首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
0Cr18Ni10Ti奥氏体不锈钢管道焊接的操作难点及对策   总被引:1,自引:0,他引:1  
郭强 《焊接》2003,(2):41-42
针对工作温度 - 4 0~ - 12 0℃ ,管径范围DN2 5~70 0mm的 0Cr18Ni10Ti奥氏体不锈钢 ,壁厚范围 3~ 8mm的 0Cr18Ni10Ti奥氏体不锈钢管道 ,通过对该不锈钢焊接行为的分析研究及工艺评定结果 ,结合工程实践 ,我们总结归纳了一整套奥氏体不锈钢管道焊接的操作工艺规程及其要点。1 焊接工艺方法及材料(1)壁厚δ≤ 4mm且公称直径≤ 5 0mm的焊口 ,采用钨极氩弧焊工艺 ,焊丝牌号为H0 0Cr2 1Ni10。(2 )壁厚δ >4mm或公称直径 >5 0mm的不锈钢管焊口 ,采用钨极氩弧焊打底、焊条电弧焊填充、盖面的焊接工艺。焊条牌号…  相似文献   

2.
黄晓霞 《焊接》2002,(11):45-47
外径为 2 10 0~ 2 30 0mm压力管道采用日本NKK公司生产的板厚为 2 8~ 5 4mm的HS610U -M高强钢焊制 ,其化学成分见表 1。根据该钢的碳当量Ceq和裂纹敏感系数Pcm,通过焊接工艺试验 ,制定了焊接工艺参数和相应的工艺措施 ,保证了焊接质量。1 认真做好焊前准备工作( 1)将坡口两侧各 5 0mm范围内的油漆、污物、毛剌等清理干净。( 2 )焊条在 4 0 0℃下烘干 1h。表 1 化学成分 (% )材质厚度CSiMnCuNiCrMoTiVBSHS610UHS610U -M2 6~ 4040~ 80≤ 0 .0 6≤ 0 .0 60 .2 50 .2 51.31.30 .170 .320 .3…  相似文献   

3.
316L不锈钢管道焊接工艺   总被引:3,自引:0,他引:3  
潘子祥 《焊接》2002,(12):36-37
我公司承担了攀钢煤化公司回收Ⅱ期脱酸蒸氨装置改造工程 ,该工程大部分是要求耐酸耐碱腐蚀的不锈钢管道 ,材质为 316L。工程质量的好坏 ,将直接影响到生产的安全运行。因此 ,制定合理有效的不锈钢焊接工艺是关键。1 焊接工艺( 1)焊接方法。由于现场多数为不锈钢管道 ,且大小不一 ,根据不锈钢的焊接特点 ,尽可能减小热输入量 ,故采用手工电弧焊、氩弧焊两种方法 ,d >15 9mm的采用氩弧焊打底 ,手工电弧焊盖面。d≤15 9mm的全用氩弧焊。焊机采用手工电弧焊 /氩弧焊两用的WS7-4 0 0逆变式弧焊机。( 2 )焊接材料。奥氏体不锈钢是…  相似文献   

4.
汽轮机动叶片 (以下称叶片 )的工作条件恶劣 ,对材料的要求苛刻 ,叶片的水蚀防护要求较高。为了降低制造成本 ,某电厂机组末级叶片采用在1Cr12Ni3Mo1VN (S/SJ2 )材料上高频钎焊司太立合金片的方法 ,替代 17- 4PH材质的叶片 ,既达到了防水蚀的要求又降低了制造成本。1 试件制备在 1Cr12Ni3Mo1VN长 4 30mm、宽 12 0mm、厚15mm的两块试板的一侧 ,加工出 2 6 0mm× 12mm凹槽。凹槽底部厚 2mm ,完全模拟正式生产中的叶片钎焊合金片凹槽尺寸。2 焊前准备 (1)按技术条件检查叶片及凹槽加工尺寸和质量 ,并进行…  相似文献   

5.
石高佩 《焊接》2001,(7):42-42
本公司安装的某厂热水系统管道介质为热水及蒸汽 ,材质为 2 0g ,2 19mm× 8mm规格的大口径管道对接接头为 2 0 6个。根据焊接工艺要求 ,决定采用氩弧焊打底 ,手工电弧焊盖面 ,以提高焊接一次合格率。1 焊接工艺参数(1)坡口形式 :V形坡口 ,α =65°± 5° ,b =1.5mm~ 2 .5mm ,p =0 .5mm~ 1.0mm。(2 )焊接工艺参数 :氩弧焊打底时 ,采用直流正接 ,手工电弧焊填充和盖面时 ,采用直流反接。具体工艺参数见表 1。2 气孔缺陷特征在正式施焊的第一天 ,对已焊完的 8个接头进行10 0 %的X光检验 ,结果均不合格。且出现如下特征…  相似文献   

6.
不锈钢真空钎焊接头组织和力学性能研究   总被引:3,自引:0,他引:3  
采用BNi-2、BNi-5、BDP~1、Cu四种不同钎料真空钎焊1Cr18Ni9Ti不锈钢,对其焊接接头的显微组织和力学性能进行了分析。结果表明:钎缝的组织与钎焊温度和钎料的成分等因素有关。使用BNi-2钎料钎焊得到的钎缝组织中出现了大量的化合物相;而采用BNi-5、BlIP-1钎料,钎缝中有少量化合物相;Cu钎焊时,钎缝中得到单相组织。BNi-2钎焊接头力学性能较差,而其余三种钎料钎焊接头力学性能较好,其中Cu钎焊接头性能最高。  相似文献   

7.
由于奥氏体不锈钢具有良好的成形性能和耐蚀性能等 ,所以在装修、钟表和人体直接接触的有关零部件中应用。但是 ,近年来发现奥氏体不锈钢中的Ni,会引起人体过敏 ,所以要求限制使用含Ni不锈钢制造与人体直接接触零部件。日本大同特殊钢公司等单位共同研制出添加N取代Ni的高锰不锈钢 ,商品名NFS。其试验材的化学成分 ( % ) :Fe— 0 0 2C— 1 8Mn <0 1Ni -1 6 0Cr- 0 43N。将轧制成5 2mm线材的试验钢在 1 2 73K进行固溶处理 ,然后取样供试验用。比较材选用市场购买的SUS430、 30 4和 31 6L奥氏体不锈钢。试验…  相似文献   

8.
Cr-Mo不锈钢复合板的焊接   总被引:1,自引:0,他引:1  
我公司为某化肥厂制造的气化炉主要受压元件材料为SA387Gr11CL2 /30 4L(δ =84mm + 4mm) ,由日本宇部工业兴产株式会社按ASME—Ⅱ (1989年版 )提供。该材料相当于 1.2 5Cr- 0 .5Mo耐热钢 ,焊接裂纹敏感性较高 ,焊接过程易产生冷裂纹。为满足复合板焊后复层的含碳量不大于 0 .0 2 %的要求 ,必须选择合理的焊接材料和焊接工艺。1 焊接材料与焊接方法SA387Gr11CL2 /30 4L钢淬硬倾向较大 ,焊接冷却过程中 ,熔合区和热影响区易产生马氏体组织 ,为避免产生马氏体组织 ,保证焊接接头的力学性能 ,采用SMAW +NGSA…  相似文献   

9.
激光淬火大圆弧剪刃的失效分析   总被引:1,自引:0,他引:1  
大圆弧剪刃材质为 4Cr5WMoSiV钢 ,化学成分 (质量分数 ,% )为 :0 4~ 0 5C ,4 75~ 5 5Cr,1 0~ 1 5Mo ,1 0~1 5W ,0 80~ 1 2 0Si,0 30~ 0 6 0V ,尺寸为 172 0mm×147mm× 90 2 5mm或 170 0mm× 177mm× 90 2 5mm。4Cr5WMoSiV  相似文献   

10.
不锈钢真空钎焊焊接接头的组织和力学性能   总被引:1,自引:1,他引:0  
主要对采用BNi-2、BNi-5、BIIP-1、Cu四种不同钎料的1Crl8Ni9Ti不锈钢真空钎焊焊接接头的显微组织和力学性能进行分析。结果表明:钎缝的组织与钎焊温度和钎料的成分等因素有关,在本次试验条件下,使用BNi-2钎料钎焊得到的钎缝组织中出现了大量的化合物相;而采用其余三种钎料,即BNi-5、BIIP-1和Cu钎焊时,其钎缝中只有少量的化合物相,钎缝接头的力学性能与其显微组织有关,使用BNi-2钎料钎焊的焊接接头力学性能较差,而其余三种钎料钎焊的焊接接头力学性能较好。上述试验结果可为研究真空钎焊提供必要的试验数据和理论依据。  相似文献   

11.
12.
13.
A synergetic approach to solution of problems of self-controlled synthesis of nanostructures and creation of self-organizing nanotechnologies is considered in connection with the superproblem of creation of materials with functional properties resembling those of biosystems. __________ Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 7, pp. 55 – 61, July, 2005.  相似文献   

14.
C. Colinet 《Intermetallics》2003,11(11-12):1095
A large number of ab-initio calculations of energies of formation of intermetallic compounds have been performed in the last 15 years. The currently used methods are listed. The paper presents a review of the aluminium based compounds which have been studied. Comparisons of calculated and experimental enthalpies of formation are provided for aluminim-3d and-4d transition metal alloys at equiatomic composition. The modelling of the enthalpies of mixing of solid solutions based on a given lattice is described.  相似文献   

15.
Conclusions To provide a high level of mechanical properties in wrought blanks of cast ÉP741NP and ÉP962 alloys it is necessary to form controlled structures. A necklace-type structure formed in homogenizing isostatic treatment, subsequent thermomechanical working including alternation of the operations of deformation in the (+)-area and recrystallization anneals, and final heat treatment is preferable. The temperature conditions of all stages of thermomechanical working are strictly controlled, especially the final operation of deformation and heating for hardening. To eliminate hardening cracks and distortions it is necessary to use molten salts at t=600°C as quenchants. The use of multiple production operations makes it possible to significantly reduce the structural inhomogeneity related to inhertance of the original dendritic structure. However, the structure of the final semifinished product is nevertheless characterized by a difference in occurrence of the processes of polygonization and recrystallization between the former dendritic cells and the interdendritic spaces in deformation and heat treatment.To obtain structurally homogeneous blanks for gas turbine engine parts it is necessary to use basically new methods of remelting such as vacuum double electrode remelting and electron beam remelting with an intermediate vessel.Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 12, pp. 25–29, December, 1991.  相似文献   

16.
The importance of the self-diffusion of a metal during its oxidation by a gas is treated for the cases of nonstoichiometric oxides having either interstitial cation or cation vacancies. We have established a general relationship for the reaction rate when a mixed diffusion process occurs. From this relationship, we have shown that the pressure dependence can be different, according to whether the rate-determining process is the self-diffusion through the metal or through the product.  相似文献   

17.
洋务派在洋务学堂的办学活动中,为了解决西学专业学科的教学困难,采用了聘请外籍教师的应急措施.他们以真才实学,合同制管理作为主导思想,并认为这种解决师资的途径只是权宜之计,并非久远.从客观上看,洋务派的教师聘任思想有深刻的历史影响.  相似文献   

18.
19.
刘兴  赵霞 《表面技术》2008,37(1):37-39
采用激光辐照对FeCrAlW电弧喷涂层的组织进行致密化处理,借助扫描电镜和X衍射对涂层的组织进行了分析.测试了涂层的显微硬度.结果表明:涂层组织致密度提高,孔隙率明显降低.随着激光扫描速度的增加,涂层的显微硬度降低.在较低的扫描速度下,涂层与基体之间形成互熔区,涂层与基体之间产生良好的冶金结合.  相似文献   

20.
论述了CAD技术中参数化设计的三种建模方法,重点介绍了基于特征的参数化建模原理。在此基础上,分析机械设计中的机构结构,归纳出其零件的几何特征构成。设计了机构CAD图形库,并提出了该图形库生成步骤和人机交互界面。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号