An experimental study of the effect of a homogeneous combustion catalyst on fuel consumption and smoke emission in a diesel engine

This paper presents the results of an experimental investigation into the influence of a ferrous picrate based homogeneous combustion catalyst on fuel consumption and smoke emission of a laboratory diesel engine. The catalyst used in this study was supplied by Fuel Technology Pty. Ltd. The fuel consumption and smoke emission were measured as a function of engine load, speed and catalyst dosing ratio. The brake specific fuel consumption and smoke emission decreased as the dosing ratio of the catalyst doped in the diesel fuel increased. At the catalyst dosing ratio of 1:3200, the brake specific fuel consumption was reduced by from 2.1% to 2.7% and the smoke emission was reduced by from 6.7% to 26.2% at the full engine load at speeds from 2600 rpm to 3400 rpm. The results also indicated that the potential of the fuel saving seems to be greater when the engine was run under light load.     

Combined impact of varying biogas mass flow rate and rice bran methyl esters blended with diesel on a dual-fuel engine

ABSTRACT

For fetching day-to-day energy needs, current energy requirement majorly depends on fossil fuels. But ambiguous matter like abating petroleum products and expanding air pollution has enforced the experts to strive for another fuel which can be used as an alternative or reduce the applications of fossil fuels. Considering the issues, the main objective of the present study is to find the feasibility by using blends of rice bran oil biodiesel and diesel which are used as pilot fuels by blending 10% and 20% biodiesel in fossil diesel and biogas, introduced as gaseous fuel by varying its mass flow rate in a dual-fuel engine mode. An experimentation study was carried out to find the performance and emission parameters of the engine relative to pure diesel. The results were very much similar to the majority of researchers who used biodiesel and gaseous fuels in a dual-fuel engine. Brake specific fuel consumption (BSFC) of the engine was noticed to have increased, while brake thermal efficiency was on the lower side in dual fuel mode in comparison with regular diesel. In relation with conventional diesel, it was noticed that combined effect of rice bran methyl esters and varying mass flow rate of biogas showed a decrement in NO _x and smoke emissions, whereas HC and CO exhalations were on higher side when biogas and biodiesel were utilized collectively in dual-fuel engine. Hence, it was concluded that combination of blends of biodiesel and diesel and introduction of biogas in the engine can be a promising combination which can be used as a substitute fuel for addressing future energy needs.     

Experimental investigation on diesel engine with diestrol-water micro emulsions

Experiments were conducted on a single cylinder direct injection diesel engine using diesel, biodiesel and biodiesel-diesel-ethanol (diestrol) water micro emulsion fuels to investigate the performance, emission and combustion characteristics of the engine under different load conditions at a constant speed of 1500 rpm. The results indicated that biodiesel and micro emulsion fuels had a higher brake specific fuel consumption (BSFC) than that of diesel. A slight improvement in the brake specific energy consumption (BSEC) was observed for micro emulsion fuels. The brake thermal efficiency of biodiesel and micro emulsion fuels were comparable to that of diesel. The emission characteristics like carbon monoxide (CO), carbon dioxide (CO₂), unburnt hydrocarbon (UHC), nitric oxide (NO) and smoke emissions for biodiesel and micro emulsion fuels were lower than diesel fuel at all load conditions. The cylinder gas pressure of micro emulsion fuels was lower than diesel at low loads but it became almost identical to diesel at medium and full load conditions. The heat release rate for micro emulsion fuels was higher than biodiesel and diesel fuels for all loads. Biodiesel showed shorter ignition delay for the entire load range and the longer ignition delay observed for micro emulsion fuels.     

The effects of turbocharger on the performance and exhaust emissions of a diesel engine fuelled with biodiesel

This paper investigates the effects of turbocharger on the performance of a diesel engine using diesel fuel and biodiesel in terms of brake power, torque, brake specific consumption and thermal efficiency, as well as CO and NO_x emissions. For this aim, a naturally aspirated four-stroke direct injection diesel engine was tested with diesel fuel and neat biodiesel, which is rapeseed oil methyl ester, at full load conditions at the speeds between 1200 and 2400 rpm with intervals of 200 rpm. Then, a turbocharger system was installed on the engine and the tests were repeated for both fuel cases. The evaluation of experimental data showed that the brake thermal efficiency of biodiesel was slightly higher than that of diesel fuel in both naturally aspirated and turbocharged conditions, while biodiesel yielded slightly lower brake power and torque along with higher fuel consumption values. It was also observed that emissions of CO in the operations with biodiesel were lower than those in the operations with diesel fuel, whereas NO_x emission in biodiesel operation was higher. This study reveals that the use of biodiesel improves the performance parameters and decreases CO emissions of the turbocharged engine compared to diesel fuel.     

Promotion of bio oil,H2 gas from the pyrolysis of rice husk assisted with nano silver catalyst and utilization of bio oil blend in CI engine

This paper reports on the pyrolytic distillation of rice husk with catalyst and its influence on both condensable and non-condensable volatiles. The catalyst used for pyrolysis was nano sized silver particles obtained through chemical reduction method. The structural features of the nano silver particles were explored through X-ray diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM) with Energy-dispersive-X-ray spectroscope (EDX), and the size of the nano particles was confirmed as 90 nm. After intimately mixing the rice husk (30 g) with the catalyst, the pyrolysis at various temperatures (400 °C, 450 °C, 500 °C, 550 °C) was performed. The products obtained during catalytic pyrolysis like gaseous fuel, bio oil, and bio char were separately collected and characterized through Gas Chromatography-Mass Spectrometer (GC-MS) and Inductively Coupled Plasma – Optical Emission Spectrometer (ICP-OES). About 50% of the solid biomass was converted into more useful liquid and gaseous fuel. It was noticed that during catalytic pyrolysis, the quantity of H₂ obtained was more (19.12%) in contrast to thermal pyrolysis and could be attributable to the influence of silver nano particles towards the enhancement in hydrogen gas production. The liquid hydrocarbon obtained during the catalytic distillation was blended with diesel in the ratio 20:80 in the compression ignition (CI) engine. The quality of the blended bio oil was assessed from brake thermal efficiency (BTE), brake specific fuel consumption (BSFC) and emission of nitrogen oxides (NO_X), carbon monoxide (CO) and unburnt hydrocarbon (UHC). At full load, the diesel fuel emitted 1780 ppm of NO_x while the diesel blended with bio oil emitted only 1510 ppm which was 15.17% less than the diesel oil which proved its eco-friendly nature. In future, the bio oil obtained from catalytic pyrolysis can be used as a blend for diesel oil, since it reduces NO_x emission and replaces 20% of diesel oil.     

A modified diesel engine for natural gas operation: Performance and emission tests

A diesel engine was modified for natural gas operation to optimize performance using gaseous fuel. A variation of combustion ratios (CR) including 9.0:1, 9.5:1, 10.0:1 and 10.5:1 was utilized to evaluate engine performance and emissions from the same engine over the engine speeds between 1000 and 4000 rpm. Tested engine performance parameters include brake torque, brake power, specific fuel consumption (SFC) and brake thermal efficiency. Emissions tests recorded total hydrocarbon (THC), nitrogen oxides (NO_x) and carbon monoxide (CO). The results showed that a CR of 9.5:1 had the highest thermal efficiency and the lowest SFC while a CR of 10:1 showed a high torque at low speed. THC emissions were directly proportional to the CR. NO_x emissions increased with increasing CR and then declined after a CR of 10:1.     

Performance of jatropha oil blends in a diesel engine

Results are presented on tests on a single-cylinder direct-injection engine operating on diesel fuel, jatropha oil, and blends of diesel and jatropha oil in proportions of 97.4%/2.6%; 80%/20%; and 50%/50% by volume. The results covered a range of operating loads on the engine. Values are given for the chemical and physical properties of the fuels, brake specific fuel consumption, brake power, brake thermal efficiency, engine torque, and the concentrations of carbon monoxide, carbon dioxide and oxygen in the exhaust gases. Carbon dioxide emissions were similar for all fuels, the 97.4% diesel/2.6% jatropha fuel blend was observed to be the lower net contributor to the atmospheric level. The trend of carbon monoxide emissions was similar for the fuels but diesel fuel showed slightly lower emissions to the atmosphere. The test showed that jatropha oil could be conveniently used as a diesel substitute in a diesel engine. The test further showed increases in brake thermal efficiency, brake power and reduction of specific fuel consumption for jatropha oil and its blends with diesel generally, but the most significant conclusion from the study is that the 97.4% diesel/2.6% jatropha fuel blend produced maximum values of the brake power and brake thermal efficiency as well as minimum values of the specific fuel consumption. The 97.4%/2.6% fuel blend yielded the highest cetane number and even better engine performance than the diesel fuel suggesting that jatropha oil can be used as an ignition-accelerator additive for diesel fuel.     

Performance evaluation of a constant speed IC engine on CNG,methane enriched biogas and biogas

This paper presents the performance results of a 5.9 kW stationary diesel engine which was converted into spark ignition mode and run on compressed natural gas (CNG), methane enriched biogas (Bio-CNG) and biogas produced from biomethanation of jatropha and pongamia oil seed cakes. The performance of the engine with 12.65 compression ratio was evaluated at 30°, 35° and 40° ignition advance of TDC. The maximum brake power produced by the engine was found at ignition advance of 35° TDC for all the tested fuels. In comparison to diesel as original fuel, the power deteriorations of the engine was observed to be 31.8%, 35.6% and 46.3% on compressed natural gas, methane enriched biogas and raw biogas, respectively, due to its conversion from CI to SI mode. The methane enriched biogas showed almost similar engine performance as compared to compressed natural gas in terms of brake power output, specific gas consumption and thermal efficiency.     

Effect on performance and emissions of a dual fuel diesel engine using hydrogen and producer gas as secondary fuels

Energy is an essential prerequisite for economical and social growth of any country. Skyrocketing of petroleum fuel cost s in present day has led to growing interest in alternative fuels like CNG, LPG, Producer gas, Biogas in order to provide suitable substitute to diesel for a compression ignition engine. This paper discusses some experimental investigations on dual fuel operation of a 4 cylinder (turbocharged and intercooled) 62.5 kW gen-set diesel engine with hydrogen, producer gas (PG) and mixture of producer gas and hydrogen as secondary fuels. Results on brake thermal efficiency and emissions, namely, un-burnt hydrocarbon (HC), carbon monoxide (CO), and NO_x are presented here. The paper also contains vital information relating to the performances of an engine at a wide range of load conditions with different gaseous fuel substitutions. When only hydrogen is used as secondary fuel, maximum increase in the brake thermal efficiency is 7% which is obtained with 20% of secondary fuel. When only producer gas is used as secondary fuel, maximum decrease in the brake thermal efficiency of 8% is obtained with 30% of secondary fuel. Compared to the neat diesel operation, proportion of un-burnt HC and CO increases, while, emission of NO_x reduces in all Cases. On the other hand, when 40% of mixture of producer gas and hydrogen is used (in the ratio (60:40) as secondary fuel, brake thermal efficiency reduces marginally by 3%. Further, shortcoming of low efficiency at lower load condition in a dual fuel operation is removed when a mixture of hydrogen and producer gas is used as the secondary fuel at higher than 13% load condition. Based on the performance studied, a mixture of producer gas and hydrogen in the proportion of 60:40 may be used as a supplementary fuel for diesel conservation.     

Hydrogen impacts on performance and CO2 emissions from a diesel power generator

This work investigates the performance and carbon dioxide (CO₂) emissions from a stationary diesel engine fueled with diesel oil (B5) and hydrogen (H₂). The performance parameters investigated were specific fuel consumption, effective engine efficiency and volumetric efficiency. The engine was operated varying the nominal load from 0 kW to 40 kW, with diesel oil being directly injected in the combustion chamber. Hydrogen was injected in the intake manifold, substituting diesel oil in concentrations of 5%, 10%, 15% and 20% on energy basis, keeping the original settings of diesel oil injection. The results show that partial substitution of diesel oil by hydrogen at the test conditions does not affect significantly specific fuel consumption and effective engine efficiency, and decreases the volumetric efficiency by up to 6%. On the other hand the use of hydrogen reduced CO₂ emissions by up to 12%, indicating that it can be applied to engines to reduce global warming effects.     

Evaluating combustion,performance and emission characteristics of diesel engine using karanja oil methyl ester biodiesel blends enriched with HHO gas

With a specific end goal to take care of the worldwide demand for energy, a broad research is done to create alternative and cost effective fuel. The fundamental goal of this examination is to investigate the combustion, performance and emission characteristics of diesel engine using biodiesel blends enriched with HHO gas. The biodiesel blends are gotten by blending KOME obtained from transesterification of karanja oil in various proportions with neat diesel. The HHO gas is produced by the electrolysis of water in the presence of sodium bicarbonate electrolyte. The constant flow of HHO gas accompanied with biodiesel guarantees lessened brake specific fuel consumption by 2.41% at no load and 17.53% at full load with increased the brake thermal efficiency by 2.61% at no load and 21.67% at full load contrasted with neat diesel operation. Noteworthy decline in unburned hydrocarbon, carbon monoxide, carbon-dioxide emissions and particulate matter with the exception of NO_x discharge is encountered. The addition of EGR controls this hike in NO_x with a slight decline in the performance characteristics. It is clear that the addition of HHO gas with biodiesel blends along with EGR in the test engine improved the overall characterization of engine.     

Performance and emission study of preheated Jatropha oil on medium capacity diesel engine

Diesel engines have proved its utility in transport, agriculture and power sector. Environmental norms and scared fossil fuel have attracted the attention to switch the energy demand to alternative energy source. Oil derived from Jatropha curcas plant has been considered as a sustainable substitute to diesel fuel. However, use of straight vegetable oil has encountered problem due to its high viscosity. The aim of present work is to reduce the viscosity of oil by heating from exhaust gases before fed to the engine, the study of effects of FIT (fuel inlet temperature) on engine performance and emissions using a dual fuel engine test rig with an appropriately designed shell and tube heat exchanger (with exhaust bypass arrangement). Heat exchanger was operated in such a way that it could give desired FIT. Results show that BTE (brake thermal efficiency) of engine was lower and BSEC (brake specific energy consumption) was higher when the engine was fueled with Jatropha oil as compared to diesel fuel. Increase in fuel inlet temperature resulted in increase of BTE and reduction in BSEC. Emissions of NO_x from Jatropha oil during the experimental range were lower than diesel fuel and it increases with increase in FIT. CO (carbon monoxide), HC (hydrocarbon), CO₂ (carbon dioxide) emissions from Jatropha oil were found higher than diesel fuel. However, with increase in FIT, a downward trend was observed. Thus, by using heat exchanger preheated Jatropha oil can be a good substitute fuel for diesel engine in the near future. Optimal fuel inlet temperature was found to be 80 °C considering the BTE, BSEC and gaseous emissions.     

Effect of hydrogen and LPG addition on the efficiency and emissions of a dual fuel diesel engine

This paper presents some experimental investigations on dual fuel operation of a 4 cylinder (turbocharged and intercooled) 62.5 kW gen-set diesel engine with hydrogen, liquefied petroleum gas (LPG) and mixture of LPG and hydrogen as secondary fuels. Results on brake thermal efficiency and emissions, namely, un-burnt hydrocarbon (HC), carbon monoxide (CO), NO_x and smoke are presented here. The paper also includes vital information regarding performances of the engine at a wide range of load conditions with different gaseous fuel substitutions. When only hydrogen is used as secondary fuel, maximum enhancement in the brake thermal efficiency is 17% which is obtained with 30% of secondary fuel. When only LPG is used as secondary fuel, maximum enhancement in the brake thermal efficiency (of 6%) is obtained with 40% of secondary fuel. Compared to the pure diesel operation, proportion of un-burnt HC and CO increases, while, emission of NO_x and smoke reduces in both cases. On the other hand, when 40% of mixture of LPG and hydrogen is used (in the ratio 70:30) as secondary fuel, brake thermal efficiency enhances by 27% and HC emission reduces by 68%. Further, shortcoming of low efficiency at lower load condition in a dual fuel operation is removed when a mixture of hydrogen and LPG is used as the secondary fuel at higher than 10% load condition.     

Performance and emission analysis of compression ignition engine using biodiesels from Acid oil,Mahua oil,and Castor oil

Research on and use of biodiesels for engines is growing continuously in the present era. Compression ignition (CI) engine performance for biodiesels of blends B20 from Acid oil, Mahua oil, and Castor oil is experimentally investigated. The engine performance analysis in the form of brake‐specific fuel consumption, brake‐specific energy consumption, brake thermal efficiency (BTE), exhaust gas temperature (EGT), and air fuel ratio are compared with diesel as base fuel. Emission characteristics like CO, CO₂, NOx, and opacity are comparatively studied in detail for the considered biodiesels. The entire study is compared with the performance of engine when pure diesel is chosen as fuel. From the complete analysis it was observed that the BTE was higher for Acid oil and Mahua oil among the biodiesels used. And regarding CO emissions, Mahua oil showed lower effect than other biodiesels. Upto 6% increase in EGT of Mahua oil was obtained at no load and for other loads the percent reduced. For all the biodiesels the % enhancement in Co, CO₂, and NOx was more than 60% at highest load compared with diesel.     

6BTA 5.9 G2-1 Cummins engine performance and emission tests using methyl ester mahua (Madhuca indica) oil/diesel blends

Neat mahua oil poses some problems when subjected to prolonged usage in CI engine. The transesterification of mahua oil can reduce these problems. The use of biodiesel fuel as substitute for conventional petroleum fuel in heavy-duty diesel engine is receiving an increasing amount of attention. This interest is based on the properties of bio-diesel including the fact that it is produced from a renewable resource, its biodegradability and potential to exhaust emissions. A Cummins 6BTA 5.9 G2- 1, 158 HP rated power, turbocharged, DI, water cooled diesel engine was run on diesel, methyl ester of mahua oil and its blends at constant speed of 1500 rpm under variable load conditions. The volumetric blending ratios of biodiesel with conventional diesel fuel were set at 0, 20, 40, 60, and 100. Engine performance (brake specific fuel consumption, brake specific energy consumption, thermal efficiency and exhaust gas temperature) and emissions (CO, HC and NOx) were measured to evaluate and compute the behavior of the diesel engine running on biodiesel. The results indicate that with the increase of biodiesel in the blends CO, HC reduces significantly, fuel consumption and NOx emission of biodiesel increases slightly compared with diesel. Brake specific energy consumption decreases and thermal efficiency of engine slightly increases when operating on 20% biodiesel than that operating on diesel.     

Comparison between blended mode and fumigation mode on combustion,performance and emissions of a diesel engine fueled with ternary fuel (diesel-biodiesel-ethanol) based on engine speed

According to the literature, there is in lack of a comprehensive study to compare the combustion, performance and emissions of a diesel engine using diesel, biodiesel and ethanol fuels (DBE) in the blended mode and fumigation mode under various engine speeds. This study was conducted to fill this knowledge gap by comparing the effect of blended, fumigation and combined fumigation + blended (F + B) modes on the combustion, performance and emissions of a diesel engine under a constant engine load (50% of full torque) with five engine speeds ranging from 1400 rpm to 2200 rpm. A constant overall fuel composition of 80% diesel, 5% biodiesel and 15% ethanol, by volume % (D80B5E15), was utilized to provide the same fuel for comparing the three fueling modes.According to the average results of five engine speeds, the blended mode has higher peak heat release rate (HRR), ignition delay (ID), brake thermal efficiency (BTE), brake specific nitrogen monoxide (BSNO) and brake specific nitrogen oxides (BSNO_X), but lower duration of combustion (DOC), brake specific fuel consumption (BSFC), brake specific carbon dioxide (BSCO₂), brake specific carbon monoxide (BSCO), brake specific hydrocarbon (BSHC), brake specific nitrogen dioxide (BSNO₂), brake specific particulate matter (BSPM), total number concentration (TNC) and geometric mean diameter (GMD), and similar peak in-cylinder pressure compared to the fumigation mode. In addition, for almost all the parameters, results obtained in the F + B mode are in between those of the blended and fumigation modes. In regard to the effect of engine speed, the results reveal that the increase in engine speed causes reduction in peak in-cylinder pressure, BTE, BSHC, BSNO_X, BSNO and BSNO₂, but increase in peak HRR, ID, DOC, BSFC, BSCO₂, BSPM and TNC, and similar BSCO and GMD for almost all the tested fueling modes. It can be inferred that the blended mode is the suitable fueling mode, compared with the fumigation mode, under the operating conditions investigated in this study.     

Experimental investigation on biogas enrichment with hydrogen for improving the combustion in diesel engine operating under dual fuel mode

Biogas valorization as fuel for internal combustion engines is one of the alternative fuels, which could be an interesting way to cope the fossil fuel depletion and the current environmental degradation. In this circumstance, an experimental investigation is achieved on a single cylinder DI diesel engine running under dual fuel mode with a focus on the improvement of biogas/diesel fuel combustion by hydrogen enrichment. In the present investigation, the mixture of biogas, containing 70% CH₄ and 30% CO₂, is blended with the desired amount of H₂ (up to 10, 15 and 20% by volume) by using MTI 200 analytical instrument gas chromatograph, which flow thereafter towards the engine intake manifold and mix with the intake air. Depending on engine load conditions, the volumetric composition of the inducted gaseous fraction is 20–50% biogas, 2–10% H₂ and 45–78% air. Near the end of the compression stroke, a small amount of diesel pilot fuel is injected to initiate the combustion of the gas–air mixture. Firstly, the engine was tested on conventional diesel mode (baseline case) and then under dual fuel mode using the biogas. Consequently, hydrogen has partially enriched the biogas. Combustion characteristics, performance parameters and pollutant emissions were investigated in-depth and compared. The results have shown that biogas enriched with 20% H₂ leads to 20% decrease of methane content in the overall exhaust emissions, associated with an improvement in engine performance. The emission levels of unburned hydrocarbon (UHC) and carbon monoxide (CO) are decreased up to 25% and 30% respectively. When the equivalence ratio is increased, a supplement decrease in UHC and CO emissions is achieved up to 28% and 30% respectively when loading the engine at 60%.     

A study on the effect of hydrogen enriched intake air on the characteristics of a diesel engine fueled with ethanol blended diesel

This work aims to replace conventional diesel fuel with low and no carbon fuels like ethanol and hydrogen to reduce the harmful emission that causes environmental degradation. Pursuant to this objective, this study investigated the performance, combustion, and emission characteristics of the diesel engine operated on dual fuel mode by ethanol-diesel blends with H₂ enriched intake air at different engine loads with a constant engine speed of 1500 rpm. The results were compared to sole diesel operation with and without H₂ enrichment. The ethanol/diesel was blended in v/v ratios of 5, 10, and 15% and tested in a diesel engine along with a 9 lpm H₂ flow rate at the intake manifold. The results revealed that 10% ethanol with 9 lpm H₂ combination gives the maximum brake thermal efficiency, which is 1% and 4.8% higher than diesel with and without H₂ enrichment, respectively. The brake specific fuel consumption of the diesel-ethanol blends with H₂ flow increased with increasing ethanol ratio in the blend. When the ethanol ratio increased from 5 to 10%, in-cylinder pressure and heat release rate were increased, whereas HC, CO, and NO_x emissions were decreased. At maximum load, the CO and HC emission of 10% ethanol blend with 9 lpm H₂ case decreased by about 50% and 28.7% compared to sole diesel. However, NO_x emission of the same blend was 11.4% higher than diesel. From the results, the study concludes that 10% ethanol blended diesel with a 9 lpm H₂ flow rate at the intake port is the best dual-fuel mode combination that gives the best engine characteristics with maximum diesel replacement.     

The effect of clove oil and diesel fuel blends on the engine performance and exhaust emissions of a compression-ignition engine

Diesel engines provide the major power source for transportation in the world and contribute to the prosperity of the worldwide economy. However, recent concerns over the environment, increasing fuel prices and the scarcity of fuel supplies have promoted considerable interest in searching for alternatives to petroleum based fuels. Based on this background, the main purpose of this investigation is to evaluate clove stem oil (CSO) as an alternative fuel for diesel engines. To this end, an experimental investigation was performed on a four-stroke, four-cylinder water-cooled direct injection diesel engine to study the performance and emissions of an engine operated using the CSO–diesel blended fuels. The effects of the CSO–diesel blended fuels on the engine brake thermal efficiency, brake specific fuel consumption (BSFC), specific energy consumption (SEC), exhaust gas temperatures and exhaust emissions were investigated. The experimental results reveal that the engine brake thermal efficiency and BSFC of the CSO–diesel blended fuels were higher than the pure diesel fuel while at the same time they exhibited a lower SEC than the latter over the entire engine load range. The variations in exhaust gas temperatures between the tested fuels were significant only at medium speed operating conditions. Furthermore, the HC emissions were lower for the CSO–diesel blended fuels than the pure diesel fuel whereas the NO_x emissions were increased remarkably when the engine was fuelled with the 50% CSO–diesel blended fuel.     

Performance, emission and combustion characteristics of biodiesel fuelled variable compression ratio engine

Experiments has been carried out to estimate the performance, emission and combustion characteristics of a single cylinder; four stroke variable compression ratio multi fuel engine fuelled with waste cooking oil methyl ester and its blends with standard diesel. Tests has been conducted using the fuel blends of 20%, 40%, 60% and 80% biodiesel with standard diesel, with an engine speed of 1500 rpm, fixed compression ratio 21 and at different loading conditions. The performance parameters elucidated includes brake thermal efficiency, specific fuel consumption, brake power, indicated mean effective pressure, mechanical efficiency and exhaust gas temperature. The exhaust gas emission is found to contain carbon monoxide, hydrocarbon, nitrogen oxides and carbon dioxide. The results of the experiment has been compared and analyzed with standard diesel and it confirms considerable improvement in the performance parameters as well as exhaust emissions. The blends when used as fuel results in the reduction of carbon monoxide, hydrocarbon, carbon dioxide at the expense of nitrogen oxides emissions. It has found that the combustion characteristics of waste cooking oil methyl ester and its diesel blends closely followed those of standard diesel.