Effect of Critical Plasma Spray Parameters on Microstructure and Microwave Absorption Property of Ti<Subscript>3</Subscript>SiC<Subscript>2</Subscript>/Cordierite Coatings

Ti₃SiC₂/cordierite coatings with different critical plasma spray parameters (CPSP) were fabricated via atmospheric plasma spraying method. The microstructure and phase constitution of the as-sprayed Ti₃SiC₂/cordierite coatings were characterized. The effects of CPSP conditions on the electromagnetic shielding, and dielectric and microwave absorption properties of coatings in the frequency of 8.2-12.4 GHz were also measured and investigated. The results showed that both real and imaginary part of the complex permittivity decrease with increasing CPSP values, which can be ascribed to the decomposition of some Ti₃SiC₂ into TiC. The calculated reflection loss of the as-sprayed Ti₃SiC₂/cordierite coatings with different CPSP conditions and thicknesses indicates that coatings with CPSP 0.3, 0.35, and 0.425 exhibit excellent microwave absorption property in the thickness of 1.5 mm. In order to broaden the bandwidth of the coatings, a double-layer coating system was designed. The calculated reflection loss results show that when the thickness of matching layer is 0.3 mm and the thickness of absorbing layer is 1.5 mm, the double-layer coating system shows a proper microwave absorption property with a minimum absorption value of ?17.37 dB at 9.67 GHz and a absorption bandwidth (RL less than ?5 dB) of 4.16 GHz in the investigated frequency.     

Comparison of ZrB<Subscript>2</Subscript>-MoSi<Subscript>2</Subscript> Composite Coatings Fabricated by Atmospheric and Vacuum Plasma Spray Processes

In this work, ZrB₂-20 vol.% MoSi₂ (denoted as ZM) composite coatings were fabricated by atmospheric plasma spray (APS) and vacuum plasma spray (VPS) techniques, respectively. Phase composition and microstructure of the composite coatings were characterized. Their oxidation behaviors and microstructure changes at 1500 °C were comparatively investigated. The results showed that VPS-ZM coating was composed of hexagonal ZrB₂, tetragonal and hexagonal MoSi₂, while certain amount of ZrO₂ existed in APS-ZM coating. The oxide content, surface roughness and porosity of VPS-ZM coating were apparently lower than those of APS-ZM coating. The mass gain of APS-ZM coating was maximum at the beginning (1500 °C, 0 h) and then decreased with the oxidation time extending, while the mass of VPS-ZM coating gradually increased with increasing the oxidation time. The possible reasons for the different oxidation behaviors of the two kinds of coatings were analyzed.     

Thermal Spray Deposition,Phase Stability and Mechanical Properties of La<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>/LaAlO<Subscript>3</Subscript> Coatings

This paper deals with the deposition of La₂Zr₂O₇ (LZO) and LaAlO₃ (LAO) mixtures by air plasma spray (APS). The raw material for thermal spray, single phase LZO and LAO in a 70:30 mol.% ratio mixture was prepared from commercial metallic oxides by high-energy ball milling (HEBM) and high-temperature solid-state reaction. The HEBM synthesis route, followed by a spray-drying process, successfully produced spherical agglomerates with adequate size distribution and powder-flow properties for feeding an APS system. The as-sprayed coating consisted mainly of a crystalline LZO matrix and partially crystalline LAO, which resulted from the high cooling rate experienced by the molten particles as they impact the substrate. The coatings were annealed at 1100 °C to promote recrystallization of the LAO phase. The reduced elastic modulus and hardness, measured by nanoindentation, increased from 124.1 to 174.7 GPa and from 11.3 to 14.4 GPa, respectively, after the annealing treatment. These values are higher than those reported for YSZ coatings; however, the fracture toughness (K _IC) of the annealed coating was only 1.04 MPa m^0.5.     

Effect of Nano-Si<Subscript>3</Subscript>N<Subscript>4</Subscript> Additives and Plasma Treatment on the Dry Sliding Wear Behavior of Plasma Sprayed Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-8YSZ Ceramic Coatings

In this paper, the effect of nano-Si₃N₄ additives and plasma treatment on the wear behavior of Al₂O₃-8YSZ ceramic coatings was studied. Nano-Al₂O₃, nano-8YSZ (8 wt.% Y₂O₃-stabilized ZrO₂) and nano-Si₃N₄ powders were used as raw materials to fabricate four types of sprayable feedstocks. Plasma treatment was used to improve the properties of the feedstocks. The surface morphologies of the ceramic coatings were observed. The mechanical properties of the ceramic coatings were measured. The dry sliding wear behavior of the Al₂O₃-8YSZ coatings with and without Si₃N₄ additives was studied. Nano-Si₃N₄ additives and plasma treatment can improve the morphologies of the coatings by prohibiting the initiation of micro-cracks and reducing the unmelted particles. The hardness and bonding strength of AZSP (Al₂O₃-18 wt.% 8YSZ-10 wt.% Si₃N₄-plasma treatment) coating increased by 79.2 and 44% compared to those of AZ (Al₂O₃-20 wt.% 8YSZ) coating. The porosity of AZSP coating decreased by 85.4% compared to that of AZ coating. The wear test results showed that the addition of nano-Si₃N₄ and plasma treatment could improve the wear resistance of Al₂O₃-8YSZ coatings.     

Elevated Temperature Solid Particle Erosion Performance of Plasma-Sprayed Co-based Composite Coatings with Additions of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and CeO<Subscript>2</Subscript>

In this paper, investigation into solid particle erosion behavior of atmospheric plasma-sprayed composite coating of CoCrAlY reinforced with Al₂O₃ and CeO₂ oxides on Superni 76 at elevated temperature of 600 °C is presented. Alumina particles are used as erodent at two impact angles of 30° and 90°. The microstructure, porosity, hardness, toughness and adhesion properties of the as-sprayed coatings are studied. The effects of temperature and phase transformation in the coatings during erosion process are analyzed using XRD and EDS techniques. Optical profilometer is used for accurate elucidation of erosion volume loss. CoCrAlY/CeO₂ coating showed better erosion resistance with a volume loss of about 50% of what was observed in case of CoCrAlY/Al₂O₃/YSZ coating. Lower erosion loss is observed at 90° as compared to 30° impact angle. The erosion mechanism evaluated using SEM micrograph revealed that the coatings experienced ductile fracture exhibiting severe deformation with unusual oxide cracks. Reinforced metal oxides provide shielding effect for erodent impact, enabling better erosion resistance. The oxidation of the coating due to high-temperature exposure reforms erosion process into oxidation-modified erosion process.     

Tribocorrosion Behavior of Fe-Based Amorphous Composite Coating Reinforced by Al<Subscript>2</Subscript>O<Subscript>3</Subscript> in 3.5% NaCl Solution

Although corrosion and friction/wear behavior of Fe-based amorphous coatings and their composites has been extensively studied during the past decade, there is very limited work related to tribocorrosion behavior. In this paper, the tribocorrosion behavior of a Fe-based amorphous composite coating reinforced with 20 wt.% Al₂O₃ particles was investigated in a 3.5% NaCl solution on a ball-on-disk tester and was compared to the monolithic amorphous coating and 316L stainless steel (SS). The results showed that the amorphous composite coating exhibited the highest tribocorrosion resistance among the three materials tested, as evidenced by the lowest coefficient of friction (~0.3) and tribocorrosion wear rate (~1.2 × 10^?5 mm³/N·m). In addition, potentiodynamic polarization measurements before and during tribocorrosion testing demonstrated that corrosion resistance of the amorphous composite coating was not influenced so much by mechanical loading compared to the amorphous coating and the 316L SS. Observations on the worn surface revealed a corrosion-wear- and oxidational-wear-dominated tribocorrosion mechanism for the composite coatings. The excellent tribocorrosion resistance of the composite coating results from the effect of chemically stable Al₂O₃ phase which resists oxidation and delamination during sliding, along with poor wettability with corrosive NaCl droplets.     

Plasma-electrolytic oxidation of titanium in Zr(SO<Subscript>4</Subscript>)<Subscript>2</Subscript>-containing electrolyte

It is shown that anodic oxide coatings with a thickness of several to 300 νm can be obtained on titanium by varying the charge spent on (Q). The prevailing phase in the coatings is ZrO₂ in monoclinic and tetragonal modifications. The content of zirconium in the layers is up to 20 at %. Distributions of titanium, zirconium, and oxygen in the cross sections of the coatings are obtained, and the effect of Q on the formation and elementary and phase compositions of the coatings is studied. Tentative experiments clarifying the effects of bipolar anodic-cathodic polarization and electrolyte aging on the composition of coatings are carried out. The coatings are shown to be stable at temperature variations in the range of 20–700°C and to decrease the contact corrosion current at the (titanium + coating)—St3 steel interface by a digit of 10–15 in 3% NaCl.     

Preparation of SrZrO<Subscript>3</Subscript> Thermal Barrier Coating by Solution Precursor Plasma Spray

The solution precursor plasma spray (SPPS) process is capable of depositing highly durable thermal barrier coatings (TBCs). In this study, an aqueous chemical precursor feedstock was injected into the plasma jet to deposit SrZrO₃ thermal barrier coating on metal substrate. Taguchi design of experiments was employed to optimize the SPPS process. The thermal characteristics and phase evolution of the SrZrO₃ precursor, as well as the influence of various spray parameters on the coating deposition rate, microhardness, microstructure, and phase stability, were investigated. The experimental results showed that, at given spray distance, feedstock flow rate, and atomization pressure, the optimized spray parameters were arc current of 600 A, argon flow rate of 40 L/min, and hydrogen flow rate of 10 L/min. The SrZrO₃ coating prepared using the optimized spray parameters had single-pass thickness of 6.0 μm, porosity of ~18%, and microhardness of 6.8 ± 0.1 GPa. Phase stability studies indicated that the as-sprayed SrZrO₃ coating had good phase stability in the temperature range from room temperature to 1400 °C, gradually exhibiting a phase transition from t′-ZrO₂ to m-ZrO₂ in the SrZrO₃ coating at 1450 °C with increasing time, while the SrZrO₃ phase did not change.     

High-Temperature Erosive Behavior of Plasma Sprayed Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-NiCr/Cenosphere Coating

This research examines the deposition of Cr₃C₂-NiCr/cenosphere and Cr₃C₂-NiCr coatings on MDN 321 steel through the process of plasma spray. In this process, the solid particle erosion test is established at 200, 400, 600 °C with 30° and 90° impact angles. Alumina erodent is adopted to investigate the erosive behavior of the coating at higher temperatures. The properties of the Cr₃C₂-NiCr/cenosphere coating are established based on the microhardness, the adhesive strength, the fracture toughness, and the ductility. To quantify volume loss as a result of erosion, an optical profilometer is used. At higher temperature, decrease in the erosion volume loss of Cr₃C₂-NiCr/cenosphere and Cr₃C₂-NiCr coatings is observed. The erosion-resistive property of Cr₃C₂-NiCr/cenosphere coating is higher than that of MDN 321 steel by 76%. This property is influenced by high-temperature stability of mullite, alumina, and protective oxide layer that is formed at elevated temperatures. The morphology of eroded coating discloses a brittle mode of material removal.     

Microstructure and Thermomechanical Properties of Atmospheric Plasma-Sprayed Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> Coating

In this study, a Yb₂O₃ coating was fabricated by the atmospheric plasma spray technique. The phase composition, microstructure, and thermal stability of the coating were examined. The thermal conductivity and thermal expansion behavior were also investigated. Some of the mechanical properties (elastic modulus, hardness, fracture toughness, and flexural strength) were characterized. The results reveal that the Yb₂O₃ coating is predominantly composed of the cubic Yb₂O₃ phase, and it has a dense lamellar microstructure containing defects. No mass change and exothermic phenomena are observed in the thermogravimetry and differential thermal analysis curves. The high-temperature x-ray diffraction results indicate that no phase transformation occurs from room temperature to 1500 °C, revealing the good phase stability of the Yb₂O₃ coating. The coefficient of thermal expansion of the Yb₂O₃ coating is (7.50-8.67)?×?10^?6 K^?1 in the range of 200-1400 °C. The thermal conductivity is about 1.5 W m^?1 K^?1 at 1200 °C. The Yb₂O₃ coating has excellent mechanical properties and good damage tolerant. The unique combination of these properties implies that the Yb₂O₃ coating might be a promising candidate for T/EBCs applications.     

Effects of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nano-Particles on Corrosion Performance of Plasma Electrolytic Oxidation Coatings Formed on 6061 Aluminum Alloy

Corrosion resistance improvement of plasma electrolyte oxidation coatings on 6061 aluminum alloy in silicate electrolyte containing Al₂O₃ nano-particles was studied, with particular emphasis on the microstructure, coating growth, and corrosion behavior in 3.5 wt.% NaCl solution. The microstructure of coatings, their thickness, and phase composition were characterized using scanning electron microscopy and x-ray diffraction. All characterization data showed that the maximum coating thickness and lowest amount of porosity were obtained in a low concentration of KOH, a high concentration of Na₂SiO₃, and moderate concentration of Al₂O₃ nano-particles in the electrolyte. This combination describes the optimum plasma electrolytic oxidation electrolyte, which has the best conductivity and oxidizing state, as well as the highest incorporation of electrolyte components in the coating growth process. On the other hand, incorporation and co-deposition of Al₂O₃ nano-particles were more pronounced than SiO₃ ^2? ions in some level of molar concentration, which is due to the higher impact of electron discharge force on the adsorption of Al₂O₃ nano-particles. The electrochemical results showed that the best protective behavior was obtained in the sample having a coat with the lowest porosity and highest thickness.     

Effects of Laser Remelting and Oxidation on NiCrAlY/8Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> Thermal Barrier Coatings

In this study, three groups of thermal barrier coatings (TBCs) samples were remelted by CO₂ laser with different laser energy densities (1, 5 and 10 J/mm²) to seal the surface of yttria-stabilized zirconia (YSZ) coatings. Microscopic observations showed that the cracks size and the remelted depth in YSZ coatings increased. A ~ 50-μm-thick dense layer was formed on the surface of YSZ coating in samples with 1 J/mm² energy density. Microindentation tests showed that the Vickers hardness of YSZ coatings increases with the increase in laser energy density. After isothermal oxidation at 1200 °C for 200 h, thinner thermally growth oxides were found in laser remelted YSZ samples under energy density of 1 J/mm² (6.32 ± 0.28 μm). Cyclic oxidation results showed that the weight gain per unit area of low energy density laser remelted TBCs was smaller than that of the high energy density laser remelted and as-sprayed TBCs.     

Dual-Layer Oxidation-Protective Plasma-Sprayed SiC-ZrB<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Carbon Nanotube Coating on Graphite

Graphite is used in high-temperature gas-cooled reactors because of its outstanding irradiation performance and corrosion resistance. To restrict its high-temperature (>873 K) oxidation, atmospheric-plasma-sprayed SiC-ZrB₂-Al₂O₃-carbon nanotube (CNT) dual-layer coating was deposited on graphite substrate in this work. The effect of each layer was isolated by processing each component of the coating via spark plasma sintering followed by isothermal kinetic studies. Based on isothermal analysis and the presence of high residual thermal stress in the oxide scale, degradation appeared to be more severe in composites reinforced with CNTs. To avoid the complexity of analysis of composites, the high-temperature activation energy for oxidation was calculated for the single-phase materials only, yielding values of 11.8, 20.5, 43.5, and 4.5 kJ/mol for graphite, SiC, ZrB₂, and CNT, respectively, with increased thermal stability for ZrB₂ and SiC. These results were then used to evaluate the oxidation rate for the composites analytically. This study has broad implications for wider use of dual-layer (SiC-ZrB₂/Al₂O₃) coatings for protecting graphite crucibles even at temperatures above 1073 K.     

Microstructure and Thermophysical Properties of SrZrO<Subscript>3</Subscript> Thermal Barrier Coating Prepared by Solution Precursor Plasma Spray

Strontium zirconate (SrZrO₃) thermal barrier coatings were deposited by solution precursor plasma spray (SPPS) using an aqueous precursor solution. The phase transition of the SrZrO₃ coating and the influence of the aging time at 1400 °C on the microstructure, phase stability, thermal expansion coefficient, and thermal conductivity of the coating were investigated. The unique features of SPPS coatings, such as interpass boundary (IPB) structures, nano- and micrometer porosity, and through-thickness vertical cracks, were clearly observed evidently in the coatings. The vertical cracks of the coatings remained substantially unchanged while the IPB structures gradually diminished with prolonged heat treatment time. t-ZrO₂ developed in the coatings transformed completely to m-ZrO₂ phase after heat treatment for 100 h. Meanwhile, the SrZrO₃ phase in the coatings exhibited good phase stability upon heat treatment. Three phase transitions in the SrZrO₃ coatings were revealed by thermal expansion measurements. The thermal conductivity of the as-sprayed SrZrO₃ coating was ~1.25 W m^?1 K^?1 at 1000 °C and remained stable after heat treatment at 1400 °C for 360 h, revealing good sintering resistance.     

Microstructure and High-Temperature Oxidation Behavior of Cold Gas-sprayed Ni-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Coatings

Cermet coatings are widely used for high-temperature industrial applications. This study investigates the effect of high-temperature oxidation on cold gas dynamic-sprayed Ni-Al₂O₃ coatings. For this purpose, high-temperature oxidation tests were performed at 520 and 640 °C. The selected exposure times were 24, 48, 72, 168, and 336 h. The microstructural evolution during exposure at high temperature was analyzed by scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDX), and x-ray diffraction (XRD). The oxidation kinetics was estimated by thickness measurements. The results show that the coatings protect the substrates against oxidation. In order to study possible changes in the mechanical properties of the system, Vickers microhardness experiments on the coatings and on the 10CrMo9-10 steel substrates were conducted. It was observed that hardness decreased by exposing the specimens to high temperature.     

Cold-Sprayed Cu-MoS<Subscript>2</Subscript> and Its Fretting Wear Behavior

Cu and Cu-MoS₂ coatings were fabricated by cold spray, and the fretting wear performance of the two coatings was compared. A mixture (95 wt.% Cu + 5 wt.% MoS₂) was used as feedstock for the composite coating. Coatings were sprayed with identical gas flow conditions on the substrates pre-heated to approximately 170 °C. The morphology of coating top surface and polished cross sections was analyzed by scanning electron microscopy (SEM) and light optical microscopy (LOM). The influence of MoS₂ on Cu deposition was examined. The local MoS₂ concentration within the coating was found to affect the hardness. Fretting tests were carried out at two different normal loads, and the influence of MoS₂ on friction and wear was studied. The morphology and elemental compositions of the wear scars and wear debris were observed by SEM and energy dispersive x-ray spectroscopy (EDS), respectively.     

Microstructure and Thermal Properties of Atmospheric Plasma-Sprayed Yb<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>7</Subscript> Coating

In the present work, Yb₂Si₂O₇ powder was synthesized by solid-state reaction using Yb₂O₃ and SiO₂ powders as starting materials. Atmospheric plasma spray technique was applied to fabricate Yb₂Si₂O₇ coating. The phase composition and microstructure of the coating were characterized. The density, open porosity and Vickers hardness of the coating were investigated. Its thermal stability was evaluated by thermogravimetry and differential thermal analysis (TG-DTA). The thermal diffusivity and thermal conductivity of the coating were measured. The results showed that the as-sprayed coating was mainly composed of crystalline Yb₂Si₂O₇ with amorphous phase. The coating had a dense structure containing defects, such as pores, interfaces and microcracks. The TG-DTA results showed that there was almost no mass change from room temperature to 1200 °C, while a sharp exothermic peak appeared at around 1038 °C in DTA curve, which indicated that the amorphous phase crystallized. The thermal conductivity of the coating decreased with rise in temperature up to 600 °C and then followed by an increase at higher temperatures. The minimum value of the thermal conductivity of the Yb₂Si₂O₇ coating was about 0.68 W/(m K).     

Obtaining ZrO<Subscript>2</Subscript> + CeO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> + TiO<Subscript>2</Subscript>/Ti compositions by plasma-electrolytic oxidation of titanium and investigating their properties

Regularities of the effect produced by Ce₂(SO₄)₃ salt introduced in an aqueous electrolyte containing Zr(SO₄)₂ on the plasma-electrolytic formation of oxide coatings on titanium, their composition, and structure are studied. ZrO₂ + CeO _x + TiO₂ three-phase oxide coatings with a thickness about 10 μm are obtained. The coatings involve ZrO₂ cubic phase. The ZrO₂-to-TiO₂ phase ratio in the coatings can be controlled. The zirconium content in the coatings reaches 20 at %, while that of cerium is 3–5 at %. The surface layer (∼3-nm thick) contains Ce³⁺ (∼30%) and Ce⁴⁺ (∼70%). Pores in the surface part of coatings have diameters around or smaller than 1 μm and are regularly arranged. The obtained systems have a certain catalytic activity with respect to the oxidation of CO to CO₂ at temperatures above 400–450°C. The coatings are corrosion-resistant in chloride-containing environments. The thickness h of coatings depending on the charge Q supplied to the cell is described by the equation h = h ₀(Q/Q ₀) ⁿ , where n = 0.35 and h ₀ is the thickness of the coating formed at Q ₀ = 1 C/cm².     

Effect of 2D WS<Subscript>2</Subscript> Addition on Cold-Sprayed Aluminum Coating

Tungsten disulfide (WS₂) has excellent solid lubrication properties due to its 2D layered structure. This study focuses on depositing Al-2 wt.% WS₂ composite coating by cold spray technique. The effect of WS₂ addition on the microstructure, mechanical and tribological properties of the composite coatings is examined in the as-deposited and heat-treated conditions. After heat treatment, the coating density increased to 99% with improved intersplat bonding. The microhardness of the heat-treated Al-2 wt.% WS₂ coating increased by 56% as compared to the as-sprayed coating. The wear resistance of heat-treated Al-2 wt.% WS₂ coating improved by 75% with a synergistic reduction in the coefficient of friction (COF) by 51%. Transmission electron microscopy investigation reveals the presence of layered WS₂ within aluminum splats with a strong interface. This study shows that cold spraying can be effectively used to integrate 2D layered WS₂ as a solid lubricant in the metallic coatings.     

High-Temperature Oxidation of Nickel-Based Cermet Coatings Containing WC and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanosized Particles

This paper investigates the high-temperature oxidation of cermet coatings composed of two types of nanosized particles (WC and a mixture of WC and Al₂O₃) incorporated in nickel and produced by co-electrodeposition. For this purpose, high-temperature oxidation tests were conducted at three temperatures (500, 600, and 700 °C) in dry air with 6 time intervals up to 96 h and mass changes at each specific time interval was measured. Statistical techniques were used to calculate the oxidation rate constants (k) and growth-rate time constants (a) for all coatings. The confidence intervals associated with tests were also calculated. The results showed linear to sub-parabolic oxidation rates for coatings composed of only WC particles and sub-liner to liner oxidation rates for coating with both WC and Al₂O₃ particles. The reduction in oxidation rates for coatings with both WC and Al₂O₃ particles were correlated to the addition of Al₂O₃ particles in the matrix.