首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 281 毫秒
1.
研究了γ相分布和淬火处理对WC-Co合金矫顽磁力Hc的影响规律和机理。结果表明:WC-Co合金Hc与γ相分布有着密切关系,其随合金中Co%和dWC增加而降低的程度在低Co合金范围内符合线性规律,在高Co合金中则平缓降低,这是由于WC邻接度CWC-WC对γ相磁畴在反磁化过程中的阻滞作用的影响;淬火处理提高WC-Co合金的Hc主要是由于对淬火对γ相成分和应力状态的影响。  相似文献   

2.
WC-Co硬质合金的矫顽磁力   总被引:8,自引:0,他引:8  
研究了γ相分布和淬火处理对WC-C0合金矫顽磁力Hc的影响规律和机理。结果表明:WC-C0合金Hc与γ相分布有着密切关系,其随合金中Co%和dwc增加而降低的程度在低Co合金范围内符合线性规律,在高Co合金中则平缓降低,这是由于WC邻接度Cwc-wc对γ相磁畴在反磁化过程中的阻滞作用的影响;淬火处理提高WC-Co合金的Hc主要是由于淬火对γ相成分和应力状态的影响。  相似文献   

3.
刘寿荣  刘方 《焊接学报》1994,15(3):185-190
研究了高频钎焊同时淬火处理对WC-20Co硬质合金刀片显微结构和性能的影响。结果表明,在1000-1200℃温度范围内处理将导致WC-20Co合金刀片中WC相邻接度∑WC-WC下降,γ相平均自由程Lγ增加,韧性改善和硬度提高等一系列淬火效果。断口殂貌微观特征也表明了合金韧性的提高。当处理温度超过1200℃后,WC-20Co合金的显微结构和性能将恶化。  相似文献   

4.
WC-20Co硬质合金钎焊的热处理机理   总被引:3,自引:0,他引:3  
研究了高频钎焊同时淬火处理对WC-20Co硬质合金刀片显微结构和性能的影响。结果表明,在1000~1200℃温度范围内处理将导致WC-20Co合金刀片中WC相邻接度∑WC-WC下降、r相平均自由程L_r增加、韧性改善和硬度提高等一系列淬火效果。断口形貌微观特征也表明了合金韧性的提高。当处理温度超过1200℃后,WC-20Co合金的显微结构和性能将恶化。  相似文献   

5.
本文叙述了WC-Co硬质合金特别是YG25牌号硬质合金的渗硼淬火热处理强化工艺和不同钴含量的合金的强化处理效果以及强化处理的合金应用效果,并对其强化机理进行了讨论。  相似文献   

6.
研究了热处理工艺对粉末冶金Ni-Cr-W-Co-Fe-C合金组织结构的影响。结果表明,烧结合金经950℃热处理可以获得最佳的组织和性能。热处理后粉末冶金合金的性能可超过真空熔炼的同类合金。  相似文献   

7.
WC—Co硬质合金热处理后的TEM观察   总被引:3,自引:1,他引:2  
对YG11C和YG13C两种牌号硬质合金热处理后的微观组织进行了TEM分析,通过电子衍射花样的标定,确认了CoxWyCz物相在淬火回火所得的面心立方钴(α-Co)中的存在,并结合硬质合金热处理前后抗弯强度的测定,其该类物相在面心立方钴中的作用进行了初步探讨,结果表明:ε-M,Co3W,Co7W6,k-Co3W9C4等物相在热处理后的硬质合金中可起的强化作用,从而提高硬质合金的抗弯强度。  相似文献   

8.
Fe-W-Co和Fe-W-Co-Ni合金的时效硬化   总被引:1,自引:0,他引:1  
对FeWCo和FeWCoNi合金的时效硬化特性进行了研究。结果表明两种合金均具有强的时效硬化能力。FeWCoNi低温硬化速率较FeWCo高。随着时效温度升高,FeWCo硬化速率迅速上升。FeWCo合金630℃时效10min,硬度从淬火态的47HRC上升到64HRC。淬火组织为具有高位错密度的板条马氏体。时效初期出现调幅结构,产生较大共格应力。570℃×2h时效,FeWCo的析出物比FeWCoNi更为弥散细小。这是FeWCo合金较FeWCoNi合金有较强时效硬化能力的原因。  相似文献   

9.
共沉淀回收硬质合金的组织结构和性能   总被引:2,自引:0,他引:2  
以共沉淀回收废硬质合金的W-Co复合物为原料制备的再生WC-10Co硬质合金具有WC平均晶粒细、矫顽磁力和硬度高的优点,但较多的WC晶粒缺陷、较高的WC晶粒邻接度Cwc-wc和不连续长大的粗晶WC的存在降低了其强韧性。用共沉淀回收料制备两相WC-Co合金,须实施较生产普通WC-Co合金更为严格的碳含量控制。  相似文献   

10.
张勇 《铸锻热》1998,(2):9-12
在等离子体中渗入一定厚度W-Mo合金,再离子碳氮共渗,真空加压气淬火淬,回火制成的20Cr奂锯条,与整体高碳钢,高速钢锯条相比,具有生产工艺生产,成本低的优点。这是一种先进热处理技术,将具有广泛的应用前景。  相似文献   

11.
WC–Co cemented carbides, well-known as the conventional tooling materials, have not been successfully produced by one step additive manufacturing processes such as selective laser melting(SLM) yet. The microstructure evolution as well as WC grain growth behavior has rarely been investigated in detail during SLM process. In this study, the WC–Co cemented carbides with different Co contents(12–32 wt%) were prepared by optimized SLM processes for comparative investigation of densification behavior, microstructure characterization and mechanical property. The increase in Co content in feedstock carbide granules can improve the densification behavior during SLM process. The SLM processed WC-12 Co shows larger average WC grain size and higher percentage of coarser WC grains as compared with both WC-20 Co and WC-32 Co. The microstructure characterization, combined with finite element simulation, shows the WC grain growth mechanisms include agglomeration and dissolution-deposition of WC during SLM process and agglomeration of WC is an important mechanism especially for WC–Co cemented carbides with Co content as low as 12 wt%. The comparison between horizontal(perpendicular to the SLM laser beam) and vertical(parallel to the SLM laser beam) cross sections of carbides shows that SLM process introduces a certain degree of microstructure and mechanical behavior anisotropy for WC-12 Co, WC-20 Co, and WC-32 Co.  相似文献   

12.
过渡族金属碳化物是最常见的硬质合金微观组织结构与性能调控添加剂,添加剂在硬质合金中赋存状态的研究是WC晶粒生长抑制机理研究的基础,也是硬质合金材料与工艺设计的基础。从基于第一性原理计算的理论研究、基于高分辨透射电镜和原子探针层析法的实验观察分析等2个方面,综述了过渡族金属碳化物在WC/β(钴基固溶体粘结相)相界偏析行为的研究现状。基于过渡族金属碳化物在硬质合金中晶界与相界的偏析行为、在硬质相与粘结相中的固溶行为,讨论了硬质合金中WC晶粒生长机理与晶粒生长抑制机理以及过渡族金属碳化物对硬质合金性能的影响机理,提出了硬质合金材料与工艺设计的建议。  相似文献   

13.
含板状WC晶粒硬质合金的强韧化机制研究   总被引:1,自引:0,他引:1  
通过加入2.5%板状WC晶种,制备含板状WC晶粒硬质合金,研究其强韧化机制。结果表明:WC晶粒的各向异性和形状改变诱导的Hall-Petch硬化是硬质合金硬度增加的主要原因。加入板状晶种后,裂纹在扩展过程中出现了明显的穿晶断裂和Co相桥接,增加了裂纹偏转,硬质合金的抗弯强度大大提高。不同Co含量和初始WC粉体粒度制备的含板状WC晶粒硬质合金,穿晶断裂、Co相桥接和裂纹偏转对抗弯强度增加的贡献不同。  相似文献   

14.
Cemented carbides of the WC-Co-Re system represent a new class of hard materials having a significantly increased Young's modulus, hot hardness and high temperature creep resistance. The WC-Co-Re phase diagram was evaluated and compared with the corresponding WC-Co phase diagram. Physical and mechanical properties of such composites were measured at room and elevated temperatures and compared with those of conventional WC-Co cemented carbides. Microstructures of the WC-Co-Re cemented carbides at different carbon contents, binder contents and WC grain sizes were examined. Rhenium being dissolved in the Co-based binder is found to be a very strong grain growth inhibitor with respect to WC coarsening during liquid-phase sintering. The Young's modulus, hot hardness and high temperature creep resistance of the WC-Co-Re cemented carbides are greater than those of conventional WC-Co cemented carbides. Due to their unique properties the WC-Co-Re materials can find applications in use in high-pressure high-temperature components for synthesis of diamond and c-BN and cutting Ni-based super alloys and other heat-generating workpiece materials.  相似文献   

15.
焦鹏鹤  余浩  陈异  蒋显全 《硬质合金》2011,28(4):212-218
采用真空烧结方式制备超细晶WC-10%Co硬质合金,研究了复合添加晶粒长大抑制剂Cr3C2/NbC对合金组织及性能的影响。结果表明:在1400℃烧结条件下,添加剂的组成为0.4%Cr3C2+0.3%NbC时(文中含量均为质量分数),合金具有最好的综合力学性能,抗弯强度可达1951MPa、硬度1615HV30;WC平均晶粒尺寸为490nm。经SEM观察并通过EDS发现,抑制剂Cr3C2/NbC固溶到粘结相Co中,改变界面能,限制WC晶粒的长大;同时,也会降低WC在粘结相Co中的溶解度,从而起到细化晶粒的作用。  相似文献   

16.
WC grain size has significant effect on WC-Co cemented carbide alloy properties. In order to inhibit WC grain growth during sintering process, grain growth-inhibitor Cr3C2 is usually added to tungsten carbide powder in advance through mechanical milling. While, homogeneous distribution of Cr3C2 in the tungsten carbide powder is difficult to achieve and result in abnormal growth of WC grains. For this purpose of growth-inhibitor uniform distribution, (CH3COO)3Cr is added into ammonium tungstate solution during evaporation and crystallization process to prepare Cr-doped APT powder, which can be used as precursor for ultrafine-grained WC-Co cemented carbide alloy preparation. Compared with conventional APT powder, the Cr-doped APT has smaller particle size and bulk density, moreover, chromium is evenly distributed within it. The Cr-doped APT is then used to produce Cr-doped tungsten powder, which also has smaller particle size than that of conventional tungsten powder. Cr-doped tungsten powder is subsequently prepared into tungsten carbide powder and WC-Co cemented carbide alloy through carbonization and sintering process, respectively. Compared with conventional WC-Co cemented carbide alloy, the obtained WC-Co cemented carbide alloy has smaller mean WC grain size (0.36 μm), and more uniform microstructure. Furthermore, the phenomenon of WC grain abnormal growth during sintering process is not observed, because the grain growth-inhibitor Cr3C2 is well dispersed in tungsten carbide and cobalt composite powder. Results show that the obtained WC-Co cemented carbide alloy presents better mechanical properties (HRA, bending strength, coercive force) than those of conventional WC-Co cemented carbide alloy. Accordingly, the novel addition of (CH3COO)3Cr during the evaporation and crystallization process is the key factor of ultrafine-grained WC-Co cemented carbide alloy production.  相似文献   

17.
WC-Co硬质合金的弹性性能   总被引:4,自引:3,他引:1  
李安海  赵军  王泽明  郑伟 《硬质合金》2011,28(3):194-198
综述了WC-Co硬质合金弹性性能的预测模型,并计算了硬质合金不同Co含量时的弹性性能参数值,并对不同的模型的预测值与文献中的测量结果进行了比较。采用引入WC晶粒邻接度C的Golovchan模型计算的WC-Co硬质合金的弹性模量值,相比Voigt-Reuss模型和Hashin-Shtrikman模型,更接近于实测值。而泊松比的值相对偏低,但可以采用Hashin-Shtrikman模型的泊松比上限确定泊松比的值。另外,给出了弹性模量的实验测定方法标准。这为硬质合金重要弹性参数值的确定提供了实验测定和理论计算的依据。  相似文献   

18.
WC-Co硬质合金的强度   总被引:16,自引:8,他引:8  
刘寿荣 《硬质合金》2002,19(3):129-135
对两相 WC- Co硬质合金的研究表明 ,并非由钴含量 XCo而是由碳含量 XC 所决定的 相成分 (钨和碳在 相中的浓度 )才是制约 WC在 相中溶解—析出过程的决定性因素 ,因而也是影响 WC- Co合金 WC平均晶粒尺寸 LWC的重要因素。求得了相应于最大抗弯强度 σTRSmax的 LWC~ XCo反比关系式和最佳 相平均自由程 λ。 的取值范围。提出了在 相质量分数 X 增大引起 λ。 增大的情况下 λ 对应的合金结构由连续的 WC骨架向连续的 相网络的过渡的概念 ,从而较合理地解释了σTRSmax~λ 双支线关系和粗、细晶合金的σTRS~ XC关系。两相 WC- Co合金的强度取决于合金的钴含量、碳含量和WC平均晶粒尺寸并归因于 相平均自由程和 相中钨和碳固溶度的影响。在σTRS~λ 左支线范围内合金的断裂韧性 KIC同σTRS呈线性关系。在求得显微结构参数、成分和强度同磁性、密度和硬度的定量关系的基础上提出了无损鉴定两相 WC- Co硬质合金的结构、成分和强度的原理。  相似文献   

19.
硬质合金的比矫顽磁力   总被引:8,自引:2,他引:6  
用磁性法和 X射线衍射相分析得出了当两相 WC— Co硬质合金碳含量改变时 ,其比矫顽磁力 Hsc( A· m2 · Kg- 1)同合金碳含量 Xc、真实钴含量 XCo( wt)、WC相平均晶粒尺寸 Lwc( μm)及比饱和磁化强度 4πσ( A·m2 · kg- 1)、密度 d( Kg· m- 3)间的定量关系式Hsc+ 0 .330 4 lg L wc=7.652 - 0 .330 4 lg 1 .791 XCo1 - 1 .0 87XCo- 7.356XCo- 1 2 0 .0 Xc=0 .2 958- 0 .330 4 lg 1 .791 XCo1 - 1 .0 87XCo+ 6.488XCo- 3.2 64× 1 0 - 34 πσ=1 1 .86- 0 .330 4 lg 1 .791 XCo1 - 1 .0 87XCo+ 8.1 35XCo- 1 .0 83× 1 0 5· d- 1当合金碳含量变化时 ,溶质钨和碳在 γ相中固溶度的变化引起 γ相磁矩和 γ基体钴晶格畸变应力的改变是导致合金 Hsc值变化的主要原因。  相似文献   

20.
陈慧  栾道成  李力  李亚军 《硬质合金》2012,29(2):101-105
采用高能球磨法制备超细WC-Co硬质合金。研究了1 390℃真空通Ar常规烧结后再热等静压烧结(HIP),烧结温度1 320℃,80 MPa下保温60 min对WC-Co硬质合金组织和性能的影响。结果表明:1 390℃真空通Ar烧结,可获得组织细小、综合性能好的YG8、YG10超细硬质合金。其中YG8超细硬质合金硬度达93.8 HRA,抗弯强度达2 290 MPa,YG10超细硬质合金硬度达93.3 HRA,抗弯强度达2 250 MPa。真空通Ar常规烧结再HIP能提高合金的致密度,但会使WC晶粒长大,硬度、抗弯强度、矫顽磁力等性能均下降。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号