首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
成分是影响Sm(CoFeCuZr) z 性能的关键因素之一。本文概述了成分对高温永磁体Sm(CoFeCuZr) z 显微组织和磁性能影响的研究状况。并指出了掌握成分与显微组织和磁性能的关系 ,对制造高性能高温永磁体Sm(CoFeCuZr) z 的现实意义。  相似文献   

2.
通过粉末冶金法制备了不同z值(z=7.5~8.5)的Sm(CoFeCuZr)_z磁体。利用磁性能测量系统、X射线衍射分析、电子探针以及透射显微镜等对磁体的性能、组成相、析出相含量、微观结构及元素分布进行表征,通过分析解释了磁性能随z值变化的内在机理。结果表明:随z值增大,胞状结构尺寸增大,高饱和磁化强度的2:17R相增多导致剩磁Br升高;z值增大导致富Zr析出相增多,引起方形度H_k/H_(cj)下降;z值通过改变Cu元素在2:17R相界面位置的富集程度来改变矫顽力H_(cj)的大小,在一定范围内(z8.2)该位置Cu含量越高,矫顽力越大。  相似文献   

3.
简要介绍了新型高温永磁体Sm(Co ,Fe ,Cu ,Zr) z 的研究现状 ,总结了提高高温磁体的最高使用温度的方法 ,并对今后的研究方向作了评述。  相似文献   

4.
采用粉末冶金工艺制备了Sm(Co.Fe,Cu,Zr)z(6.5<z<8.5)烧结磁体,通过改变时效处理温度和时效时间等一系列处理方法对同一种成分和烧结工艺的磁体进行回火热处理,并对时效处理的磁体磁性能进行测定,研究发现热处理工艺对磁体的磁性能有较大的影响,剩磁Br在835℃时效处理8h左右达到最高,而矫顽力随着热处理时间和温度的增加是不断增大的.最后对这些影响磁性能的机理进行了讨论.  相似文献   

5.
综述了国内Sm2Fe17Nx粘结永磁体未能商品化的原因,以及其制备过程中磁性能的影响因素,简要指出了Sm2Fe17Nx今后的研发方向。  相似文献   

6.
本文研究了Sm(Co, Cu, Fe, Mn)_(7.8)永磁体铸造结晶组织及Cu偏析对矫顽力的影响。结果表明,不同冷却速度的铸造合金锭具有不同的结晶组织。在等轴晶组织中,晶内贫Cu,晶界上富集游离Cu,保存有一些Sm_2Co_(17-x)T_x六方结构高温相,造成矫顽力下降;而在细的柱状晶组织中,无严重的成分偏析。经烧结和固溶处理后的磁体,为位错胞状显微组织,胞壁间弥散着脱溶Cu和富Cu的SmCo_(5-x)T_x相,它们在反磁化过程中,可能对畴壁起着钉扎作用,因而具有高矫顽力。  相似文献   

7.
本文研究了Sm(Co, Cu, Fe, Mn)_(7.8)永磁体铸造结晶组织及Cu偏析对矫顽力的影响。结果表明,不同冷却速度的铸造合金锭具有不同的结晶组织。在等轴晶组织中,晶内贫Cu,晶界上富集游离Cu,保存有一些Sm_2Co_(17-x)T_x六方结构高温相,造成矫顽力下降;而在细的柱状晶组织中,无严重的成分偏析。经烧结和固溶处理后的磁体,为位错胞状显微组织,胞壁间弥散着脱溶Cu和富Cu的SmCo_(5-x)T_x相,它们在反磁化过程中,可能对畴壁起着钉扎作用,因而具有高矫顽力。  相似文献   

8.
以AZ31镁合金为基础,通过加入稀土元素Sm(钐)进行合金化,以获得室温和高温力学性能优良的耐热镁合金。采用光学显微镜、扫描电镜、X射线衍射仪、电子拉伸试验机等多种分析和测试手段,较为系统地研究了稀土元素Sm对AZ31镁合金显微组织及室温和高温力学性能的影响。结果表明,适量的稀土元素Sm的加入能够改善AZ31镁合金的显微组织,提高其力学性能。随着钐含量的增加,合金的强度和伸长率先升高后降低,且当w(Sm)=1.5%时,不论是在室温(20℃)还是在高温(150℃、175℃),合金的抗拉强度和伸长率取得最大值。在稀土元素Sm的加入量一定时,合金的抗拉强度随温度的升高而降低。  相似文献   

9.
综述了具有磁交换耦合作用的新型Sm-Co复合永磁体的研究进展.说明了硬磁相与软磁相间的磁交换耦合作用机理,以及交换耦合作用对复合永磁材料磁性能的影响.通过列举典型的Sm-Co永磁体及其磁性能,讨论了合金成分、添加元素和制备工艺对磁性材料显微结构和磁性能的影响,并且重点介绍了快淬速度对磁性能的影响.  相似文献   

10.
借助光学显微镜、扫描电镜、X射线衍射仪和DNS100电子万能试验机研究AM60合金中加入Sm后的显微组织和力学性能,并分析Sm对合金显微组织和力学性能的影响。结果表明,添加元素Sm可以细化镁合金的晶粒,改变β相的形态和大小,从连续或断续网状、长条状,变为卵石状或颗粒状均匀弥散分布在α-Mg基体上,显著改善合金的显微组织。Sm的加入可形成稳定性较高的颗粒状Al2Sm高温化合物相。随着Sm含量的增加,合金的抗拉伸强度和伸长率呈现先升后降的趋势,当Sm含量为1.0%(质量分数,下同)时抗拉伸强度和伸长率分别达到最大值210MPa和6.9%。室温下AM60合金的断口呈解理断裂,加入Sm变质后其断口形貌表现为准解理+局部韧性断裂特征。  相似文献   

11.
12.
13.
A synergetic approach to solution of problems of self-controlled synthesis of nanostructures and creation of self-organizing nanotechnologies is considered in connection with the superproblem of creation of materials with functional properties resembling those of biosystems. __________ Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 7, pp. 55 – 61, July, 2005.  相似文献   

14.
Conclusions To provide a high level of mechanical properties in wrought blanks of cast ÉP741NP and ÉP962 alloys it is necessary to form controlled structures. A necklace-type structure formed in homogenizing isostatic treatment, subsequent thermomechanical working including alternation of the operations of deformation in the (+)-area and recrystallization anneals, and final heat treatment is preferable. The temperature conditions of all stages of thermomechanical working are strictly controlled, especially the final operation of deformation and heating for hardening. To eliminate hardening cracks and distortions it is necessary to use molten salts at t=600°C as quenchants. The use of multiple production operations makes it possible to significantly reduce the structural inhomogeneity related to inhertance of the original dendritic structure. However, the structure of the final semifinished product is nevertheless characterized by a difference in occurrence of the processes of polygonization and recrystallization between the former dendritic cells and the interdendritic spaces in deformation and heat treatment.To obtain structurally homogeneous blanks for gas turbine engine parts it is necessary to use basically new methods of remelting such as vacuum double electrode remelting and electron beam remelting with an intermediate vessel.Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 12, pp. 25–29, December, 1991.  相似文献   

15.
C. Colinet 《Intermetallics》2003,11(11-12):1095
A large number of ab-initio calculations of energies of formation of intermetallic compounds have been performed in the last 15 years. The currently used methods are listed. The paper presents a review of the aluminium based compounds which have been studied. Comparisons of calculated and experimental enthalpies of formation are provided for aluminim-3d and-4d transition metal alloys at equiatomic composition. The modelling of the enthalpies of mixing of solid solutions based on a given lattice is described.  相似文献   

16.
17.
洋务派在洋务学堂的办学活动中,为了解决西学专业学科的教学困难,采用了聘请外籍教师的应急措施.他们以真才实学,合同制管理作为主导思想,并认为这种解决师资的途径只是权宜之计,并非久远.从客观上看,洋务派的教师聘任思想有深刻的历史影响.  相似文献   

18.
The importance of the self-diffusion of a metal during its oxidation by a gas is treated for the cases of nonstoichiometric oxides having either interstitial cation or cation vacancies. We have established a general relationship for the reaction rate when a mixed diffusion process occurs. From this relationship, we have shown that the pressure dependence can be different, according to whether the rate-determining process is the self-diffusion through the metal or through the product.  相似文献   

19.
刘兴  赵霞 《表面技术》2008,37(1):37-39
采用激光辐照对FeCrAlW电弧喷涂层的组织进行致密化处理,借助扫描电镜和X衍射对涂层的组织进行了分析.测试了涂层的显微硬度.结果表明:涂层组织致密度提高,孔隙率明显降低.随着激光扫描速度的增加,涂层的显微硬度降低.在较低的扫描速度下,涂层与基体之间形成互熔区,涂层与基体之间产生良好的冶金结合.  相似文献   

20.
论述了CAD技术中参数化设计的三种建模方法,重点介绍了基于特征的参数化建模原理。在此基础上,分析机械设计中的机构结构,归纳出其零件的几何特征构成。设计了机构CAD图形库,并提出了该图形库生成步骤和人机交互界面。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号