AZ31B镁合金在模拟流动海水中的腐蚀行为

利用质量损失法及X射线衍射（XRD）、扫描电镜（SEM）测试手段研究了铸态和挤压态AZ31B镁合金在模拟流动海水中浸泡12 h的腐蚀行为及随流速变化的规律。试验结果表明,AZ31B铸态镁合金试样的耐蚀性要远大于挤压态试样,且二者的腐蚀速率随搅拌速度增加的变化趋势有所不同：铸态试样的腐蚀速率随搅拌速度的增加近似呈线性上升,而挤压态试样的腐蚀速率随搅拌速度的增加而先增大后下降。     

挤压铸造制备半固态AZ61镁合金的组织演变及力学性能(英文)

采用挤压铸造后直接二次重熔的方法制备半固态AZ61镁合金。首先通过挤压铸造预成形铸态AZ61镁合金,以获得细小的枝晶;然后在半固态区间进行二次重熔,细小的枝晶演变成球状晶,完全球化的晶粒被液相均匀包裹。研究结果表明:通过挤压铸造预成形的铸态AZ61镁合金与传统铸造预成形的铸态AZ61镁合金相比,在相同的二次重熔条件下,挤压铸造预成形的铸态AZ61镁合金获得更细小的半固态组织。此外,挤压铸造加上二次重熔触变成形的AZ61镁合金,力学性能优于传统铸造后二次重熔触变成形的AZ61镁合金。     

挤压工艺对AZ31镁合金组织和性能的影响

研究了挤压温度和挤压速率对AZ31镁合金显微组织、耐腐蚀性能和力学性能的影响。结果表明,通过300℃下的热挤压变形,AZ31合金发生动态再结晶,合金组织比铸态时细化,耐腐蚀性能和力学性能明显提高;AZ31镁合金挤压后的组织及力学性能受挤压温度及挤压速率的影响,在本试验范围内,AZ31镁合金经过挤压温度为300℃、挤压速率为6.0 mm/s的挤压变形后得到的组织均匀细小,耐腐蚀性能和力学性能良好。     

钇对压铸AZ91镁合金耐腐蚀性能的影响

研究了在中性NaCl水溶液中压铸AZ91及AZ91 1%Y合金的腐蚀性能.结果表明,在相同浓度及相同温度的NaCl腐蚀介质中,压铸AZ91 1%Y合金的腐蚀速率明显低于AZ91合金.对压铸AZ91及AZ91 1%Y镁合金腐蚀层中各元素的XPS分析结果表明,AZ91 1%Y合金腐蚀试样中存在Y的氧化物,可以起到钝化保护膜的作用,从而提高了镁合金的耐腐蚀性能.     

Electrochemical Performance of AZ31 Magnesium Alloy under Different Processing Conditions

为选择一种高性价比的镁电池阳极材料,借助电化学工作站、光学显微镜(OM)、扫描电子显微镜(SEM)和X射线能谱分析(EDS)对不同加工状态的AZ31B镁合金电化学性能进行研究。分别将挤压、轧制、铸轧和铸态AZ31B镁合金作为阳极材料,测试其电化学性能。结果表明,在4种加工状态下,挤压态镁合金是性价比最高的一种阳极材料;其组织由均匀细小的晶粒和第二相组成,拥有最负的平衡电位,最低腐蚀电流密度和最小自腐蚀速率;挤压态样品腐蚀后,表面产生疏松细小,且均匀分布的腐蚀产物,降低了阳极极化,增加了阳极利用率。轧制和铸轧态的AZ31B镁合金的电化学活性和耐蚀性能相对挤压态的较低。铸态AZ31B镁合金由于较粗大的晶粒、第二相和铸造缺陷,表现出不稳定的放电曲线和较正的放电电位。不同状态AZ31镁合金的腐蚀均以点蚀为主。     

固溶时效处理对AZ31-0.6Sr镁合金腐蚀性能的影响

采用盐水浸泡试验研究了铸态(F)、500℃固溶(T4)和250℃时效16 h(T5)的AZ31-0.6Sr镁合金在w(NaCl)=3.5％溶液中的腐蚀行为.结果表明,铸态镁合金耐腐蚀性能最差,T5态耐腐蚀性能有所提升,T4态合金耐腐蚀性能最好.合金腐蚀速率随热处理状态的变化与其微观组织有关,铸态合金中的富Sr化合物能与基底α相构成电偶腐蚀而加剧合金腐蚀;T5态下出现了连续分布的β相能在一定程度上起腐蚀阻挡层作用,降低合金腐蚀速率.     

AZ61A镁合金搅拌摩擦焊接头在NaCl溶液中的腐蚀行为(英文)

对6mm厚的挤压态AZ61A镁合金板进行搅拌摩擦对接焊。采用浸泡试验研究焊接接头在NaCl溶液中的腐蚀行为,建立了一个经验公式来预测在不同的溶液pH值、浸泡时间和氯离子浓度下的接头腐蚀速率。该经验公式的可信度水平为95%。采用3因素、5水平的中央复合旋转设计方法来减少实验工作量。采用响应面方法来构建方程。结果表明,在碱性溶液中AZ61A镁合金接头的腐蚀速率要比其在酸性或中性溶液中的低,而且腐蚀速率随着氯离子浓度的降低和浸泡时间的延长而减少。β相的分布对其腐蚀形貌有重要影响。     

AZ31镁合金挤压板材的显微组织与力学性能研究

为了获得高性能镁合金板材,采用正向热挤压将铸态AZ31镁合金坯料挤压成2 mm厚的板材,研究了其显微组织演变及力学性能等。结果表明:铸态AZ31镁合金坯料挤压成板材后可以获得均匀细小的再结晶晶粒组织,其力学性能(屈服强度、抗拉强度、伸长率)大幅度提升。铸态AZ31镁合金坯料在400、450℃挤压成板材后,平均晶粒尺寸可由390μm分别细化至3.9、5.6μm。挤压后的AZ31镁合金板材展现出典型的(0001)基面织构,大部分晶粒的c轴垂直于板材表面。铸态AZ31镁合金的力学性能较差,而AZ31镁合金挤压板材在三个拉伸方向上均展现出优越的力学性能。随挤压温度的升高,AZ31镁合金挤压板材晶粒长大且显微组织不均匀,综合力学性能也有所下降。     

Er对铸态AZ91镁合金显微组织和耐腐蚀性能的影响

利用金相显微镜(OM)、扫描电镜(SEM)、能谱分析(EDS)、X射线衍射分析、集气法及动电位极化曲线研究了微量Er对铸态AZ91镁合金显微组织和腐蚀性能的影响.结果表明:微量Er可细化AZ91镁合金的铸态组织,当AZ91镁合金中加入Er的含量不高于0.7%(质量分数)时,随着Er含量的增加,镁合金中的γ-Mg17Al12相由粗大、连续块状分布逐渐转变为细小、岛状均匀分布,并且有Al3Er相生成;同时,微量Er也可显著提高铸态AZ91的耐腐蚀性能,当Er含量为0.7%时,合金耐蚀性能大幅度提高,在3.5%(质量分数)NaCl水溶液中浸泡的腐蚀速率为0.546 06 mg/(cm2·d),仅为常规AZ91镁合金的1/15;微量Er使得AZ91镁合金在3.5% NaCl溶液中的自腐蚀电位升高,自腐蚀电流降低,从而提高AZ91镁合金的耐腐蚀性能.     

汽车用AZ91镁合金的耐腐蚀性能

以AZ91镁合金为研究对象,研究了NaCl溶液的浓度、腐蚀时间、温度和搅拌速度对AZ91镁合金耐腐蚀性的影响。利用扫描电镜观察了腐蚀后的表面形貌和横截面形貌,定性分析了AZ91镁合金在NaCl溶液中的腐蚀行为。结果表明,随NaCl溶液浓度、腐蚀时间、温度和搅拌速度增加,AZ91镁合金腐蚀速率主要呈递增趋势,且腐蚀形式为沿晶腐蚀。     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Rheology Feature of Simple Metal Melt

The rheology feature of Sb, Bi melt and alloys was studied using coaxial cylinder high-temperature viscometer. The results showed that the curve of torsion-rotational speed for Sb melt presents a linear relation in all measured temperature ranges, whereas for the Bi melt, the curve presents obvious non-Newtonian feature within the low temperature range and at relative high shear stress. The rheology feature of Sb80Bi20 and Sb20Bi80 alloy melts was well correlated with that of Sb and Bi, respectively. It is considered that the rheology behavior of Sb melt plays a crucial role in Sb80Bi20 alloy and that of Bi melt plays a crucial role in Sb20Bi80 alloy.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Microstructures and Mechanical Properties of a Newly Developed Austenitic Heat Resistant Steel

The effect of heat treatment on the microstructures and mechanical properties of a newly developed austenitic heat resistant steel(named as T8 alloy) for ultra-supercritical applications have been studied. Results show that the main phases in the alloy after solution treatment are γ and primary MX. Subsequent aging treatment causes the precipitation of M_(23)C_6 carbides along the grain boundaries and a small number of nanoscale MX inside the grains. In addition, with increasing the aging temperature and time, the morphology of M_(23)C_6 carbides changes from semi-continuous chain to continuous network.Compared with a commercial HR3C alloy, T8 alloy has comparable tensile strength, but higher stress rupture strength. The dominant cracking mechanism of the alloy during tensile test at room temperature is transgranular, while at high temperature, intergranular cracking becomes the main cracking mode, which may be caused by the precipitation of continuous M_(23)C_6 carbides along the grain boundaries. Typical intergranular cracking is the dominant cracking mode of the alloy at all stress rupture tests.     

The 15th Global Foundry Sourcing Conference 2014held in Qingdao China

Organized by Suppliers China Co., Ltd and co-organized by the National Technical Committee 54 on Foundry of Standardization Administration of China, the 15th Global Foundry Sourcing Conference 2014 （hereinafter referred to as FSC 2014） was successfully held on Sep. 23rd in Grand Regency Hotel, Qingdao. More than 500 delegates from home and abroad attended this conference, including over 130 purchasers from 20 countries and 380 domestic and foreign suppliers.     

Secondary Recrystallization Behaviors of Grain-Oriented 6.5 wt% Silicon Steel Sheets Produced by Rolling and Nitriding Processes

By rolling and nitriding processes, 0.23- to 0.3-mm-thick grain-oriented 6.5 wt% silicon steel sheets were produced. The core losses of grain-oriented 6.5 wt% silicon steel at frequencies ranging from 400 Hz to 20 k Hz were lower than that of the grain-oriented 3 wt% silicon steel with the same thickness by 16.6–35.8%. The secondary recrystallization behavior was investigated by scanning electron microscopy, energy-dispersive spectroscopy, and electron backscattered diffraction. The results show that the secondary recrystallization in high-silicon steel sheets develops more completely as the nitrogen content increases after nitriding, secondary recrystallized grain sizes become larger, and the sharpness of Goss texture increases. Because more {110}116 grains in the subsurface and the central layer of the sheets have a lot of 20°–45° high-energy boundaries in addition to Goss grains, {110}116 can be the main component through selective growth during secondary recrystallization when the inhibitor quantity is not enough and inhibitor intensity is weaker. The increases in nitrogen content can increase the inhibitor intensity and hinder abnormal growth of a mount of {110}116 grains and therefore enhance the sharpness of Goss texture.     

Laser Cladded TiCN Coatings on the Surface of Titanium

Laser cladded coatings of TiCN were produced on the surface of titanium. To obtain the optimal techniques, several conditions were tested by varying the laser scanning rate. The choice of shielding gas was also studied. The cladded coatings were then evaluated from the surface mechanics point of view based on their microhardness. The microstructure of some interesting samples was investigated by optical micrographs (OM). The results showed that under the condition of fixed pulse frequency and pulse width, the laser scanning rate and the shielding gas are the main factors influencing the components of coatings. TiCN coatings were decompounded and oxidized during the cladding process in the condition of no shielding gas of N2. X-ray diffraction results indicated that the composite coatings composed of TiCN, TiC, Ti2N, and TiO2 were produced using appropriate techniques. The results indicated that the best condition in terms of the surface microhardness is obtained when the scanning rate is 1.5mm / s, the pulse frequency is 15Hz, the pulse width is 3.0ms, and N2 is chosen as the shielding gas. The microhardness of the composite coatings is about 1331kg · mm - 2, which is about 4 times that of the substrate. The optical micrographs indicated that the cladding zone is made up of TiCN, TiO2, and some interdendritic Ti, but the diffusion zone mainly consists of the dendrites phase, and the cladded depth is about 80?滋m, which is more than 2 times that of the laser nitrided sample. There were no microcracks or air bubbles in the cladded sample, which was cladded using the above optimal techniques.     

Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel 2002

The effect of short-time aging in the temperature range between 400 and 1000 °C on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel(LDSS) 2002 was investigated through the potentiostatic critical pitting temperature(CPT) tests and the Charpy impact tests. Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 °C concurrently. The CPT of LDSS 2002 specimen aged at 650 °C decreased by 28 °C, and the impact energy dropped from 69 to 29 J/cm~2 compared with the solution-annealed sample. Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr_2N and M_(23)C_6 along the ferrite–austenite grain boundaries.     

Information for Contributors

正The Transactions of Nonferrous Metals Society of China,founded in 1991 and sponsored by The Nonferrous Metals Society of China,is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology,including mineral processing,extraction metallurgy,metallic materials and heat treatments,metal working,physical metallurgy,powder metallurgy,with the emphasis