首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 52 毫秒
1.
严勇  郭力  张国华 《机床与液压》2012,40(5):27-31,63
在用热电偶进行磨削温度实验的基础上,分别运用解析法和有限元仿真法研究了金属材料超高速磨削的温度场,得出了其磨削温度场的分布;并分析了不同热源模型对温度场分布的影响.分析结果表明:随着Peclet数L值增大,磨削区热流分布从三角形变为均匀分布,且不同热源模型最高磨削温度相近,但出现的位置不同.  相似文献   

2.
针对阻碍宽台面单轴四点高速压力机实际应用的工作温升问题,研究了高速压力机热量产生机理,建立了热源分布模型,借助于ANSYS软件工具对温度场进行了数值仿真分析,揭示了温度分布与变化规律,在此基础上设计了高速压力机油冷冷却系统。数值仿真与实验研究结果均表明,在不采取任何散热或冷却措施时,高速压力机温度持续增高,达到热平衡的时间较长,热平衡点温度较高;采取强制油冷措施,可使高速压力机较快进入热平衡状态,并可将各运动部位工作温升控制在15℃之内,满足了实际应用要求。  相似文献   

3.
高固相率SiCP/AZ61复合材料触变成形的数值模拟   总被引:1,自引:0,他引:1  
采用等温热处理法制备SiCP/AZ61复合材料半固态坯料,在自制实验装置上进行触变成形实验.采用所建立的高固相率SiCP/AZ61复合材料本构模型,对触变成形过程进行了数值模拟,得到了不同成形温度下的应力、应变和温度场分布.结果表明,与成形温度为530℃相比,560℃时复合材料触变成形具有变形抗力小、应变与温度场分布均匀的特点.通过实验和模拟结果对比可知(成形温度为560℃),两者吻合较好,所获结果可指导高固相率镁基复合材料触变成形工艺实践.  相似文献   

4.
张增光  刘刚  焦清洋  康冲 《金属热处理》2020,45(11):192-196
采用SYSWELD软件对A-100钢复杂连接件进行了有限元建模,对其在无刚性约束条件下淬火过程中温度场和形变进行了模拟仿真,并对模拟结果进行了试验验证。温度场结果表明:冷却0.13 s时温度分布均匀,零件表面温度在820 ℃左右;冷却5~60 s时,零件表面的温度分布极为不均匀,零件头部型腔的棱角处温度较低,而位于底部的支臂与翼面连接处温度较高;而当冷却时间延长至160 s左右时,零件的整体温度已降至60 ℃以下。形变场结果表明:当冷却时间为0.5~10 s时,翼面远离加强筋部位产生较大淬火畸变,顶端棱角处畸变达3 mm;冷却到600 s时,最大畸变量减小至0.65 mm。根据畸变模拟结果设计了专用淬火工装,校形率达到70%左右。  相似文献   

5.
为克服传统加工方式的弊端,设计16 MN螺旋压力机上下加温模座并进行基于PLC的恒温控制系统的实验研究。进行上下模座的结构设计及强度校核,采用基于目标值滤波的二自由度PID控制算法实现了恒温模座闭环控制系统。实验结果表明:模座结构合理,强度满足要求;上下模座加热棒选用得当、分布合理,模座温度分布均匀;在2 h内,模座可由常温加热到350℃;上下模座温差小,控制精度高。  相似文献   

6.
为了对汽车用铝材分流模挤压过程的温度场分布进行分析,根据刚塑性有限元基本原理,利用数值模拟技术对其进行评估.分析了挤压速度及摩擦因子对坯料截面不同方向(平行及垂直挤压方向)的温度场分布的影响,选取特征点对焊合区域的温度场分布进行研究.对数值模拟结果进行分析可知,当坯料初始温度为450℃,摩擦因子为0.3时,挤压速度由1增至3mm·s-1时,温度最大值与最小值的差值在X方向上由7℃增至8℃、在Y方向上由9℃增加到10℃;通过对温度场的分析发现:具有良好散热条件的挤压筒壁附近的特征点温度出现一定程度的下降,而一些位于内部的特征点热损失很小,而且与坯料间具有不同程度的热交换,因此温度下降幅度小,在某些点上甚至出现了反常升高.  相似文献   

7.
《塑性工程学报》2013,(5):45-49
采用ProCAST软件,对高强钢板热冲压成形工艺冷却(淬火)过程进行数值模拟分析,计算了连续多个冲压工作循环下模具和坯料的温度场。结果表明,模具在连续多个冲压工作循环中,温度呈周期性的快速上升和快速下降的变化趋势,当每一个冲压工作循环结束时,模具的温度都保持在50℃左右。坯料在淬火过程中,其温度呈快速降低趋势,冲压结束时坯料的出模温度分布在75℃225℃上下,出模温度随冲压工作循环的进行而依次略有升高,并达到稳定。对模具和坯料进行试验测试,其温度值与数值模拟值吻合较好,说明该计算模型和方法对成形工艺设计有较好的预测评价作用。  相似文献   

8.
氮化硅陶瓷干湿磨削温度与表面质量研究   总被引:1,自引:0,他引:1  
为研究干湿磨两种条件下氮化硅陶瓷温度场特性,以及磨削力、温度场特性与表面质量三者间的关系。在理论分析的基础上运用ABAQUS有限元软件对其进行仿真,最后通过实验分析干湿磨条件下的温度场对其表面特性的影响。得出在干湿磨两种条件下的磨削力与磨削区温度场的关系以及磨削温度场的分布情况;并分析了温度场对其热裂纹的影响与温度和其表面特性的关系。得出磨削力是影响磨削区温度场变化的主要因素;随着磨削表面下深度的增加,湿磨下磨削温度的幅度变化要大于干磨,且磨削温度的幅度变化对其表面特性与裂纹的产生有所影响;干磨条件下的表面粗糙度与微观形貌要优于湿磨条件下。  相似文献   

9.
夏罗生 《焊接技术》2012,41(11):16-19
温度分布情况是影响搅拌摩擦焊焊缝性能的重要因素,利用Fluent软件,建立了搅拌摩擦焊三维温度场模型,并对铝合金厚板的温度场进行了数值仿真。结果显示:在焊缝上表面,沿焊缝中心向外延伸,温度场形状依次为"圆形"、"椭圆形",温度由低变高,再由高变低;在焊缝横截面,温度场为"倒金字塔"形状,上表面温度最高,由上至下,温度逐渐降低;轴肩的摩擦热是影响焊缝区温度分布的重要因素,其影响程度随深度的增加而逐渐减弱。仿真结果与试验结果基本吻合。  相似文献   

10.
目的设计一种以降低表面热辐射为主的疏导式热控结构,通过对疏导式热控结构的热性能进行仿真计算与试验,探讨其温度场分布影响因素。方法采用FLUENT软件,仿真分析了该热控结构在热源200℃时,隔热材料和通风条件对流场及温度场的影响。采用5 mm厚、导热系数为0.036 W/(m·K)的隔热材料和1 mm厚的纯铝板,制备了总厚度为100 mm的疏导式热控结构,测试在热源200、300、400℃时,距隔热层表面0、5、15、35、55、75、95 mm平面内和热控结构外表面的温度,并与仿真计算结果进行了对比。结果在不通风条件下,热源为200、300、400℃时,热控结构外表面的温度分别为48.1、66.8、87.9℃;在5 m/s通风条件下,热源为200、300、400℃时,热控结构外表面的温度分别为36.5、39.8、47.4℃。结论仿真计算获得的温度值与实测值一致,疏导空间内部受热量辐射的影响随高度的增大逐渐减小,适当采用气体对流机制能够显著降低疏导空间和热控结构外表面的温度。  相似文献   

11.
The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.  相似文献   

12.
Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.  相似文献   

13.
In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.  相似文献   

14.
After nearly two years' tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry (SRIF), located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.  相似文献   

15.
韩磊 《腐蚀与防护》2015,36(1):84-90,94
综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。  相似文献   

16.
正Harbin General Hydraulic Machinery Works Co.,Ltd.of Yilin Hydraulic Group is the most professional production base of large-scale metallurgy oil cylinder and oil machinery cylinder in the Northeast of China.The main products include metallurgy cylinder,swell-shrink cylinder,rotating injection device,lifting cylinder,main lifting jack,front lifting jack,engineering oil cyl-  相似文献   

17.
<正>Copyright Information For Authors As soon as an article is accepted for publication,authors will be requested to assign copyright of the article(or to grant exclusive publication and dissemination rights)to the publisher(respective the owner if other than Springer).This will ensure the widest possible protection and dissemination of information under copyright laws.More information about copyright regulations for this journal is available at  相似文献   

18.
《中国铸造》2014,(6):539-539
The ANKIROS/ANNOFER/TURKCAST shows held on Sept. 11-14, 2014, in Istanbul, Turkey, provided an ideal opportunity for the World Foundry Organization Executive Board to meet and discuss member benefits. Nine executive board members attended the meeting, including Dr. Lou Yanchun, Vice President of FICMES and President of Shenyang Research Institute of Foundry. During the board meeting, the WFO executives agreed to establish a special working group which is responsible for drafting a strategical plan for the WFO and submitting it for discussion at the next board meeting in 2015.  相似文献   

19.
《中国铸造》2014,(5):460-463
The 9th China International Diecasting Congress and the 1st International Symposium on Nonferrous Alloys and Special Casting Technologies (ISNASCT) were successfully held in Shanghai on July 19-22, 2014. Both events were jointly sponsored by Chinese Mechanical Engineering Society, Die Casting Commission of World Foundry Organization and Non-Ferrous Materials Commission of World Foundry Organization, and organized by the Foundry Institution of Chinese Mechanical Engineering Society (FICMES) and China Productivity Promotion Center of Foundry Industry.  相似文献   

20.
正Weihai HHH Mach.Elec.Group is the most technical company focusing on Power transmission and Hydra-controlling.HHH has the ability of developing and testing of complete sets of transmission system with relevant technical training.HHH provide efficient,excellent cost-effective power transmission system and intelligent electric fluid transmission and control system to OEM customers,who are  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号