锡基稀溶液中Ca和Mg的自身作用系数

在1500℃下以金属Sn作熔剂,石墨作还原剂,采用相同组成熔渣与不同组成的锡合金在CO-Ar混合气体条件下,使反应达到平衡,测定了锡基稀溶液中Ca,Ti和Mg的自身和相互作用系数。指出在用此法测定熔渣中组元的活度时,忽略Sn中元素的自身作用系数,将带来较大误差。     

ACTIVITIES OF COMPONENTS IN MgO-B_2O_3 MELT

本文以Sn作为金属熔剂,石墨作为还原剂用,“渣-金”化学平衡法在1500和1550℃下,测定了MgO-B_2O_3二元系熔渣中Mgo的活度,并采用α函数积分法求得了该二元系熔渣中B_2O_3的活度。此外,由B_2O_3和MgO的活度数据估算了复合化合物2MgO·B_2O_3和3MgO·B_2O_3的标准生成自由能。     

CaO-SiO_2-Al_2O_3熔渣中CaO的活度

本文以Sn为溶剂金属,直接用“渣-金属”化学平衡法,在较大组成范围内测定了CaO-Si0_2-Al_2O_3三元熔渣中CaO的活度。成功地用图示推测法推测了较难直接获得实验结果的低CaO浓度范围内CaO的活度。应用本文实验结果和数据分析得到了该渣系中较全面的等CaO活度曲线图,并对Al_2O_3在该渣系中的酸碱性行为进行了探讨。     

ACTIVITY OF CaO IN LIQUID CaO-SiO_4-Al_2O_3 SYSTEM

本文以Sn为溶剂金属,直接用“渣-金属”化学平衡法,在较大组成范围内测定了CaO-Si0_2-Al_2O_3三元熔渣中CaO的活度。成功地用图示推测法推测了较难直接获得实验结果的低CaO浓度范围内CaO的活度。应用本文实验结果和数据分析得到了该渣系中较全面的等CaO活度曲线图,并对Al_2O_3在该渣系中的酸碱性行为进行了探讨。     

SOME ASPECTS OF THE THERMODYNAMICS OF MELTS

为了从二元系中两组元活度的测定值之比求得该两组元的活度值,导出了一个变通的 Gibbs-Duhem 方程式,并在 PbCl_2-SnCl_2,PbCl_2-CdCl_2,AgCl-CuCl,Cu_2S-FeS,PbO-BiO_(1.5),PbO-SbO_(1.5),CaO-CaF_2及 CaO-SiO_2-CaF_2等冶金熔体中得到应用.多年前所发展的从 Ag 和 Pb 二元相图求得两组元活度的方法已扩大到含有单个 AB 化合物的二元系.用这一方法已求得 In-Sb 和 Sn-Te 系中各组元的活度.在研究某些黑色冶金渣与金属间的平衡时,用一适当选择的非铁金属代替 Fe作为熔剂金属有助于克服某些实验上的困难.采用 Sn 或 Cu 与熔渣平衡研究了 CaO-SiO_2,CaO-Al_2O_3和 CaO-SiO_2-Al_2O_3体系.对 CaO-SiO_2二元系获得的数据可以认为具有足够的准确度来验证 Masson 模型的合理性.     

冶金熔体热力学的若干研究

为了从二元系中两组元活度的测定值之比求得该两组元的活度值,导出了一个变通的 Gibbs-Duhem 方程式,并在 PbCl_2-SnCl_2,PbCl_2-CdCl_2,AgCl-CuCl,Cu_2S-FeS,PbO-BiO_(1.5),PbO-SbO_(1.5),CaO-CaF_2及 CaO-SiO_2-CaF_2等冶金熔体中得到应用.多年前所发展的从 Ag 和 Pb 二元相图求得两组元活度的方法已扩大到含有单个 AB 化合物的二元系.用这一方法已求得 In-Sb 和 Sn-Te 系中各组元的活度.在研究某些黑色冶金渣与金属间的平衡时,用一适当选择的非铁金属代替 Fe作为熔剂金属有助于克服某些实验上的困难.采用 Sn 或 Cu 与熔渣平衡研究了 CaO-SiO_2,CaO-Al_2O_3和 CaO-SiO_2-Al_2O_3体系.对 CaO-SiO_2二元系获得的数据可以认为具有足够的准确度来验证 Masson 模型的合理性.     

含挥发组分B_2O_3渣系活度的测定方法

本文以Ｓｎ作熔剂，以石墨作坩埚，在一个半密闭的石墨容器内，用“熔渣－金属”化学平衡法测定了含挥发性组分Ｂ２Ｏ３的ＣａＯ－Ｂ２Ｏ３二元系中ＣａＯ的活度；用α函数积分法计算了Ｂ２Ｏ３的活度．实验结果与文献报道的利用相图和生成自由能计算得到的数据相符．     

含挥发组分B_2O_3渣系活度的测定方法SCIEI

本文以Ｓｎ作熔剂，以石墨作坩埚，在一个半密闭的石墨容器内，用“熔渣－金属”化学平衡法测定了含挥发性组分Ｂ２Ｏ３的ＣａＯ－Ｂ２Ｏ３二元系中ＣａＯ的活度；用α函数积分法计算了Ｂ２Ｏ３的活度．实验结果与文献报道的利用相图和生成自由能计算得到的数据相符．     

A STUDY ON THE TITANIUM LOSS DURING ELECTROSLAG REMELTING HIGH TITANIUM AND LOW ALUMINUM CONTENT SUPERALLOY

研究A286和V57合金电渣重熔过程中钛烧损时,发现渣中TiO_2浓度较高时,TiO_2是钛烧损的主要氧化剂。与合金中的钛相平衡的渣中低价钛氧化物主要是Ti_3O_5.决定钛烧损速率的主要因素是Ti~(4+)在钢/渣界面层的传质速度。传质速度随渣中TiO_2浓度的增加而增大。降低Ti~(3+)向渣/气界面的扩散速度是减少合金中钛烧损的关键。研究了CaF_2-Al_2O_3-TiO_2渣系中Ti~(4+)在电极/熔渣和金属熔池/熔渣界面在1700±10℃的传质系数与渣中TiO_2含量的关系,测定了Ti~(3+)向渣/气界面的传质系数为2.2×10~(-1)cm/s(1500℃)。     

高钛低铝高温合金电渣重熔中钛烧损的研究

研究A286和V57合金电渣重熔过程中钛烧损时,发现渣中TiO_2浓度较高时,TiO_2是钛烧损的主要氧化剂。与合金中的钛相平衡的渣中低价钛氧化物主要是Ti_3O_5.决定钛烧损速率的主要因素是Ti~(4 )在钢/渣界面层的传质速度。传质速度随渣中TiO_2浓度的增加而增大。降低Ti~(3 )向渣/气界面的扩散速度是减少合金中钛烧损的关键。研究了CaF_2-Al_2O_3-TiO_2渣系中Ti~(4 )在电极/熔渣和金属熔池/熔渣界面在1700±10℃的传质系数与渣中TiO_2含量的关系,测定了Ti~(3 )向渣/气界面的传质系数为2.2×10~(-1)cm/s(1500℃)。     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Rheology Feature of Simple Metal Melt

The rheology feature of Sb, Bi melt and alloys was studied using coaxial cylinder high-temperature viscometer. The results showed that the curve of torsion-rotational speed for Sb melt presents a linear relation in all measured temperature ranges, whereas for the Bi melt, the curve presents obvious non-Newtonian feature within the low temperature range and at relative high shear stress. The rheology feature of Sb80Bi20 and Sb20Bi80 alloy melts was well correlated with that of Sb and Bi, respectively. It is considered that the rheology behavior of Sb melt plays a crucial role in Sb80Bi20 alloy and that of Bi melt plays a crucial role in Sb20Bi80 alloy.     

Microstructures and Mechanical Properties of a Newly Developed Austenitic Heat Resistant Steel

The effect of heat treatment on the microstructures and mechanical properties of a newly developed austenitic heat resistant steel(named as T8 alloy) for ultra-supercritical applications have been studied. Results show that the main phases in the alloy after solution treatment are γ and primary MX. Subsequent aging treatment causes the precipitation of M_(23)C_6 carbides along the grain boundaries and a small number of nanoscale MX inside the grains. In addition, with increasing the aging temperature and time, the morphology of M_(23)C_6 carbides changes from semi-continuous chain to continuous network.Compared with a commercial HR3C alloy, T8 alloy has comparable tensile strength, but higher stress rupture strength. The dominant cracking mechanism of the alloy during tensile test at room temperature is transgranular, while at high temperature, intergranular cracking becomes the main cracking mode, which may be caused by the precipitation of continuous M_(23)C_6 carbides along the grain boundaries. Typical intergranular cracking is the dominant cracking mode of the alloy at all stress rupture tests.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

The 15th Global Foundry Sourcing Conference 2014held in Qingdao China

Organized by Suppliers China Co., Ltd and co-organized by the National Technical Committee 54 on Foundry of Standardization Administration of China, the 15th Global Foundry Sourcing Conference 2014 （hereinafter referred to as FSC 2014） was successfully held on Sep. 23rd in Grand Regency Hotel, Qingdao. More than 500 delegates from home and abroad attended this conference, including over 130 purchasers from 20 countries and 380 domestic and foreign suppliers.     

Secondary Recrystallization Behaviors of Grain-Oriented 6.5 wt% Silicon Steel Sheets Produced by Rolling and Nitriding Processes

By rolling and nitriding processes, 0.23- to 0.3-mm-thick grain-oriented 6.5 wt% silicon steel sheets were produced. The core losses of grain-oriented 6.5 wt% silicon steel at frequencies ranging from 400 Hz to 20 k Hz were lower than that of the grain-oriented 3 wt% silicon steel with the same thickness by 16.6–35.8%. The secondary recrystallization behavior was investigated by scanning electron microscopy, energy-dispersive spectroscopy, and electron backscattered diffraction. The results show that the secondary recrystallization in high-silicon steel sheets develops more completely as the nitrogen content increases after nitriding, secondary recrystallized grain sizes become larger, and the sharpness of Goss texture increases. Because more {110}116 grains in the subsurface and the central layer of the sheets have a lot of 20°–45° high-energy boundaries in addition to Goss grains, {110}116 can be the main component through selective growth during secondary recrystallization when the inhibitor quantity is not enough and inhibitor intensity is weaker. The increases in nitrogen content can increase the inhibitor intensity and hinder abnormal growth of a mount of {110}116 grains and therefore enhance the sharpness of Goss texture.     

Laser Cladded TiCN Coatings on the Surface of Titanium

Laser cladded coatings of TiCN were produced on the surface of titanium. To obtain the optimal techniques, several conditions were tested by varying the laser scanning rate. The choice of shielding gas was also studied. The cladded coatings were then evaluated from the surface mechanics point of view based on their microhardness. The microstructure of some interesting samples was investigated by optical micrographs (OM). The results showed that under the condition of fixed pulse frequency and pulse width, the laser scanning rate and the shielding gas are the main factors influencing the components of coatings. TiCN coatings were decompounded and oxidized during the cladding process in the condition of no shielding gas of N2. X-ray diffraction results indicated that the composite coatings composed of TiCN, TiC, Ti2N, and TiO2 were produced using appropriate techniques. The results indicated that the best condition in terms of the surface microhardness is obtained when the scanning rate is 1.5mm / s, the pulse frequency is 15Hz, the pulse width is 3.0ms, and N2 is chosen as the shielding gas. The microhardness of the composite coatings is about 1331kg · mm - 2, which is about 4 times that of the substrate. The optical micrographs indicated that the cladding zone is made up of TiCN, TiO2, and some interdendritic Ti, but the diffusion zone mainly consists of the dendrites phase, and the cladded depth is about 80?滋m, which is more than 2 times that of the laser nitrided sample. There were no microcracks or air bubbles in the cladded sample, which was cladded using the above optimal techniques.     

Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel 2002

The effect of short-time aging in the temperature range between 400 and 1000 °C on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel(LDSS) 2002 was investigated through the potentiostatic critical pitting temperature(CPT) tests and the Charpy impact tests. Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 °C concurrently. The CPT of LDSS 2002 specimen aged at 650 °C decreased by 28 °C, and the impact energy dropped from 69 to 29 J/cm~2 compared with the solution-annealed sample. Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr_2N and M_(23)C_6 along the ferrite–austenite grain boundaries.     

Information for Contributors

正The Transactions of Nonferrous Metals Society of China,founded in 1991 and sponsored by The Nonferrous Metals Society of China,is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology,including mineral processing,extraction metallurgy,metallic materials and heat treatments,metal working,physical metallurgy,powder metallurgy,with the emphasis