共查询到20条相似文献,搜索用时 78 毫秒
1.
含硫原油炼制过程中活性硫腐蚀 总被引:29,自引:3,他引:26
原油主要由碳氢化合物构成 ,并含有相当数量的有害杂质 ,其中硫化合物等在原油炼制过程中对炼制设备有较为严重的腐蚀作用 .对含硫原油炼制过程中硫的主要存在形成以及活性硫的由来进行了分析讨论 ,并阐述了炼制过程活性硫析出对腐蚀过程的加速作用 .为了对含硫原油在炼制过程中复杂的硫腐蚀过程和规律的深入认识 ,指出了应发展相应的在线监 /检测技术以及开展系统的研究工作 . 相似文献
2.
本文简要介绍了对于炼制高硫原油的加氢装置中设备常见的腐蚀,初步分析了腐蚀产生的机理并介绍了一些防腐措施。 相似文献
3.
4.
5.
储罐在原油生产、炼制、成品油销售及石油战略储备中发挥重要作用,罐体金属腐蚀影响储罐使用寿命、危及储罐使用安全,必须进行防治。为此,介绍了原油中硫的存在形式及腐蚀特性,分析了储罐不同部位腐蚀机理,针对性提出了相应的防腐蚀措施,具有一定借鉴意义。 相似文献
6.
国产原油大部分含硫低,只有胜利和江汉原油含硫略高,所以硫对设备的腐蚀研究较少.由于原油产量供不上炼油厂的需要,加工国外合硫原油逐年增加,特别是加工中东高硫原油量大,茂名炼油厂1993年加工中东油占总产量的50%左右,今后进口原油还要增加.因此原油含硫对设备的腐蚀应当引起关注.1 原油的性质在石油工业中,一般把含硫小于0.1%的原油称超低硫原油,含硫为0.1~0.5%的原油称低硫原油.含硫大于0.5%的原油称高硫原油.如果把酸值大于0.5mg KOH/g的原油称高酸原油,那么,华北、中原、大庆原油 相似文献
7.
8.
几种材料在高酸值原油中的腐蚀 总被引:1,自引:0,他引:1
通过对非洲某高酸值原油、脱盐原油、原油馏分油、常压渣油、脱酸原油、减粘渣油及减粘渣油馏分油的实验室腐蚀模拟试验,以及对试验试样的表面形态、表面成分的观察和分析,研究了碳钢、渗铝钢、Cr5Mo及不锈钢在高酸值原油中的腐蚀规律,对影响腐蚀速率的因素进行了探讨,研究结果对炼制此类原油的设备选材及确定防腐蚀方案具有广泛的参考意义,某装置根据这一研究结果选材,节省投资数千万元.
相似文献
9.
近年以来,由于我国原油变重及含硫、含氮、酸值的增加,以及引进中东高含硫的原油,更加重了炼油设备的腐蚀.原油中或多或少地含有硫化物,通常将含硫量在0.1%~0.5%的原油称为低硫原油;含硫量大于0.5%者为高硫原油.一般,原油中的总含硫量与腐蚀性能之间并无精确的关系,主要参与腐蚀反应的有效硫化物有H2S、单质硫、硫醇等活性硫及易分解为H2S的硫化物,这类硫化物含量越高,对设备的腐蚀就越强. 相似文献
10.
近几年来 ,随着加工高硫原油的不断增加 ,炼油装置设备、管道的腐蚀日益加重 ,导致一系列由硫腐蚀引发的各类事故和潜伏的隐患 ,给安全生产带来了很大的危害。那么 ,如何尽快解决好高硫原油的腐蚀问题呢 ?在解决这个问题的过程中 ,防腐蚀技术协会应如何发挥作用 ?带着这些问题 ,笔者最近采访了中国化工防腐蚀技术协会副理事长、中国石油化工股份有限公司科技开发部副主任周培荣。周副理事长首先介绍了我国石油加工的现状。他说 ,近几年来 ,由于国内原油产量增加的难度越来越大 ,国内原油产量已不能满足原油加工能力的需求。进口原油加工量逐… 相似文献
11.
加工表面质量对材料表面耐腐蚀性能的影响具有复杂性和综合性,研究加工表面质量对材料表面耐腐蚀性能的影响,对如何延长机械产品的服役寿命、预测加工表面质量、精简制造工序和优化加工参数等具有重要的指导和实践作用。对已加工表面腐蚀形成机理进行了分析,并指出了影响耐腐蚀性能的因素,从加工表面机械物理特征和加工表面几何形状特征两方面入手,综述了已加工表面质量对耐腐蚀性能影响的研究进展。重点报道了加工表面机械物理特征中表面残余应力、加工表面金相组织变化以及加工表面冷作硬化对耐腐蚀性能影响的研究进展,分别总结了加工表面几何形状特征中已加工表面的表面纹理、表面粗糙度和表面伤痕对耐腐蚀性能影响的研究进展。提出应开展多表面质量参数之间相互影响综合分析,以及各表面质量参数联合作用下对表面耐腐蚀性能影响的研究,为开展表面质量与金属材料加工表面耐腐蚀性能关联性研究打下基础,并指出了加工表面质量对耐腐蚀性能影响研究的未来发展趋势。 相似文献
12.
溶质元素在金属晶界的偏聚可以分为两类,即平衡偏聚和非平衡偏聚。本文回顾了这两类偏聚现象及其机理,着重讨论分析了有重要工程用途的三类典型的晶界偏聚:硼在奥氏体晶界的两类偏聚的实验规律及对硼钢淬透性影响;磷在奥氏体晶界的平衡偏聚及对钢回火脆性的作用,钢中的其他合金元素对磷的偏聚的影响;硼在多种金属间化合物的偏聚及对这些金属间化合物塑性的影响及其机理。 相似文献
13.
《稀有金属材料与工程》2012,(Z1):380-383
The performance of copper coatings fabricated on three substrates by LTHVOF spraying process was researched.XRD shows that substrate material has little effect on phase composition of coatings,and there is no oxide in the three coatings almost.These coatings are dense,and demonstrate little difference on the microstructure of the inner part of the coatings.However,microstructure of bonding area between coating and substrate shows big difference,copper coatings bonds compacter on soft substrate aluminum than hard substrate steel.Bonding strength of coatings sprayed on the soft substrate is higher than that on the hard substrate.Microstructure analysis of fracture surface shows that strong mechanical alloying phenomena when copper particles deposited on aluminum substrate.The average bonding strength of copper coatings on 1Cr18Ni9Ti,45#steel and LY12 is relatively 18.83,17.49 and 32.14 MPa.Substrates have strong effect on microstructure and bonding strength,but little on phase composition... 相似文献
14.
大块非晶合金超塑性变形的研究现状与发展 总被引:1,自引:0,他引:1
文章对国内外非晶合金超塑性基本性能的研究工作进行了介绍和评述。根据材料成形工艺的要求,提出了非晶合金超塑性成形研究的内容。介绍了非晶合金超塑性拉伸实验和压缩实验的研究进展,分析了温度和成形速率对变形的影响,介绍了粘度的影响因素,对这些研究内容和热点问题进行了评述。展望了非晶合金超塑性研究的发展趋势,提出应加强非晶合金超塑性流动过程的理论研究。 相似文献
15.
An impedance response model reflecting the inhibitory effect of antibiotics on bacterial growth in biomet-allurgy was established. Three inhibition parameters, i.e. the maximum amount inhibitory constant of the bacterial growth(K1), the maximum specific growth inhibitory constant(K2) and the lag time inhibitory constant(K3), were included in the model. The influence of these parameters on the response curve was discussed in detail. By fitting experimental data towards the proposed model, three growth parameters (A,μm and λ) in the presence of antibiotics were gained and compared. The results show that the growth ability of bacteria is decreased due to the influence of antibiotics. The experimental and fitted curves have goodness-of-fit in the range of 0. 987-1. 008. Moreover, the kinetic growth parameters obtained from this model are closed to those from the Logistics popular growth model.These results show that the proposed model is validity to reflect the inhibitory effect of antibiotics on bacteria. 相似文献
16.
板料马鞍形曲面的无模多点成形实验研究 总被引:3,自引:0,他引:3
在自制的多点模实验装置上对马鞍形曲面的成形进行了实验 ,并分析了实验过程中产生的压痕和失稳的分布规律及弹性垫对成形的影响 ,总结出了使用弹性垫抑制缺陷及采用逐次成形法提高板料成形极限的方法。 相似文献
17.
从成像过程基本理论,给出了等价性问题概念,具体讨论了等价性指标、等价性级别问题,给出了等价性范围讨论的思路、方法,并以矩形函数近似扩散函数为例,说明了讨论等价性厚度范围的过程。 相似文献
18.
19.
目的:拟观察不同吸入麻醉药对新生期大鼠神经胶质细胞增殖活化的影响。方法:新生大鼠于出生后第2天(P2)暴露于异氟醚、七氟醚或地氟醚处理2 h,并分别于出生后第7天(P7)或第14天(P14)取材,通过免疫荧光或免疫组化的方法,检测不同胶质细胞标记物(vimentin, GFAP, Iba1)在新生大鼠海马不同亚区的分布及表达。结果:大鼠在新生期(P2)单次暴露于不同吸入麻醉药,地氟醚组海马齿状回颗粒层及分子层成熟星形胶质细胞在P7及P14活化显著增强,异氟醚组仅在P14差异具有统计学意义。地氟醚组海马齿状回颗粒层而非CA1区锥体细胞层小胶质细胞在P7及P14活化显著增强,异氟醚组仅在P14存在统计学差异。 结论:不同吸入麻醉药短时间单次处理出生后第2天新生大鼠,对海马不同亚区胶质细胞的活化存在不同作用,七氟醚可能对其影响最小。 相似文献
20.
《中国有色金属学会会刊》2021,31(8):2307-2322
The composition of magnesium alloys is greatly associated with initial deposition behavior of electroless Ni–P coatings. Thus, the initial deposition behavior of electroless Ni–P coatings on ZK60 and ME20 alloys was investigated. The results indicated that differences in the alloy compositions significantly influenced the initial deposition process and the adhesive strength, corrosion resistance, and crystal structure. The initial deposition of coatings on ZK60 and ME20 alloys preferentially occurred on the precipitates. The precipitates in ZK60 alloy had higher chemical activity after HF activation and controlled the initial deposition rate of the coating. The initial deposition rate of the coating on ME20 alloy mainly depended on the density of the MgF2 film formed by HF activation rather than on the precipitates. Owing to differences in the initial deposition process, the coating on ZK60 alloy had higher adhesive strength and better corrosion resistance than that on ME20 alloy. The coatings on ZK60 and ME20 alloys mainly had crystalline structures, and the coating on ME20 alloy had also a slight microcrystalline structure. 相似文献