn含量是颗粒内部的数十倍;掺杂后Co、Mn依然保持+3、+4价,但是Ni由+2、+3混合价态组成;掺入少量Zn阻止电极在4.5V电位下的不可逆氧化反应;掺入Zn有效改善高截止电压下的循环容量保持能力,其作用与改变材料表面状态有关。     

Surface Modification of Li1.6(Fe0.2Ni0.2Mn0.6)O2.6 by V2O5- Coating

在采用低温共沉淀-水热-煅烧法合成锂离子电池Fe-Ni-Mn体系正极材料Li1.6(Fe0.2Ni0.2Mn0.6)O2.6的基础上,对合成的材料Li1.6(Fe0.2Ni0.2Mn0.6)O2.6进行V2O5的包覆改性研究,以提高材料Li1.6(Fe0.2Ni0.2Mn0.6)O2.6的首次放电比容量和循环性能。用XRD、SEM、TEM、ICP光谱和恒流充放电测试研究包覆材料的结构和电化学性能。结果表明,V2O5包覆并没有改变材料的晶体结构,只存在于材料的表面,与未包覆的材料相比,V2O5包覆后的材料具有更好的首次放电容量和容量保持率。50周循环后,添加质量分数3%V2O5样品Li1.6(Fe0.2Ni0.2Mn0.6)O2.6的放电比容量可以维持在200.3 mAh/g,大于未添加V2O5样品Li1.6(Fe0.2Ni0.2Mn0.6)O2.6的194.0 mAh/g。CV测试表明,包覆层的存在有效抑制了材料层状结构的转变及电极与电解液的负反应。     

Surface modification of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> with Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> for lithium ion batteries

Cr 2 O 3-coated LiNi 1/3 Co 1/3 Mn 1/3 O 2 cathode materials were synthesized by a novel method. The structure and electrochemical properties of prepared cathode materials were measured using X-ray diffraction (XRD), scanning electron microscopy (SEM), charge-discharge tests, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The measured results indicate that surface coating with 1.0 wt% Cr 2 O 3 does not affect the LiNi 1/3 Co 1/3 Mn 1/3 O 2 crystal structure (α-NaFeO 2 ) of the cathode material compared to the pristine material, the surfaces of LiNi 1/3 Co 1/3 Mn 1/3 O 2 samples are covered with Cr 2 O 3 well, and the LiNi 1/3 Co 1/3 Mn 1/3 O 2 material coated with Cr 2 O 3 has better electrochemical performance under a high cutoff voltage of 4.5 V. Moreover, at room temperature, the initial discharging capacity of LiNi 1/3 Co 1/3 Mn 1/3 O 2 material coated with 1.0 wt.% Cr 2 O 3 at 0.5C reaches 169 mAh·g 1 and the capacity retention is 83.1% after 30 cycles, while that of the bare LiNi 1/3 Co 1/3 Mn 1/3 O 2 is only 160.8 mAh·g 1 and 72.5%. Finally, the coated samples are found to display the improved electrochemical performance, which is mainly attributed to the suppression of the charge-transfer resistance at the interface between the cathode and the electrolyte.     

LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维的合成与电化学性能

以溶胶前驱体为纺丝液,通过静电纺丝法合成锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维.采用原子力显微镜(AFM)、X射线衍射(XRD)、充放电实验对纳米纤维的形貌、结构和电化学性能进行研究.结果表明,纳米纤维的直径在150～200 nm之间,且具有典型的α-NaFeO2层状结构.LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维的首次放电容量均超过170 mAh·g-1,50次循环后容量保持率在90%以上.     

正极材料LiNi0.4Co0.2Mn0.4O2阴离子掺杂改性研究

采用溶胶-凝胶法合成了层状LiNi0.4Co0.2Mn0.4O1.97X0.03(X=O,F,Cl)正极材料。以XRD、SEM、CV、EIS和充放电测试等手段对材料的晶体结构、表观形貌和电化学性能进行表征。XRD结果显示F-和Cl-掺杂没有改变晶体的六方单层状结构;CV结果表明掺杂提高了材料的可逆性;充放电测试表明,F-和Cl-掺杂均提高了材料的放电容量,并改善了材料的循环性能;EIS测试结果发现,F-和Cl-掺杂均有效地抑制其在循环过程中电化学反应阻抗的增加。     

LiNi_(0.5)Mn_(0.5)O_2电极在LiNO_3电解液中的电化学性能及循环衰减机理(英文)

研究LiNi0.5Mn0.5O2电极在LiNO3水溶液中的电化学行为,同时分析该电极在不同pH值电解液中的循环衰减原因。循环伏安测试显示LiNi0.5Mn0.5O2在浓度为5 mol/L的LiNO3水溶液中具有较好的锂离子脱嵌能力。对比发现,LiNi0.5Mn0.5O2电极在浓度为5 mol/L,pH值为12的LiNO3水溶液中具有最好的循环稳定性能。通过交流阻抗法、X射线衍射分析及电极形貌的对比分析发现:电极在浓度为5 mol/L,pH值为12的LiNO3水溶液中循环时,电极的表面形貌和电极结构都能得到较好的保持,电极的电荷传递阻抗得到明显抑制,因此在该pH值电解液中的循环稳定性最好。     

Effects of sodium substitution on properties of LiMn2O4 cathode for lithium ion batteries

Na-doped Li1.05Mn2O4 cathodes were synthesized using a sol-gel process.The samples were characterized by X-ray diffractometry(XRD),cyclic voltammetry(CV),electrochemical impedance spectroscopy(EIS)and charge-discharge measurements. The results show that all the samples exhibit the same cubic spinel phase structure without impurity.The lattice constant and unit cell volume decrease with increasing the sodium dopant amount.As the molar ratio of sodium to manganese(x=n(Na)/n(Mn))increases from 0 to 0.03,the initial discharge capacity of the Li1.05Mn2O4 cathodes decreases from 119.2 to 107.9 mA·h/g,and the discharge capability at large current rate and the storage performance decline dramatically,while cycling performance at room temperature and 55℃are improved.The CV and EIS studies indicate that reversibility of Li1.05Mn2O4 cathodes decreases and the electrochemical impedance increases with increasing the sodium dopant amount.     

Li1+x(Fey/2Niy/2Mn1-y)1-xO2正极材料的合成及电化学性能

采用低温共沉淀-水热-煅烧法合成了锂离子电池Fe-Ni-Mn体系正极材料Li1+x(Fey/2Niy/2Mn1-y)1-xO2,并用XRD、SEM、ICP光谱和电化学性能测试对材料进行了表征.XRD测试和ICP分析表明,Fe、Ni取代Li2MnO3中的部分Mn,形成很好的固溶结构yLiFe1/2Ni1/2O2-(1-y)Li2MnO3 (y=0.l,0.2,0.3,0.4,0.5).SEM测试表明,取代量y不同,材料的表观形貌有所不同,y=0.4时材料的颗粒粒径均匀、较小,呈类球形结构.电化学性能测试表明,当y=0.4时,循环稳定性最好,充放电50次后放电比容量仍可维持在195.0 mAh/g,放电中值电压为3.5 V,y=0.4时样品在大倍率放电下的电化学性能表现良好.     

Synthesis and electrochemical performance of 5V spinel LiNi0.5Mn1.5O4 prepared by solid-state reaction

Spinel compound LiNi0.5Mn1.5O4 with high capacity and high rate capability was synthesized by solid-state reaction. At first, MnCl2·4H2O and NiCl2·6H2O were reacted with (NH4)2C2O4·H2O to produce a precursor via a low-temperature solid-state route, then the precursor was reacted with Li2CO3 to synthesize LiNi0.5Mn1.5O4. The effects of calcination temperature and time on the physical properties and electrochemical performance of the products were investigated. Samples were characterized by thermal gravimetric analysis(TGA), scanning electron microscopy(SEM), X-ray diffractometry(XRD), charge-discharge tests and cyclic voltammetry measurements. Scanning electron microscopy(SEM) image shows that as calcination temperature and time increase, the crystallinity of the samples is improved, and their grain sizes are obviously increased. It is found that LiNi0.5Mn1.5O4 calcined at 800 ℃ for 6 h exhibits a typical cubic spinel structure with a space group of Fd3m. Electrochemical tests demonstrate that the sample obtained possesses high capacity and excellent rate capability. When being discharged at a rate as high as 5C after 30 cycles, the as-prepared LiNi0.5Mn1.5O4 powders can still deliver a capacity of 101 mA-h/g, which shows to be a potential cathode material for high power batteries.     

共沉淀法制备LiNi0.8Co0.1Mn0.1O2过程中加料速度对其性能的影响

采用共沉淀法制备Ni0.8Co0.1Mn0.1(OH)2前驱体,与LiOH.H2O混合后在氧气气氛中焙烧得到LiNi0.8Co0.1Mn0.1O2正极材料,探讨共沉淀反应过程中快速加料和慢速加料制度对前驱体形貌和LiNi0.8Co0.1Mn0.1O2正极材料性能的影响。通过X射线衍射(XRD)、扫描电镜(SEM)和电化学测试对样品进行表征。结果表明:慢速加料法减小了材料的粒径,合成了平均粒径在0.5μm左右的球形Ni0.8Co0.1Mn0.1(OH)2前驱体,且粒径分布比较集中;所合成LiNi0.8Co0.1-Mn0.1O2正极材料具有良好的层状结构,且无杂相存在;缓慢加料法得到的样品的电化学性能有很大提高,在0.1 C、0.5 C和1 C下首次放电比容量分别达到223.5、194.3和190.7 mA.h/g,循环30次后,容量保持率为80.09%、80.80%和85.84%。     

Synthesis and characterization of LiNi0.45Co0.10Mn0.45O2 cathode for lithium ion batteries

1INTRODUCTIONAdvanced rechargeable lithium ion batteriesare attractive for use in consumer electronic andelectric vehicle(EV)application because of a fa-vorable combination of voltage,energy density,cycling performance,and have been developed rap-idly worldwide during the past decade[1,2].LiCoO2has been widely used as a cathode material in com-mercial lithiumion battery because it is reasonableeasy to synthesize and shows a stable discharge ca-pacity[3].But due to its high cost and toxic…