Electrodeposition of nickel particles on a gas diffusion cathode for hydrogen production in a microbial electrolysis cell

Gas diffusion cathodes with electrodeposited nickel (Ni) particles have been developed and tested for hydrogen production in a continuous flow microbial electrolysis cell (MEC). A high catalytic activity of electrodeposited Ni particles in such a MEC was obtained without a proton exchange membrane, i.e. under direct cathode exposure to anodic liquid. Co-electrodeposition of Pt and Ni particles did not improve any further hydrogen production. The maximum hydrogen production rate was 5.4 L/L_R/day, corresponding to Ni loads between 0.2 and 0.4 mg cm⁻². Continuous MEC operation demonstrated stable hydrogen production for over one month. Owing to the fast hydrogen transport through the cathodic gas diffusion layer, the loss of hydrogen production to methanogenic activity was minimal, generally with less than 5% methane in the off-gas. Overall, gas diffusion cathodes with electrodeposited Ni particles demonstrated excellent stability for hydrogen production compared to expensive Pt cathodes.     

Process kinetics for the electrocatalytic hydrogen evolution reaction on carbon-based Ni/NiO nanocomposite in a single-chamber microbial electrolysis cell

To explore the process kinetics of hydrogen evolution reaction (HER) on carbon-based Ni/NiO nanocomposite in the microbial electrolysis cells (MECs), the performance was systematically studied by different time-course sampling of five parallel single-chamber MECs operated under identical operating conditions, which included the electrochemical performance of anodes and cathodes, and the mechanism and kinetics of HER. It was hypothesized that the decreased performance of the nickel cathodes was due to corrosion and Ni dissolution. These results provide valuable insights into the effects of long-term operation on MEC performance.     

Fabrication of NiO/Ta2O5 composite photocatalyst for hydrogen production under visible light

A series of novel composite photocatalysts, NiO/Ta₂O₅, were synthesized by the solid‐state reaction and successfully characterized by X‐ray diffraction, Transmission electron microscopy, diffused reflectance ultraviolet and visible (DRUV‐vis) spectroscopy, Photoluminescence and X‐ray photoelectron spectroscopy. Powder X‐ray diffraction (PXRD) pattern indicated the formation of composite material. The red shift in the absorption edges of the newly prepared composite photocatalysts were well observed from the DRUV‐vis spectra. The composite photocatalyst prepared at metal ratio (1:3) showed highest result toward hydrogen production under ultraviolet and visible light irradiation in the presence of methanol as a sacrificial agent. Copyright © 2011 John Wiley & Sons, Ltd.     

Hairy sphere-like Ni9S8/CuS/Cu2O composites grown on nickel foam as bifunctional electrocatalysts for hydrogen evolution and urea electrooxidation

The urea solution electrolysis has become more attractive than water splitting, because it not only produces clean H₂ via the cathodic hydrogen evolution reaction (HER) with lower cell voltage, but also treats sewage containing urea through anodic urea oxidation reaction (UOR). However, lack of efficient electrocatalysts for HER and UOR has limited its development. Herein, hairy sphere -like Ni₉S₈/CuS/Cu₂O composites were synthesized on nickel foam (NF) in situ by a two-step hydrothermal method. The Ni₉S₈/CuS/Cu₂O/NF exhibited good electrocatalytic activity for both HER (?0.146 V vs. RHE to achieve 10 mA cm^?2) and UOR (1.357 V vs. RHE to achieve 10 mA cm^?2). Based on the bifunctional properties of Ni₉S₈/CuS/Cu₂O/NF, a dual-electrode urea solution electrolytic cell was constructed, which only needed a low voltage of 1.47 V to reach a current density of 10 mA cm^?2, and displayed a good stability during a 20-h test. In addition, the reason for the good catalytic activity of Ni₉S₈/CuS/Cu₂O/NF was analyzed and the UOR mechanism was discussed in detail. Our research shows that Ni₉S₈/CuS/Cu₂O/NF is a very promising low-cost dual-function electrocatalyst, which can be used for high-efficiency electrolysis of urea solution to produce hydrogen and treat wastewater.     

The promoting effect of Fe on Ni/GDC for the Solid Oxide H2O electrolysis

The study deals with the modification of commercial Ni/GDC powder with iron and its use as fuel functional electrode for Solid Oxide H₂O electrolysis. The Fe-NiO/GDC samples were prepared with the Deposition-Precipitation method and characterized, in their oxidized and reduced form, by using BET, HR-TEM, SAED, XRD, XPS and TG analysis in the presence of H₂O. The electrochemical investigation deals with the comparison of single SOECs at 900°C, under various pH₂O/pH₂ ratios. In the oxidized powders iron was detected, both in the bulk and on the surface, in the form of crystallized Fe₂O₃ species, which during H₂-reduction interacted with NiO towards the formation of a Ni-Fe alloy. The latter promoted the electrochemical performance of the Fe-Ni/GDC electrodes, where there are indications of strong dependence on the Fe wt% content. Specifically, the performance of the cell with 0.5 wt% Fe-Ni/GDC was threefold higher than that with Ni/GDC. On the other hand, the cell with 2 wt% Fe-Ni/GDC was worse, implying that the promoting effect of Fe lies on quite low wt% content. Finally, the examined Fe-doped electrodes exhibited increase of polarization in high pH₂O. This is primarily ascribed to the fact that Fe-Ni/GDC electrodes seem more susceptible to H₂O oxidation. Overall, Fe is considered as a promising Ni/GDC dopant, capable to substitute noble metals like Au, but further investigation is required for the elucidation of key preparation and performance parameters.     

Development and application of vanadium oxide/polyaniline composite as a novel cathode catalyst in microbial fuel cell

Polyaniline (Pani), vanadium oxide (V₂O₅), and Pani/V₂O₅ nanocomposite were fabricated and applied as a cathode catalyst in Microbial Fuel Cell (MFC) as an alternative to Pt (Platinum), which is a commonly used expensive cathode catalyst. The cathode catalysts were characterized using Cyclic Voltammetry and Linear Sweep Voltammetry to determine their oxygen reduction activity; furthermore, their structures were observed by X‐ray Diffraction, X‐ray Photoelectron Spectroscopy, Brunauer–Emmett–Teller, and Field‐Emission Scanning Electron Microscopy. The results showed that Pani/V₂O₅ produced a power density of 79.26 mW/m², which is higher than V₂O₅ by 65.31 mW/m² and Pani by 42.4 mW/m². Furthermore, the Coulombic Efficiency of the system using Pani/V₂O₅ (16%) was higher than V₂O₅ and Pani by 9.2 and 5.5%, respectively. Pani–V₂O₅ also produced approximately 10% more power than Pt, the best and most common cathode catalyst. It declares that Pani–V₂O₅ can be a suitable alternative for application in a MFC system. Copyright © 2013 John Wiley & Sons, Ltd.     

Oxygen-releasing step of ZnFe2O4/(ZnO + Fe3O4)-system in air using concentrated solar energy for solar hydrogen production

The oxygen-releasing step of the ZnFe₂O₄/(ZnO + Fe₃O₄)-system for solar hydrogen production with two-step water splitting using concentrated solar energy was studied under the air-flow condition by irradiation with concentrated Xe lamp beams from a solar simulator. The spinel-type compound of ZnFe₂O₄ (Zn-ferrite) releases O₂ gas under the air-flow condition at 1800 K and then decomposes into Fe₃O₄ () and ZnO with a nearly 100% yield (ZnFe₂O₄ = ZnO + 2/3Fe₃O₄ + 1/6O₂). The ZnO was deposited as the thin layer on the surface of the reaction cell wall. A thermodynamic study showed that the ZnO was produced by the reaction between the O₂ gas in the air and the metal Zn vapor generated from ZnFe₂O₄. With the combined process of the present study on the O₂-releasing step and the previous one on the H₂ generation step (ZnO + 2/3Fe₃O₄ + 1/3H₂O = ZnFe₂O₄ + 1/3H₂) for the ZnFe₂O₄/(ZnO + Fe₃O₄)-system, solar H₂ production was demonstrated by one cycle of the ZnFe₂O₄/(ZnO + Fe₃O₄)-system, where the O₂-releasing step had been carried out in air at 1800 K and the H₂ generation step at 1100 K.     

Effect of anodization voltage on performance of TiO2 nanotube arrays for hydrogen generation in a two-compartment photoelectrochemical cell

Highly ordered TiO₂ nanotube arrays were prepared by anodic oxidation of Ti foil under different anodization voltages in ethylene glycol electrolyte. The morphology and photoelectrochemical performance of the TiO₂ nanotubes (NTs) samples were characterized by FESEM and electrochemical working station. Hydrogen production was measured by splitting water in the two-compartment photoelectrochemical (PEC) cell without any external applied voltage or sacrificial agent. The results indicated that anodization voltage significantly affects morphology structures, photoelectrochemical properties and hydrogen production of TiO₂ NTs. The pore diameter and layer thickness of TiO₂ samples increased linearly with the anodization voltage, which led to the enhancement of active surface area. Accordingly, the photocurrent response, photoconversion efficiency and hydrogen production of TiO₂ nanotubes were also linearly correlated with the anodization voltage.