Enhancement of heat recirculation on the hysteresis effect of catalytic partial oxidation of methane

The hysteresis characteristics of catalytic partial oxidation of methane (CPOM) in a Swiss-roll reactor are predicted numerically by varying Damköhler number. Particular attention is paid to the influences of heat recirculation, gas hourly space velocity (GHSV), and atomic O/C ratio on the hysteresis loop and performance of CPOM. The reactions of methane combustion, steam reforming, and CO₂ or dry reforming are simultaneously considered. The results reveal that preheating reactants through excess enthalpy recovery is conducive to the ignition of CPOM and extending its extinction limit, so the ignition and extinction Damköhler numbers are lowered. The analysis also suggests that steam reforming is more sensitive to the heat recovery than methane combustion and dry reforming. An increase in GHSV reduces the residence time of reactants in the catalyst bed, thereby enlarging the ignition and extinction Damköhler numbers of CPOM. A higher O/C ratio facilitates the ignition of CPOM, stemming from more oxygen supplied, but the ratio should be controlled below 1.2. From the hysteresis phenomena, hydrogen can be produced from methane at a lower Damköhler number to save more energy for performing CPOM.     

Autothermal reforming of methane for producing high-purity hydrogen in a Pd/Ag membrane reactor

Autothermal reforming of methane includes steam reforming and partial oxidizing methane. Theoretically, the required endothermic heat of steam reforming of methane could be provided by adding oxygen to partially oxidize the methane. Therefore, combining the steam reforming of methane with partial oxidation may help in achieving a heat balance that can obtain better heat efficacy. Membrane reactors offer the possibility of overcoming the equilibrium conversion through selectively removing one of the products from the reaction zone. For instance, only can hydrogen products permeate through a palladium membrane, which shifts the equilibrium toward conversions that are higher than the thermodynamic equilibrium. In this study, autothermal reforming of methane was carried out in a traditional reactor and a Pd/Ag membrane reactor, which were packed with an appropriate amount of commercial Ni/MgO/Al₂O₃ catalyst. A power analyzer was employed to measure the power consumption and to check the autothermicity. The average dense Pd/Ag membrane thickness is 24.3 μm, which was coated on a porous stainless steel tube via the electroless palladium/silver plating procedure. The experimental operating conditions had temperatures that were between 350 °C and 470 °C, pressures that were between 3 atm and 7 atm, and O₂/CH₄ = 0–0.5. The effects of the operating conditions on methane conversion, permeance of hydrogen, H₂/CO, selectivities of CO_x, amount of power supply, and the carbon deposition of the catalyst after the reaction is thoroughly discussed in this paper. The experimental results indicate that an optimum methane conversion of 95%, with a hydrogen production rate of 0.093 mol/m². S, can be obtained from the autothermal reforming of methane at H₂O/CH₄ = 1.3 and O₂/CH₄ near 0.4, at which the reaction does not consume power, and the catalysts are not subject to any carbon deposition.     

Thermodynamic and experimental study of combined dry and steam reforming of methane on Ru/ ZrO2-La2O3 catalyst at low temperature

Analysis of the effect of adding small amounts of steam to the methane dry reforming feed on activity and products distribution was performed from thermodynamic equilibrium calculations of the system based on the Gibbs free energy minimization method. This analysis is supported by new insights from the direct experimental investigation of the influence of co-feeding with H₂O over a Ru/ZrO₂-La₂O₃ catalyst. Activity measurements were carried out in a fixed-bed reactor but using the operating conditions applicable in a Pd membrane reactor, that is, at maximum reaction temperature below 550 °C. Experimental results were in good agreement with thermodynamics predictions. It was observed that the addition of H₂O into the dry reforming feed strongly affects activity and products distribution. The co-feeding of steam resulted in increasing methane conversion and hydrogen yield but decreasing carbon dioxide conversion and carbon monoxide yield. At a given temperature, syngas composition (H₂/CO ratio) can be tuned by changing the amount of H₂O co-fed. Interestingly the stability of the Ru/ZrO₂-La₂O₃ catalyst was improved by adding steam to the dry reforming reactant mixtures.     

CO2 reforming of methane combined with steam reforming or partial oxidation of methane to syngas over NdCoO3 perovskite-type mixed metal-oxide catalyst

CO₂ reforming with simultaneous steam reforming or partial oxidation of methane to syngas over NdCoO₃ perovskite-type mixed metal oxide catalyst (prereduced by H₂) at different process conditions has been investigated. In the simultaneous CO₂ and steam reforming, the conversion of methane and H₂O and also the H₂/CO product ratio are strongly influenced by the CO₂/H₂O feed-ratio. In the simultaneous CO₂ reforming and partial oxidation of methane, the conversion of methane and CO₂, H₂ selectivity and the net heat of reaction are strongly influenced by the process parameters (viz. temperature, space velocity and relative concentration of O₂ in the feed). In both cases, no carbon deposition on the catalyst was observed. The reduced NdCoO₃ perovskite-type mixed-oxide catalyst (Co dispersed on Nd₂O₃) is a highly promising catalyst for carbon-free CO₂ reforming combined with steam reforming or partial oxidation of methane to syngas.     

Demonstration of a scaled-down autothermal membrane methane reformer for hydrogen generation

A novel concept for hydrogen generation by methane steam reforming in a thermally coupled catalytic fixed bed membrane reformer is experimentally demonstrated. The reactor, built from three concentric compartments, indirectly couples the endothermic methane steam reforming with the exothermic methane oxidation, while hydrogen is separated by a permselective Pd membrane. The study focuses on the determination of the key operation parameters and understanding their influence on the reactor performance. It has been shown that the reactor performance is mainly defined by the dimensionless ratio of the methane steam reforming feed flow rate to the hydrogen maximal membrane flow rate and by the ratio of the oxidation and steam reforming methane feed flow rates.     

Simultaneous production of two types of synthesis gas by steam and tri‐reforming of methane using an integrated thermally coupled reactor: mathematical modeling

In this work, tri‐reforming and steam reforming processes have been coupled thermally together in a reactor for production of two types of synthesis gases. A multitubular reactor with 184 two‐concentric‐tubes has been proposed for coupling reactions of tri‐reforming and steam reforming of methane. Tri‐reforming reactions occur in outer tube side of the two‐concentric‐tube reactor and generate the needed energy for inner tube side, where steam reforming process is taking place. The cocurrent mode is investigated, and the simulation results of steam reforming side of the reactor are compared with corresponding predictions for thermally coupled steam reformer and also conventional fixed‐bed steam reformer reactor operated at the same feed conditions. This reactor produces two types of syngas with different H₂/CO ratios. Results revealed that H₂/CO ratio at the output of steam and tri‐reforming sides reached to 1.1 and 9.2, respectively. In this configuration, steam reforming reaction is proceeded by excess generated heat from tri‐reforming reaction instead of huge fired‐furnace in conventional steam reformer. Elimination of a low performance fired‐furnace and replacing it with a high performance reactor causes a reduction in full consumption with production of a new type of synthesis gas. The reactor performance is analyzed on the basis of methane conversion and hydrogen yield in both sides and is investigated numerically for various inlet temperature and molar flow rate of tri‐reforming side. A mathematical heterogeneous model is used to simulate both sides of the reactor. The optimum operating parameters for tri‐reforming side in thermally coupled tri‐reformer and steam reformer reactor are methane feed rate and temperature equal to 9264.4 kmol h^?1 and 1100 K, respectively. By increasing the feed flow rate of tri‐reforming side from 28,120 to 140,600 kmol h^?1, methane conversion and H₂ yield at the output of steam reforming side enhanced about 63.4% and 55.2%, respectively. Also by increasing the inlet temperature of tri‐reforming side from 900 to 1300 K, CH₄ conversion and H₂ yield at the output of steam reforming side enhanced about 82.5% and 71.5%, respectively. The results showed that methane conversion at the output of steam and tri‐reforming sides reached to 26.5% and 94%, respectively with the feed temperature of 1100 K of tri‐reforming side. Copyright © 2013 John Wiley & Sons, Ltd.     

Optimization of tri-reformer reactor to produce synthesis gas for methanol production using differential evolution (DE) method

This paper presents a study on optimization of a fixed bed tri-reformer reactor (TR). This reactor has been used instead of conventional steam reformer (CSR) and auto thermal reformer (CAR). A theoretical investigation has been performed in order to evaluate the optimal operating conditions and enhancement of methane conversion, hydrogen production and desired H₂/CO ratio as a synthesis gas for methanol production. A mathematical heterogeneous model has been used to simulate the reactor. The process performance under steady state conditions was analyzed with respect to key operational parameters (inlet temperature, O₂/CH₄, CO₂/CH₄ and steam/CH₄ ratios). The influence of these parameters on gas temperature, methane conversion, hydrogen production and H₂/CO ratio was investigated. Model validation was carried out by comparison of the reforming model results with industrial data of CSR. Differential evolution (DE) method was applied as a powerful method for optimization. Optimum feed temperature and reactant ratios (CH₄/CO₂/H₂O/O₂) are 1100 K and 1/1.3/2.46/0.47 respectively. The optimized TR has enhanced methane conversion by 3.8% relative to industrial reformers in a single reactor. Methane conversion, hydrogen yield and H₂/CO ratio in optimized TR are 97.9%, 1.84 and 1.7 respectively. The optimization results of tri-reformer were compared with the corresponding predictions from process simulation software operated at the same feed conditions.     

Gas Switching Reforming for syngas production with iron-based oxygen carrier-the performance under pressurized conditions

A four-stage Gas Switching Reforming for syngas production with integrated CO₂ capture using an iron-based oxygen carrier was investigated in this study. The oxygen carrier was first reduced using dry methane, where high methane conversion rate was achieved producing CO₂ and steam. Following the reduction stage is a transition to syngas production in an intermediate stage that begins with partial oxidation of methane while methane cracking dominates the rest of the stage. This results in substantial carbon deposition that gasifies in a subsequent reforming stage by cofeeding steam and methane, contributing to more syngas yield. Some of the deposited carbon that could not gasify during the reforming stage slip to the oxidation stage and get combusted by oxygen in the air feed to release CO₂, thereby reducing the CO₂ capture efficiency of the process. It is in this oxidation stage that heat is being generated for the whole cycle given the high exothermicity nature of this reaction. Methane conversion was found to drop substantially in the reforming stage as the pressure increases driven by the negative effect of pressure on both carbon gasification by steam and on the steam methane reforming. The intermediate stage (after reduction) was found less sensitive to the pressure in terms of methane conversion, but the mechanism of carbon deposition tends to change from methane cracking in the POX stage to Boudouard reaction in the reforming stage. However, methane cracking shows a tendency to reduce substantially at higher pressures. This is could be a promising result indicating that high-pressure operation would remove the need for the reforming stage with steam as no carbon would have been deposited in the POX stage.     

Enhancement effect of heat recovery on hydrogen production from catalytic partial oxidation of methane

The effect of heat recovery on hydrogen production from catalytic partial oxidation of methane (CPOM) and its reaction characteristics in a reactor are investigated using numerical simulations. The reactor is featured by a Swiss-roll structure in which a rhodium (Rh) catalyst bed is embedded at the center of the reactor. By recovering the waste heat from the product gas to preheat the reactants, it is found that the combustion, steam reforming and dry reforming of methane in the catalyst bed are enhanced to a great extent. As a result, the methane conversion and hydrogen yield are improved more than 10%. Considering the operation conditions, a high performance of hydrogen production from CPOM can be achieved if the number of turns in the reactor is increased or the gas hourly space velocity (GHSV) of the reactants in the catalyst bed is lower. However, with the condition of heat recovery, the flow direction of the reactants in the reactor almost plays no part in affecting the performance of CPOM. In summary, the predictions reveal that the reactor with a Swiss-roll structure can be applied for implementing CPOM with high yield of hydrogen.     

Modeling and simulation of methane steam reforming in a thermally coupled membrane reactor

A distributed mathematical model for thermally coupled membrane reactor that is composed of three channels is developed for methane steam reforming. Methane combustion takes place in the first channel on a Pt/δ–Al₂O₃$\text{Pt}/\delta \text{–}{\text{Al}}_2{\text{O}}_3$ catalyst layer that supplies the necessary heat for the endothermic steam reforming reaction. In the second channel, catalytic steam reforming reactions take place in the presence of Ni/MgO–Al₂O₃ catalyst. The combustion catalyst forms a thin layer next to the reactor wall to minimize the heat transfer resistance. Selective permeation of hydrogen through the palladium membrane is achieved either by co-current or counter-current flow of sweep gas through the third channel. The burner is modeled as a monolith reactor and the reformer is assumed to behave as a pseudo-homogenous reactor. The mass and energy balance equations for the thermally coupled membrane reactor form a set of 22 coupled ordinary differential equations. With the application of appropriate boundary conditions, the distributed reactor model for steady-state operation is solved as a boundary value problem. The model equations are discretized using spline collocation on finite elements. The discretized nonlinear modeling equations, along with the boundary conditions, form a system of algebraic equations that are solved using the trust region dogleg method. The performance of the reactor is numerically investigated for various key operating variables such as inlet fuel concentration, inlet steam/methane ratio, inlet reformer gas temperature and inlet reformer gas velocity. Simulations for both the co-current and the countercurrent flow modes are also performed using different sweep gas flow rates. For each case, the reactor performance is analyzed based on methane conversion and hydrogen recovery yield.     

Enhancing efficiency of hydrocarbons to synthesis gas conversion in a counterflow moving bed filtration combustion reactor

An improvement is considered for the partial oxidation conversion of hydrocarbon gases to synthesis gas in a continuous non-premixed filtration combustion reactor with inert solid granular material flowing countercurrently to the gas flow. The reactor is supplemented with an additional heat exchanger, wherein the second reactant gas is preheated prior to supply to the middle part of the reactor. The composition of the gaseous products self-consistent with the temperature of combustion are assessed using approximation of established thermodynamic equilibrium in the products. The parametric domain for major control parameters, namely oxygen-to-fuel supply ratio, granular solid flowrate, and steam supply rate providing highly efficient conversion is determined. Calculations for the POX conversion of methane and a model biogas composition (50% methane, 40% carbon dioxide, 10% nitrogen) with air and steam are provided as examples. The calculations show that the process gives a possibility to substantially improve energy efficiency and provides a flexibility to control hydrogen yield through steam supply. The process provides a high chemical efficiency of conversion even with air used as an oxidant for conversion of low-caloric gases.     

Mini CHP based on the electrochemical generator and impeded fluidized bed reactor for methane steam reforming

The paper presents a configuration of mini CHP with the methane reformer and planar solid oxide fuel cell (SOFC) stacks. This mini CHP may produce electricity and superheated steam as well as preheat air and methane for the reformer along with cathode air used in the SOFC stack as an oxidant. Moreover, the mathematical model for this power plant has been created. The thermochemical reactor with impeded fluidized bed for autothermal steam reforming of methane (reformer) considered as the basis for the synthesis gas (syngas) production to fuel SOFC stacks has been studied experimentally as well. A fraction of conversion products has been oxidized by the air fed to the upper region of the impeded fluidized bed in order to carry out the endothermic methane steam reforming in a 1:3 ratio as well as to preheat products of these reactions. Studies have shown that syngas containing 55% of hydrogen could be produced by this reactor. Basic dimensions of the reactor as well as flow rates of air, water and methane for the conversion of methane have been adjusted through mathematical modelling.The paper provides heat balances for the reformer, SOFC stack and waste heat boiler (WHB) intended for generating superheated water steam along with preheating air and methane for the reformer as well as the preheated cathode air. The balances have formed the basis for calculating the following values: the useful product fraction in the reformer; fraction of hydrogen oxidized at SOFC anode; gross electric efficiency; anode temperature; exothermic effect of syngas hydrogen oxidation by air oxygen; excess entropy along with the Gibbs free energy change at standard conditions; electromotive force (EMF) of the fuel cell; specific flow rate of the equivalent fuel for producing electric and heat energy. Calculations have shown that the temperature of hydrogen oxidation products at SOFC anode is 850 °C; gross electric efficiency is 61.0%; EMF of one fuel cell is 0.985 V; fraction of hydrogen oxidized at SOFC anode is 64.6%; specific flow rate of the equivalent fuel for producing electric energy is 0.16 kg of eq.f./(kW·h) while that for heat generation amounts to 44.7 kg of eq.f./(GJ). All specific parameters are in agreement with the results of other studies.     

Thermodynamic analysis of diesel reforming process: Mapping of carbon formation boundary and representative independent reactions

This paper presents thermodynamic analysis of commercial diesel with 50 ppm sulfur content for the three common modes of reforming operations. Thermodynamic analysis is done to get boundary data for carbon formation and to get the composition of various species for all modes and entire range of operations. For steam reforming operation, steam-to-carbon (S/C) ratio equal to or greater than 2 is required for carbon-free operation in entire temperature range (400–800 °C). However, selection of S/C ratio requires the balance between maximizing the hydrogen yield and minimizing the energy input both of which increase with increasing S/C ratio. For partial oxidation operation, O₂/C ratio of 0.75 is preferable to maximize hydrogen yield but carbon formation can occur if regions of reactor experience temperatures lower than 700 °C. In case of autothermal reforming, for carbon-free operation, temperature of 750 °C, O₂/C ratio in the range of 0.125–0.25 and S/C ratio greater than 1.25 and ideally 1.75 is recommended. However, enthalpy analysis indicates that it is not possible to reach to thermoneutral point at this condition so it is better to operate O₂/C ratio 0.25 or little higher with constant heat supply. A set of three independent reactions is proposed that along with element balance equations can adequately describe the equilibrium composition of six major species—H₂, CO₂, CO, H₂O, CH₄, and C for the entire range of reforming operation.     

Hydrogen production in a zigzag and straight catalytic wall coated micro channel reactor by CFD modeling

Hydrogen production from steam reforming of methanol for fuel cell application was modeled in a wall coated micro channel reactor by CFD approach. Heat of steam reforming (SR) was supplied from catalytic total oxidation (TOX) of methanol on Cu/ZnO/Al₂O₃ catalyst and Heat conducts from TOX to SR zone through Steel divider wall between two channels. Heat integration was compared in zigzag and straight geometry of microreactor by CFD modeling. The model is two dimensional, steady state and containing five zones: TOX fluid, TOX catalyst layer, steel wall of the channel, SR catalyst layer and SR fluid. Set of partial differential equations (PDEs) including x and y momentum balance, continuity, partial mass balances and energy balance was solved by finite volume method. Stiff reaction rates were considered for methanol total oxidation (TOX), methanol steam reforming (SR), water gas shift (WGS) and methanol decomposition (MD) reactions. The results show that zigzag geometry is better than straight one because heat and mass transfer in zigzag reactor are more than straight. Conversion of methanol in zigzag geometry is greater than straight one. In the outlet of zigzag micro channels, carbon monoxide selectivity is less and hydrogen mole fraction is more than straight one.     

Operation of Rh/Ce0.75Zr0.25O2-δ-ƞ-Al2O3/FeCrAl wire mesh honeycomb catalytic modules in diesel steam and autothermal reforming

The Rh/Ce_0·75Zr_0·25O_2–δ-ƞ-Al₂O₃/FeCrAl structured catalytic blocks of length 10, 20, and 60 mm were prepared and tested in the reactions of steam and autothermal reforming of n-hexadecane. It was found in a series of experiments on hexadecane steam reforming with the catalyst heating solely through the reactor wall that the complete conversion of hexadecane at a furnace temperature below 750 °C was not achieved even at GHSV = 10,000 h⁻¹. Under these conditions, the formation of carbon on the catalyst surface was observed. At the reactor wall temperature of 800 °C, the complete conversion of hexadecane was achieved even in the 10 mm long catalytic block (GHSV = 60,000 h⁻¹), accompanied by the formation of various intermediate light hydrocarbons. To achieve complete conversion of these intermediate compounds (mainly 1-alkenes), it is necessary to carry out the steam reforming reaction at GHSV = 10,000 h⁻¹. At hexadecane autothermal reforming, heat is supplied to the reaction zone by exothermic oxidation reaction, which makes this process more efficient. In experiments with the use of additional external heat supply through the reactor wall, complete conversion of hexadecane occurred at GHSV = 120,000 h⁻¹. To convert all by-products (mainly 1-alkenes) and achieve a nearly thermodynamic equilibrium distribution of the main reaction products (H₂, CO, CO₂), the reaction should be carried out at GHSV = 20,000 h⁻¹. Without external heat supply, hexadecane conversion decreased, while the content of light hydrocarbons in the reaction products increased. An increase in the inlet amount of oxygen helps to compensate the heat losses in the reactor and to increase the efficiency of hexadecane autothermal reforming. The performed experiments allow better understanding of the processes which occur during the steam and autothermal reforming of diesel.     

Real-time sensing of methane steam reforming by YSZ oxygen sensor

In this study, a new and convenient technique for the in-situ analyisis of methane steam reforming in the chamber was proposed. The YSZ oxygen sensor was used as the sensing device, which provided the partial pressure of oxygen in the reactor. The oxygen sensors were set in the catalytic bed of 1 wt.% Ni/Al₂O₃ along the gas flow direction and the progress of catalytic reforming was monitored at each position. The methane conversion derived from the oxygen sensor agreed well with that from the gas chromatograph set at the outlet part of the catalyst layer. Along the gas flow direction in the reactor, the change in the gas composition was clearly observed; the methane conversion changed significantly depending on the reaction temperature and space velocity of reactant gas. Furthermore, the deterioration behavior of catalytic activity was successfully monitiored when a highly humidified methane with a steam to carbon ratio of 4.0 was supplied with a high space velocity of 6250 l kg⁻¹ h⁻¹.     

Thermodynamic analysis of hydrogen production via autothermal steam reforming of selected components of aqueous bio-oil fraction

From a technical and economic point of view, autothermal steam reforming offers many advantages, as it minimizes heat load demand in the reformer. Bio-oil, the liquid product of biomass pyrolysis, can be effectively converted to a hydrogen-rich stream. Autothermal steam reforming of selected compounds of bio-oil was investigated using thermodynamic analysis. Equilibrium calculations employing Gibbs free energy minimization were performed for acetic acid, acetone and ethylene glycol in a broad range of temperature (400–1300 K), steam to fuel ratio (1–9) and pressure (1–20 atm) values. The optimal O₂/fuel ratio to achieve thermoneutral conditions was calculated under all operating conditions. Hydrogen-rich gas is produced at temperatures higher than 700 K with the maximum yield attained at 900 K. The ratio of steam to fuel and the pressure determine to a great extent the equilibrium hydrogen concentration. The heat demand of the reformer, as expressed by the required amount of oxygen, varies with temperature, steam to fuel ratio and pressure, as well as the type of oxygenate compound used. When the required oxygen enters the system at the reforming temperature, autothermal steam reforming results in hydrogen yield around 20% lower than the yield by steam reforming because part of the organic feed is consumed in the combustion reaction. Autothermicity was also calculated for the whole cycle, including preheating of the organic feed to the reactor temperature and the reforming reaction itself. The oxygen demand in such a case is much higher, while the amount of hydrogen produced is drastically reduced.     

Comparison of conventional and spherical reactor for the industrial auto-thermal reforming of methane to maximize synthesis gas and minimize CO2

Auto-thermal reforming (ATR), a combination of exothermic partial oxidation and endothermic steam reforming of methane, is an important process to produce syngas for petrochemical industries. In a commercial ATR unit, tubular fixed bed reactors are typically used. Pressure drop across the tube, high manufacturing costs, and low production capacity are some disadvantages of these reactors. The main propose of this study is to offer an optimized radial flow, spherical packed bed reactor as a promising alternative for overcoming the drawbacks of conventional tubular reactors. In the current research, a one dimensional pseudo-homogeneous model based on mass, energy, and momentum balances is applied to simulate the performance of packed-bed reactors for the production of syngas in both tubular and spherical reactors. In the optimization section, the proposed work explores optimal values of various decision variables that simultaneously maximize outlet molar flow rate of H₂, CO and minimize molar flow rate of CO₂ from novel spherical reactor. The multi-objective model is transformed to a single objective optimization problem by weighted sum method and the single optimum point is found by using genetic algorithm. The optimization results show that the pressure drop in the spherical reactor is negligible in comparison to that of the conventional tubular reactor. Therefore, it is inferred that the spherical reactor can operate with much higher feed flow rate, more catalyst loading, and smaller catalyst particles.     

Effect of transition metal on stability and activity of La-Ca-M-(Al)-O (M = Co,Cr, Fe and Mn) perovskite oxides during partial oxidation of methane

Perovskite oxides of the type of La_xCa_1-xM_yAl_1-yO_3-δ (M = Co, Cr, Fe, Mn; x = 0.5; y = 0.7–1.0) were prepared using the polymerization methods and evaluated via N₂ adsorption, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), energy dispersive X-ray (EDX) spectroscopy, temperature-programmed reduction by hydrogen (TPR-H₂) and temperature-programmed oxidation by oxygen (TPO-O₂). Catalytic behaviour of the perovskite oxides during methane oxidation was studied using a tubular fixed-bed reactor. In a partial oxidation, which proceeded in two steps, there was total oxidation in the first step and CO₂ and H₂O were formed; in the second step, the total oxidation products oxidized methane by (dry and wet) reforming reactions to yield CO and H₂. Total oxidation and the two reforming reactions proceeded on two types of an active centre formed by transition metal ions, oxygen vacancies and oxide ions. The catalytic system La-Ca-Co-Al-O which contained aluminium, decomposed in partial oxidation of methane (POM) into a composite that contained firmly bonded cobalt nanoparticles in the surface of a substrate made up of La₂O₃, CaO and Al₂O₃ which catalysed POM with a high methane conversion and hydrogen selectivity.     

Thermochemical waste‐heat recuperation by steam methane reforming with flue gas addition

The process flow schematic of fuel‐consuming equipment with thermochemical waste‐heat recuperation by steam methane reforming with an addition of flue gas to the reaction mixture is suggested. The advantages of such a thermochemical recuperation (TCR) system compared with the TCR system by steam methane reforming are shown and justified. Based on the first law energy analysis, the heat inputs and outputs of the TCR system were determined. To determine the exhaust gases heat transformed into chemical energy of a new synthetic fuel, the thermodynamic analysis by minimizing Gibbs energy via Aspen HYSYS was performed. It was found that with an increase in the mole fraction of combustion products in the reaction mixture, the enthalpy of the methane reforming reaction increases, especially noticeable at the temperature range above 1000 K. Based on the heat, balance of the TCR system was established that the addition of combustion products to the reaction mixture has the following effects: reducing the heat input for steam production in a steam generator; reduction of the steam generator size because of the need to produce a smaller amount of steam in comparison with TCR by pure steam methane reforming; and reducing the amount of heat transferred through the wall of the reformer and, as a consequence, reduction in size of the reformer.