Probabilistic production costing of diesel-wind energy conversionsystems

This paper describes the development of a general probabilistic model of a diesel-wind energy conversion system (DWECS) composed of several diesel units, several wind turbines (wind farm), and battery storage feeding a load. The model allows the simulation of a diesel system with a wind farm of different wind turbine types considering system stability, and outages due to hardware failure and primary energy fluctuations. It is based on a modification of the convolution method, which considers a given penetration level selected by the utility for stability consideration. The production costs of the diesel units are then deduced from the expected energy not supplied (EENS) using a unit de-convolution in reverse economic order. A methodology is also presented to determine the size of the battery storage based on the excess wind energy available during operation, or that disconnected for stability consideration, while accounting for the charging/discharging cycles     

储能系统协同常规机组调峰控制策略研究

大规模风电并网会引起电力系统调峰能力不足,造成火电机组频繁启停或弃风。文章利用电池储能充放电灵活、可补充常规机组调峰能力不足的特性,提出了AGC机组、NON-AGC机组与储能系统间的协调控制策略。该策略引入了改进调度时间级,实现储能与常规机组时间协调配合;以AGC机组与NON-AGC机组的协调机制为基础,建立了AGC机组向NON-AGC机组与电池储能的转移功率模型。根据前一时刻机组的输出功率,计算出机组的调节余量实现电池储能参与系统调峰。实际系统算例分析结果表明,所提控制策略的可行性和有效性。     

A combined probabilistic/time series model for wind diesel systems simulation

This article describes a new simulation model for wind/diesel systems. It involves a combined time series and statistical approach to estimate the fuel use of diesel generators. In addition to provision for modeling non-identical diesels, the model allows the inclusion of multiple, non-identical wind turbines whose output may or may not be correlated. Three diesel dispatching strategies are provided. One assumes no storage, and when storage is employed, either a peak shaving or cycle charge control option can be used. The storage module uses a flexible battery model specially designed for time series simulation codes. A key assumption for the main analytical model is that, within each time step, the load and wind power are assumed to be normally distributed. The mean net load is the mean load less the mean wind power and its variance is found from the variance of the load and the wind power. A loss of load probability is used to find the maximum and minimum anticipated values of the net load. In addition to summarizing the overall analytical model, this article presents the results of a number of simulations demonstrating the performance prediction (diesel fuel usage) capabilities of the model. For one of these cases (a no storage system), the results show excellent correlation between the model and actual data. Other cases summarized show that the use of the model greatly facilitates the integration of storage into the control scheme, and gives the fuel saving potential for several different wind/diesel system configurations.     

独立式风光互补发电系统中最大功率控制策略研究

独立风光互补发电系统从能量的角度来看可以分为3部分,即能量获取部分,能量存储部分以及能量消耗部分。主要介绍了能量获取所涉及的风力机最大功率运行和光伏电池最大功率跟踪这2个问题的控制策略,同时对能量存储部分所涉及的蓄电池充放电的控制策略进行了介绍,其中对充电策略的三阶段法做了比较详细的分析。最后对最大功率控制策略的研究方法作了系统的评述并对该领域今后的研究方向作了展望。     

风力发电系统输出功率随机波动的仿真分析

针对当前风力发电系统输出功率随机波动的问题,以永磁同步风力发电机(PMSG)与直流侧储能系统(钒氧化还原电池)整合的风力发电系统为基础,进行数字仿真建模,采用MATLAB/Simulink软件对固定负载,变化风速工况;固定风速,负荷瞬变工况;风速和负荷同时变化工况;进行了仿真试验和分析。结果表明,对于采用储能技术的风电场并网功率随机波动的平抑控制,可以利用蓄电池的充放电特性,在风速变化以及负荷瞬变时进行功率平衡的调节。     

Implementation of repowering optimization for an existing photovoltaic‐pumped hydro storage hybrid system: A case study in Sichuan,China

For a remote area or an isolated island, where the grid has not extended, a standalone hybrid energy system can provide cheap and adequate power for local users. However, with the development of society, the load demand will increase and the original system cannot completely meet the load demand. This situation occurs in Xiaojin, Sichuan, China. The existing photovoltaic‐pumped hydro storage (PV‐PHS) hybrid system in this area as the original system cannot completely meet the load requirements at present. The term “repowering” aims to maximize the reliability of power supply and the utilization of the PV‐PHS hybrid energy system that differs from traditional planning optimization to build all components. The repowering strategy is to integrate wind turbines (WTs) and battery into the original system. For the repowering system, a power management strategy is proposed to determine the operating modes of the PHS and battery. Three objectives, which are minimizing percentage of the demand not supplied, levelized cost of energy, and curtailment rate of renewable energy, are considered in the optimization model. Simulation is conducted by single‐objective, biobjective, and triobjective particle swarm optimization (PSO) techniques. For the single‐objective optimization, the comparison of PSO and genetic algorithm (GA) is made. For the double‐objective optimization, multiobjective PSO (MOPSO) is compared with weighted sum approach (WSA), and fuzzy satisfying method is utilized to find the win‐win solution. The results reveal that the repowering strategy can help to achieve maximum reliability of power supply after load demand increases significantly, and the battery plays an important role in such a hybrid system.     

Dynamic behavior of a stand-alone hybrid power generation system of wind turbine,microturbine, solar array and battery storage

This paper presents dynamic behavior and simulation results in a stand-alone hybrid power generation system of wind turbine, microturbine, solar array and battery storage. The hybrid system consists of a 195 kW wind turbine, an 85 kW solar array; a 230 kW microturbine and a 2.14 kAh lead acid battery pack optimized based on economic analysis using genetic algorithm (GA). At first, a developed Lyapunov model reference adaptive feedback linearization method accompanied by an indirect space vector control is applied for extraction of maximum energy from a variable speed wind power generation system. Then, a fuzzy logic controller is designed for the mentioned purpose and its performance is compared with the proposed adaptive controller. For meeting more load demands, the solar array is integrated with the wind turbine. In addition, the microturbine and the battery storage are combined with the wind and solar power generation system as a backup to satisfy the load demand under all conditions.A supervisory controller is designed in order to manage energy between the maximum energy captured from the wind turbine/solar arrays, and consumed energies of the load, dump load, battery state of charge (SOC), and generated energy by the microturbine. Dynamic modeling and simulation are accomplished using MATLAB Simulink? 7.2.     

Multiobjective optimal dispatch of microgrid based on analytic hierarchy process and quantum particle swarm optimization

Owing to the rapid development of microgrids (MGs) and growing applications of renewable energy resources, multiobjective optimal dispatch of MGs need to be studied in detail. In this study, a multiobjective optimal dispatch model is developed for a standalone MG composed of wind turbines, photovoltaics, diesel engine unit, load, and battery energy storage system. The economic cost, environmental concerns, and power supply consistency are expressed via subobjectives with varying priorities. Then, the analytic hierarchy process algorithm is employed to reasonably specify the weight coefficients of the subobjectives. The quantum particle swarm optimization algorithm is thereafter employed as a solution to achieve optimal dispatch of the MG. Finally, the validity of the proposed model and solution methodology are confirmed by case studies. This study provides reference for mathematical model of multiojective optimization of MG and can be widely used in current research field.     

Empowering the electric grid: Can SMES coupled to wind turbines improve grid stability?

The transition to a low carbon energy portfolio necessitates a reduction in the demand of fossil-fuel and an increase in renewable energy generation and penetration. Wind energy in particular is ubiquitous, yet the stochastic nature of wind energy hinders its wide-spread adoption into the electric grid. Numerous techniques (improved wind forecasting, improved wind turbine design and improved power electronics) have been proposed to increase the penetration of wind energy, yet only a few have addressed the challenges of wind intermittency, grid stability and flexibility simultaneously. The problem of excess wind energy results in wind curtailment and has plagued large scale wind integration. NREL's HOMER software is used to show that a strong negative correlation exists between the cycles to failure of a storage device and the excess wind energy on the system. A 1 MJ magnesium-diboride superconducting magnetic energy storage (SMES) system is designed to alleviate momentary interruptions (lasting from a few milli-seconds to a few minutes) in wind turbines. The simulation results establish the efficacy of SMES coupled with wind turbines improve output power quality and show that a 1 MJ SMES alleviated momentary interruptions for ∼50 s in 3 MW wind turbines. These studies suggest that SMES when coupled to wind turbines could be ideal storage devices that improve wind power quality and electric grid stability.     

An analysis for the need of a battery energy storage system in tracking wind power schedule output

电池储能系统(battery energy storage system,BESS)在风储联合应用中具有多种功能,利用电池储能系统提高风电并网调度运行能力是当前研究的热点之一.文章基于我国北方某风电场历史运行数据与预测数据,依据预测误差评价指标和风电场预报考核指标的综合评价方法对风电场预测数据进行分析研究,归纳了预测误差的概率分布特征;提出利用电池储能系统提高风电跟踪计划出力能力,统计并量化出电池储能系统用于跟踪计划出力场合的作用范围;通过仿真验证电池储能系统在风储联合系统中提高风电跟踪计划出力控制策略的有效性和可行性.     

Minimization and control of battery energy storage for wind power smoothing: Aggregated,distributed and semi-distributed storage

A battery energy storage system (BESS) is usually integrated with a wind farm to smooth out its intermittent power in order to make it more dispatchable. This paper focuses on the development of a scheme to minimize the capacity of BESS in a distributed configuration using model predictive control theory and wind power prediction. The purpose to minimize the BESS capacity is to reduce the overall cost of the system as the capacity of BESS is the main cost driver. A new semi-distributed BESS scheme is proposed and the strategy is analyzed as a way of improving the suppression of the fluctuations in the wind farm power output. The scheme is tested for similar and dissimilar wind power profiles, where the turbines are geographically located closer and further from each other, respectively. These two power profiles are assessed under a variety of hard system constraints for both the proposed and conventional BESS configurations. Based on the simulation results validated with real-world wind farm data, it has been observed that the proposed semi-distributed BESS scheme results in the improved performance as compared with conventional configurations such as aggregated and distributed storage.     

基于双模糊控制的独立微网能量优化策略

为使微网运行效益最大化,提出一种含风—储系统的独立微网的能量优化策略,该策略采用双层模糊控制方式,针对微网峰谷特性,根据日前启停机计划确定风电机组与需求侧管理负荷的投切状态,对实时调度则使用模糊控制得到风电机组、储能与负荷的功率值。对于微网瞬时功率波动,采用模糊理论,通过蓄电池—需求侧负荷混合系统平抑功率波动。实例应用结果表明,该独立微网能量优化策略有效。     

Inhibition of wind power fluctuations of battery energy storage system adaptive control strategy design

为了增加电池储能系统针对大规模风电并网对电网系统的友好性,降低风电功率波动对电网的不利影响,本文提出以电池荷电状态和风电功率为反馈量,改变平抑时间常数和电池储能系统充放电目标功率为目标的平抑风电功率波动的自适应控制策略。经仿真验证,上述策略能有效避免电池的荷电状态大幅波动,延长电池使用寿命,从而减小电池储能系统的安装容量,最大限度地发挥电池储能系统的作用。     

A comprehensive method for optimal power management and design of hybrid RES-based autonomous energy systems

The power management strategy (PMS) plays an important role in the optimum design and efficient utilization of hybrid energy systems. The power available from hybrid systems and the overall lifetime of system components are highly affected by PMS. This paper presents a novel method for the determination of the optimum PMS of hybrid energy systems including various generators and storage units. The PMS optimization is integrated with the sizing procedure of the hybrid system. The method is tested on a system with several widely used generators in off-grid systems, including wind turbines, PV panels, fuel cells, electrolyzers, hydrogen tanks, batteries, and diesel generators. The aim of the optimization problem is to simultaneously minimize the overall cost of the system, unmet load, and fuel emission considering the uncertainties associated with renewable energy sources (RES). These uncertainties are modeled by using various possible scenarios for wind speed and solar irradiation based on Weibull and Beta probability distribution functions (PDF), respectively. The differential evolution algorithm (DEA) accompanied with fuzzy technique is used to handle the mixed-integer nonlinear multi-objective optimization problem. The optimum solution, including design parameters of system components and the monthly PMS parameters adapting climatic changes during a year, are obtained. Considering operating limitations of system devices, the parameters characterize the priority and share of each storage component for serving the deficit energy or storing surplus energy both resulted from the mismatch of power between load and generation. In order to have efficient power exploitation from RES, the optimum monthly tilt angles of PV panels and the optimum tower height for wind turbines are calculated. Numerical results are compared with the results of optimal sizing assuming pre-defined PMS without using the proposed power management optimization method. The comparative results present the efficacy and capability of the proposed method for hybrid energy systems.     

Aggregate load-frequency control of a wind-hydro autonomous microgrid

This paper presents an aggregate load-frequency controller for an autonomous microgrid (MG) with wind and hydro renewable energy sources. A micro-hydro power plant with a synchronous generator (SG) and a wind power plant with an induction generator (IG) supply the MG. Both generators directly feed power into the grid without the use of additional power electronics interfaces, thus the solution becoming robust, reliable and cost-effective. An original electronic load controller (ELC) regulates the MG frequency by a centralized load-frequency control method, which is based on a combination of smart load (SL) and battery energy storage system (BESS). SL and BESS provides the active power balance for various events that such systems encounter in real situations, both in cases of energy excess production and energy shortage. Moreover, the proposed ELC includes an ancillary function to compensate the power unbalance produced by the uneven distribution of the single-phase loads on the MG phases, without the use of extra hardware components. A laboratory-scale prototype is used for experimentally assessment of the proposed solutions. The experimental results emphasize the effectiveness of the ELC while also showing its limitations.     

Technical and economic assessment of hybrid photovoltaic/wind system with battery storage in Corsica island

The sizing and techno-economical optimization of a stand-alone hybrid photovoltaic/wind system (HPWS) with battery storage is presented in this paper. The main objective of the present study is to find the optimum size of system, able to fulfill the energy requirements of a given load distribution, for three sites located at Corsica island and to analyze the impact of different parameters on the system size. The methodology used provides a useful and simple approach for sizing and analyzing an HPWS. In the proposed stand-alone system, a new concept such as the supply of wind power via a uninterruptible power supply (UPS) is introduced and therefore the energy produced by the wind generator can be sent directly to the load.     

An integrated control method for a wind farm to reduce frequency deviations in a small power system

Output power of wind turbine generator (WTG) is not constant and fluctuates due to wind speed changes. To reduce the adverse effects of the power system introducing WTGs, there are several published reports on output power control of WTGs detailing various researches based on pitch angle control, variable speed wind turbines, energy storage systems, and so on. In this context, this paper presents an integrated control method for a WF to reduce frequency deviations in a small power system. In this study, the WF achieves the frequency control with two control schemes: load estimation and short-term ahead wind speed prediction. For load estimation in the small power system, a minimal-order observer is used as disturbance observer. The estimated load is utilized to determine the output power command of the WF. To regulate the output power command of the WF according to wind speed changing, short-term ahead wind speed is predicted by using least-squares method. The predicted wind speed adjusts the output power command of the WF as a multiplying factor with fuzzy reasoning. By means of the proposed method, the WF can operate according to the wind and load conditions. In the WF system, each output power of the WTGs is controlled by regulating each pitch angle. For increasing acquisition power of the WF, a dispatch control method also is proposed. In the pitch angle control system of each WTG, generalized predictive control (GPC) is applied to enhance the control performance. Effectiveness of the proposed method is verified by the numerical simulations.     

Hybridized off-grid fuel cell/wind/solar PV /battery for energy generation in a small household: A multi-criteria perspective

In this paper, the robust capability of HOMER and Criteria-COPRAS is deployed to explore the prospect of selecting a renewable energy system. The energy system consisting of wind turbines, solar photovoltaic (PV), fuel cell (FC), electrolyzer, hydrogen storage, and battery energy storage is intended to power a residential load in Lagos Nigeria. Based on the economic metric, the results show that the optimal system is a PV-Battery whose total net present cost (TNPC) and initial investment cost are $9060 and $3,818, respectively. However, if the energy systems are ranked based on multiple criteria (economic, technical and environmental aspects), the most preferred of the feasible energy systems is a hybrid PV-FC-wind-battery (TNPC-$10,324, initial cost: $7670). The study results indicate that, for viability in the adoption of hydrogen energy storage as part of the hybrid energy system, the selection metric should be based on more than one criterion.     

风电场含退役动力电池的混合储能系统容量优化配置

针对退役电池在风电场平抑功率波动场景的应用,提出一种考虑退役电池时间尺度的混合储能系统容量配置方法。首先分析退役电池和新电池储能的优势,并介绍储能系统的成本构成;然后建立以全寿命周期经济性最优、考虑退役动力电池充放电时间尺度的混合储能容量配置模型,线性化后可调用求解器求解获取储能容量配置结果;最后用风电场实际数据进行分析,验证容量配置方法的有效性,并分析风电场不同储能配置时长政策要求、退役动力电池不同时间尺度以及不同控制策略下的混合储能容量配置结果。     

Review on combined wind power generation and energy storage systems

储能系统由于能够实现电能的时空平移,具有响应速度快,规模化等优点,是改善风电波动性,提高其并网能力的有效手段,构建风储联合发电系统成为目前研究重点.简单介绍了风电并网对电力系统的影响及不同类型电池储能技术的发展现状,给出了部分国内外风储联合发电系统的示范工程,并分析了平滑风电功率波动,跟踪计划出力曲线和削峰填谷3种主要运行方式,重点阐述了目前风储联合发电系统控制策略和储能容量配置研究现状,对进一步开展风储联合发电系统的研究进行了展望,指出经济性仍然是制约储能技术应用的关键问题之一,提高包含储能单元的风储联合发电系统的经济性是今后的研究重点.