Suspension Plasma Spraying: Process Characteristics and Applications

Suspension plasma spraying (SPS) offers the manufacture of unique microstructures which are not possible with conventional powdery feedstock. Due to the considerably smaller size of the droplets and also the further fragmentation of these in the plasma jet, the attainable microstructural features like splat and pore sizes can be downsized to the nanometer range. Our present understanding of the deposition process including injection, suspension plasma plume interaction, and deposition will be outlined. The drawn conclusions are based on analysis of the coating microstructures in combination with particle temperature and velocity measurements as well as enthalpy probe investigations. The last measurements with the water cooled stagnation probe gives valuable information on the interaction of the carrier fluid with the plasma plume. Meanwhile, different areas of application of SPS coatings are known. In this paper, the focus will be on coatings for energy systems. Thermal barrier coatings (TBCs) for modern gas turbines are one important application field. SPS coatings offer the manufacture of strain-tolerant, segmented TBCs with low thermal conductivity. In addition, highly reflective coatings, which reduce the thermal load of the parts from radiation, can be produced. Further applications of SPS coatings as cathode layers in solid oxide fuel cells (SOFC) and for photovoltaic (PV) applications will be presented.     

Effective Parameters in Axial Injection Suspension Plasma Spray Process of Alumina-Zirconia Ceramics

Suspension plasma spray (SPS) is a novel process for producing nano-structured coatings with metastable phases using significantly smaller particles as compared to conventional thermal spraying. Considering the complexity of the system there is an extensive need to better understand the relationship between plasma spray conditions and resulting coating microstructure and defects. In this study, an alumina/8 wt.% yttria-stabilized zirconia was deposited by axial injection SPS process. The effects of principal deposition parameters on the microstructural features are evaluated using the Taguchi design of experiment. The microstructural features include microcracks, porosities, and deposition rate. To better understand the role of the spray parameters, in-flight particle characteristics, i.e., temperature and velocity were also measured. The role of the porosity in this multicomponent structure is studied as well. The results indicate that thermal diffusivity of the coatings, an important property for potential thermal barrier applications, is barely affected by the changes in porosity content.     

3D Analysis of Porosity in a Ceramic Coating Using X-ray Microscopy

Suspension plasma spraying (SPS) is a new, innovative plasma spray technique using a feedstock consisting of fine powder particles suspended in a liquid. Using SPS, ceramic coatings with columnar microstructures have been produced which are used as topcoats in thermal barrier coatings. The microstructure contains a wide pore size range consisting of inter-columnar spacings, micro-pores and nano-pores. Hence, determination of total porosity and pore size distribution is a challenge. Here, x-ray microscopy (XRM) has been applied for describing the complex pore space of the coatings because of its capability to image the (local) porosity within the coating in 3D at a resolution down to 50 nm. The possibility to quantitatively segment the analyzed volume allows analysis of both open and closed porosity. For an yttria-stabilized zirconia coating with feathery microstructure, both open and closed porosity were determined and it could be revealed that 11% of the pore volumes (1.4% of the total volume) are closed pores. The analyzed volume was reconstructed to illustrate the distribution of open and closed pores in 3D. Moreover, pore widths and pore volumes were determined. The results on the complex pore space obtained by XRM are discussed in connection with other porosimetry techniques.     

环氧富Zn-Al-Mg-Ce合金涂层耐腐蚀性能

采用悬浮液等离子喷涂(SPS)和常规等离子喷涂(CPS)2种工艺制备纳米结构ZrO2/Y2O3涂层。利用XRD和SEM分析涂层的物相和微观组织,同时使用韦伯分布函数对涂层的显微硬度进行了统计分析。研究结果表明:在试验条件下,SPS制备的纳米结构ZrO2/Y2O3涂层为粒状结构,涂层致密且没有观察到显微裂纹。单个层片直径在0.3～4μm之间,平均晶粒尺寸51.8nm。CPS制备的纳米结构ZrO2/Y2O3涂层由部分熔化区和全熔区组成,部分熔化区保持纳米结构。2种方法制备的涂层物相均为亚稳四方相。CPS纳米结构涂层的显微硬度韦伯图呈双态分布,其中全熔区显微硬度较高,离散性大,而部分熔化区显微硬度低,离散性较小。SPS涂层显微硬度离散性比CPS全熔区小,表明SPS涂层组织更为均匀。     

Comparison Between High-Velocity Suspension Flame Spraying and Suspension Plasma Spraying of Alumina

Two different spray processes??suspension plasma spraying (SPS) and high-velocity suspension flame spraying (HVSFS)??are under focus in the field of suspension spraying. Both techniques are suitable for manufacturing finely structured coatings. The differences in the particle velocity and temperature of these two processes cause varying coating characteristics. The high particle velocity of the HVSFS process leads to more dense coatings with low porosity values. Coatings with a higher and also homogeneous porosity, which can be generated by SPS, have also high potential, for example, for thermal barrier coatings. In this study, both the processes??SPS and HVSFS??were compared using alumina as feedstock material mixed with different solvents. Besides the characterization of the microstructure and phase composition of the applied coatings, the focus of this study was the investigation of the melting behavior of the particles in-flight and of single splat characteristics.     

A comparative study of tribological behavior of plasma and D-gun sprayed coatings under different wear modes

In recent years, thermal sprayed protective coatings have gained widespread acceptance for a variety of industrial applications. A vast majority of these applications involve the use of thermal sprayed coatings to combat wear. While plasma spraying is the most versatile variant of all the thermal spray processes, the detonation gun (D-gun) coatings have been a novelty until recently because of their proprietary nature. The present study is aimed at comparing the tribological behavior of coatings deposited using the two above techniques by focusing on some popular coating materials that are widely adopted for wear resistant applications, namely, WC-12% Co, A1₂O₃, and Cr₃C₂-MCr. To enable a comprehensive comparison of the above indicated thermal spray techniques as well as coating materials, the deposited coatings were extensively characterized employing microstructural evaluation, microhardness measurements, and XRD analysis for phase constitution. The behavior of these coatings under different wear modes was also evaluated by determining their tribological performance when subjected to solid particle erosion tests, rubber wheel sand abrasion tests, and pin-on-disk sliding wear tests. The results from the above tests are discussed here. It is evident that the D-gun sprayed coatings consistently exhibit denser microstructures and higher hardness values than their plasma sprayed counterparts. The D-gun coatings are also found to unfailingly exhibit superior tribological performance superior to the corresponding plasma sprayed coatings in all wear tests. Among all the coating materials studied, D-gun sprayed WC-12%Co, in general, yields the best performance under different modes of wear, whereas plasma sprayed Al₂O₃ shows least wear resistance to every wear mode.     

An analytical model for simulation of heat flow in plasma-sprayed thermal barrier coatings

Numerical (finite difference) and analytical models have been developed for the simulation of heat flow through plasma-sprayed coatings, allowing the effective thermal conductivity to be predicted as a function of microstructural parameters. The structure is assumed to be composed of lamellar material (splats), separated by (thin) pores, within which there are areas of contact (bridges). The analytical model is based on dividing the material into two regimes, within which the heat flow occurs either by unidirectional serial flow through lamellae and pores or by being funneled through the regions of the lamellae above and below the bridges. The validity of this model is demonstrated by a comparison of the predictions obtained from it and those obtained from the numerical model. The effects of pore geometry on conductive and radiative heat transfer within the coating have been investigated over a range of temperatures and gas pressures. It is shown that the main factor controlling the conductivity is the intersplat bridge area. Comparisons are also presented with experimental conductivity data, for cases in which some attempt has been made to characterize the key microstructural features. The study is oriented toward thermal barrier coatings, based on zirconiayttria top coats. It is noted that the effect of microstructural sintering, which tends to occur in these coatings under service conditions, can be predicted using this model.     

Laboratory report—thermal spraying at the shanghai institute of ceramics

Plasma spraying has received considerable attention as a process for obtaining protective coatings. In this article, experiments and results obtained at the Shanghai Institute of Ceramics pertaining to the developments and application of plasma-sprayed coating materials such as thermal barrier, wear resistance, infrared radiation, electrode materials, biomedical materials, and diamond films are presented. The physical, mechanical, and thermal properties of the coatings were measured. The microstructural features of the coatings were also examined. Examples of applications of plasma-sprayed coatings in various industries are illustrated. In addition, the manufacture of some oxide powders and their characteristics are discussed.     

Manufacturing Process of Nanostructured Alumina Coatings by Suspension Plasma Spraying

This paper describes the formation process of nanostructured alumina coatings and the injection system obtained by suspension plasma spraying (SPS), an alternative to the atmospheric plasma spraying technique in which the material feedstock is a suspension of the nanopowder to be sprayed. The nanoscale alumina powders (d ≈ 20 nm) were dispersed in distilled water or ethanol and injected by a peristaltic pump into plasma under atmospheric conditions. Optical microscopy (OM), scanning electron microscopy (SEM), and x-ray diffraction (XRD) analyses were performed to study the microstructure of the nanostructured alumina coatings. The results showed that the nanoscale alumina powders in suspension were very easily adsorbed at the inner surface of injection, which caused the needle to jam. The rotation of the pump had a great effect on the suspension injection in the plasma. The very small resistance of the thin plasma boundary layer near the substrate can drastically decrease the impacting velocity of nanosize droplets. The concentration of suspension also has a significant influence on the distribution of the size of the droplet, the enthalpy needed for spraying suspension, and the roughness of the coating surface. The phase structures of alumina suspension coatings strongly depend on the plasma spraying distance. A significant nanostructured fine alumina coating was obtained in some areas when ethanol was used as a solvent. The microstructures of the coating were observed as a function of the solvent and the spraying parameters.     

悬浮液等离子喷涂热障涂层研究进展

悬浮液等离子喷涂(SPS)解决了纳米尺度粉末输送困难的问题,在热喷涂领域得到了快速发展。介绍了悬浮液等离子喷涂的原理和特点,综述了不同工艺条件对热障涂层结构的影响:降低弧电压的波动可以提高SPS工艺的可控性;降低喷枪功率、降低悬浮液浓度、增大喷涂距离,可实现涂层由垂直裂纹结构向柱状晶结构的演变;降低表面粗糙度可提高柱状晶的均匀性;溶剂为乙醇、溶质粒度分布合理的悬浮液更容易获得柱状晶结构。总结了SPS制备热障涂层产生垂直裂纹结构和类柱状晶结构的机理,认为在相同表面粗糙度下,熔滴尺寸和切向速度是影响涂层结构的关键。SPS-8YSZ涂层的隔热性能和热循环性能较好,具有良好的应用前景。