Investigation of forward flow distributed combustion for gas turbine application

New innovative advanced combustion design methodology for gas turbine applications is presented that is focused on the quest towards zero emissions. The new design methodology is called colorless distributed combustion (CDC) and is significantly different from the currently used methodology. In this paper forward flow modes of CDC have been investigated for application to gas turbine combustors. The CDC provides significant improvement in pattern factor, reduced NO_x emission and uniform thermal field in the entire combustion zone for it to be called as an isothermal reactor. Basic requirement for CDC is carefully tailored mixture preparation through good mixing between the combustion air and product gases prior to rapid mixing with fuel so that the reactants are at much higher temperature to result in hot and diluted oxidant stream at temperatures that are high enough to autoignite the fuel and oxidant mixture. With desirable conditions one can achieve spontaneous ignition of the fuel with distributed combustion reactions. Distributed reactions can also be achieved in premixed mode of operation with sufficient entrainment of burned gases and faster turbulent mixing between the reactants. In the present investigation forward flow modes consisting of two non-premixed combustion modes and one premixed combustion mode have been examined that provide potential for CDC. In all the configurations the air injection port is positioned at the opposite side of the combustor exit, whereas the location of fuel injection ports is changed to give different configurations. Two combustion geometries resulting in thermal intensity of 5 MW/m³-atm and 28 MW/m³-atm are investigated. Increase in thermal intensity (lower combustion volume) presents many challenges, such as, lower residence time, lower recirculation of gases and effect of confinement on jet characteristics. The results are presented on the global flame signatures, exhaust emissions, and radical emissions using experiments and flowfield using numerical simulations. Ultra-low NO_x emissions are found for both the premixed and non-premixed combustion modes at the two thermal intensities investigated here. Almost colorless flames (no visible flame signatures) have been observed for the premixed combustion mode. The reaction zone is observed to be significantly different in the two non-premixed modes. Higher thermal intensity case resulted in lower recirculation of gases within the combustion chamber and higher CO levels, possibly due to lower associated residence time. The characteristics at the two thermal intensity combustors investigated here were found to be similar.     

Investigation of reverse flow distributed combustion for gas turbine application

In this paper reverse flow modes of colorless distributed combustion (CDC) have been investigated for application to gas turbine combustors. Rapid mixing between the injected fuel and hot oxidizer has been carefully explored for spontaneous ignition of the mixture to achieve distributed combustion reactions. Distributed reactions can be achieved in premixed, partially premixed or non-premixed modes of combustor operation with sufficient entrainment of burned gases and faster turbulent mixing between the reactants. In the present investigation reverse flow modes consisting of three configurations at thermal intensity of 28 MW/m³-atm and five configurations at thermal intensity of 57 MW/m³-atm have been investigated and these high thermal loadings represent characteristic gas turbine combustion conditions. In all the configurations the air injection port is positioned at the combustor exit end, whereas the location of fuel injection ports is changed to give different configurations. The results are presented on the exhaust emissions and radical emissions using experiments, and evaluation of flowfield using numerical simulations. Ultra-low NO_x emissions were found for both the premixed and non-premixed combustion modes investigated here. Cross-flow configuration, wherein the fuel is injected at high velocity cross stream to the air jet resulted in characteristics closest to premixed combustion mode. Change in fuel injection location resulted in changing the combustion characteristics from closer to diffusion mode to distributed regime. This feature is beneficial for part load operation where higher stability limit is desirable.     

Swirling distributed combustion for clean energy conversion in gas turbine applications

Distributed combustion provides significant performance improvement of gas turbine combustors. Key features of distributed combustion includes uniform thermal field in the entire combustion chamber, thus avoiding hot-spot regions that promote NO_x emissions (from thermal NO_x) and significantly improved pattern factor. Rapid mixing between the injected fuel and hot oxidizer has been carefully explored for spontaneous ignition of the mixture to achieve distributed combustion reactions. Distributed reactions can be achieved in premixed, partially premixed or non-premixed modes of combustor operation with sufficient entrainment of hot and active species present in the flame and their rapid turbulent mixing with the reactants. Distributed combustion with swirl is investigated here for our quest to explore the beneficial aspects of such flows on clean combustion in simulated gas turbine combustion conditions. The goal is to develop high intensity combustor with ultra low emissions of NO and CO, and much improved pattern factor. Experimental results are reported from a cylindrical geometry combustor with different modes of fuel injection and gas exit stream location in the combustor. In all the configurations, air was injected tangentially to impart swirl to the flow inside the combustor. Ultra-low NO_x emissions were found for both the premixed and non-premixed combustion modes for the geometries investigated here. Swirling flow configuration, wherein the product gas exits axially resulted in characteristics closest to premixed combustion mode. Change in fuel injection location resulted in changing the combustion characteristics from traditional diffusion mode to distributed combustion regime. Results showed very low levels of NO (∼3 PPM) and CO (∼70 PPM) emissions even at rather high equivalence ratio of 0.7 at a high heat release intensity of 36 MW/m³-atm with non-premixed mode of combustion. Results are also reported on lean stability limit and OH^* chemiluminescence under both premixed and non-premixed conditions for determining the extent of distribution combustion conditions.     

Development of high intensity CDC combustor for gas turbine engines

Colorless distributed combustion (CDC) has been demonstrated to provide ultra-low emission of NOx and CO, improved pattern factor and reduced combustion noise in high intensity gas turbine combustors. The key feature to achieve CDC is the controlled flow distribution, reduce ignition delay, and high speed injection of air and fuel jets and their controlled mixing to promote distributed reaction zone in the entire combustion volume without any flame stabilizer. Large gas recirculation and high turbulent mixing rates are desirable to achieve distributed reactions thus avoiding hot spot zones in the flame. The high temperature air combustion (HiTAC) technology has been successfully demonstrated in industrial furnaces which inherently possess low heat release intensity. However, gas turbine combustors operate at high heat release intensity and this result in many challenges for combustor design, which include lower residence time, high flow velocity and difficulty to contain the flame within a given volume. The focus here is on colorless distributed combustion for stationary gas turbine applications. In the first part of investigation effect of fuel injection diameter and air injection diameter is investigated in detail to elucidate the effect fuel/air mixing and gas recirculation on characteristics of CDC at relatively lower heat release intensity of 5 MW/m³ atm. Based on favorable conditions at lower heat release intensity the effect of confinement size (reduction in combustor volume at same heat load) is investigated to examine heat release intensity up to 40 MW/m³ atm. Three confinement sizes with same length and different diameters resulting in heat release intensity of 20 MW/m³ atm, 30 MW/m³ atm and 40 MW/m³ atm have been investigated. Both non-premixed and premixed modes were examined for the range of heat release intensities. The heat load for the combustor was 25 kW with methane fuel. The air and fuel injection temperature was at normal 300 K. The combustor was operated at 1 atm pressure. The results were evaluated for flow field, fuel/air mixing and gas recirculation from numerical simulations and global flame images, and emissions of NO, CO from experiments. It was observed that the larger air injection diameter resulted in significantly higher levels of NO and CO whereas increase in fuel injection diameter had minimal effect on the NO and resulted in small increase of CO emissions. Increase in heat release intensity had minimal effect on NO emissions, however it resulted in significantly higher CO emissions. The premixed combustion mode resulted in ultra-low NO levels (<1 ppm) and NO emission as low as 5 ppm was obtained with the non-premixed flame mode.     

Hydrogen addition effects on methane-air colorless distributed combustion flames

In this investigation the role of hydrogen addition in a reverse flow configuration, consisting of both non-premixed and premixed combustion modes, have been examined for the CDC flames. In the non-premixed configuration the air injection port is positioned at combustor exit end while the fuel injection port is positioned on the side so that the fuel is injected in cross-flow with respect to air injection. The thermal intensity of the flames investigated is 85 MW/m³ atm to simulate high thermal intensity gas turbine combustion conditions. The results are presented on the global flame signatures, exhaust emissions, and radical emissions using experiments and flowfield using numerical simulations. Ultra low NO_x emissions are found for both the premixed and non-premixed combustion modes. Addition of hydrogen to methane fuel resulted in only a slight increase of NO emission, significant decrease of CO emission and extended the lean operational limit of the combustor.     

Premixed hydrogen-air combustion system for fuel cell systems

The advance of efficient hydrogen-air combustion systems has increasingly become of interest in the framework of the development of fuel cell systems, especially for the automotive sector. Therefore, compact modulating systems are required, with the additional demand of low emissions, to be integrated in a fuel cell system. A modulating combustion system based on combustion within inert porous media and an integrated heat exchanger has been developed and investigated. The system is able to handle premixed combustion of lean H₂/air mixtures at a surface load range of 1075 kW/m²-2150 kW/m², and a global equivalence ratio of ?=0.5. The special hydrogen-air mixing concept eliminates the risk of flame flashback and enables operation with very low NO_x emissions.     

Mechanism analysis on the pulverized coal combustion flame stability and NOx emission in a swirl burner with deep air staging

Low NOx burner and air staged combustion are widely applied to control NOx emission in coal-fired power plants. The gas-solid two-phase flow, pulverized coal combustion and NOx emission characteristics of a single low NOx swirl burner in an existing coal-fired boiler was numerically simulated to analyze the mechanisms of flame stability and in-flame NOx reduction. And the detailed NOx formation and reduction model under fuel rich conditions was employed to optimize NOx emissions for the low NOx burner with air staged combustion of different burner stoichiometric ratios. The results show that the specially-designed swirl burner structures including the pulverized coal concentrator, flame stabilizing ring and baffle plate create an ignition region of high gas temperature, proper oxygen concentration and high pulverized coal concentration near the annular recirculation zone at the burner outlet for flame stability. At the same time, the annular recirculation zone is generated between the primary and secondary air jets to promote the rapid ignition and combustion of pulverized coal particles to consume oxygen, and then a reducing region is formed as fuel-rich environment to contribute to in-flame NO_X reduction. Moreover, the NOx concentration at the outlet of the combustion chamber is greatly reduced when the deep air staged combustion with the burner stoichiometric ratio of 0.75 is adopted, and the CO concentration at the outlet of the combustion chamber can be maintained simultaneously at a low level through the over-fired air injection of high velocity to enhance the mixing of the fresh air with the flue gas, which can provide the optimal solution for lower NOx emission in the existing coal-fired boilers.     

Study on nonpremixed methane/air combustion from flame structure and NOX emission aspect for different burner head structures

In the present study, the air turbulator, which is a part of a nonpremixed burner, is investigated numerically in terms of its effects on the diffusion methane flame structure and NO_X emissions. A computational fluid dynamics (CFD) code was used for the numerical analysis. At first, four experiments were conducted using natural gas fuel. In the experimental studies, the excess air ratio was taken constant as 1.2, while the fuel consumption rate was changed between 22 and 51 Nm³/h. After the experimental studies, the CFD studies were carried out. Pure methane was taken as fuel for the simulations. The nonpremixed combustion model with the steady laminar flamelet model (SFM) approach was used in the combustion analyses. Methane‐air extinction mechanism with 17 species and 58 reactions was used for the simulations. The results obtained from the CFD studies were confronted with the measurements of the flue gas emissions in the experimental studies. Then, a modified burner head was analysed numerically for the different air turbulator blade numbers and angles. The CFD results show that increasing the air turbulator blade number and angle causes the thermal NO emissions to be reduced in the flue gas by making the flame in the combustion chamber more uniform than the original case. This new flame structure provides better mixing of the fuel and combustion air. Thus, the diffusion flame structure in the combustion chamber takes the form of the partially premixed flame structure. The maximum reduction in the thermal NO emissions in the flue gas is achieved at 38% according to the original case.     

Development and characterization of a low-NOx partially premixed hydrogen burner using numerical simulation and flame diagnostics

The utilization of hydrogen as a fuel in free jet burners faces particular challenges due to its special combustion properties. The high laminar and turbulent flame velocities may lead to issues in flame stability and operational safety in premixed and partially premixed burners. Additionally, a high adiabatic combustion temperature favors the formation of thermal nitric oxides (NO). This study presents the development and optimization of a partially premixed hydrogen burner with low emissions of nitric oxides. The single-nozzle burner features a very short premixing duct and a simple geometric design. In a first development step, the design of the burner is optimized by numerical investigation (Star CCM+) of mixture formation, which is improved by geometric changes of the nozzle. The impact of geometric optimization and of humidification of the combustion air on NO_x emissions is then investigated experimentally. The hydrogen flame is detected with an infrared camera to evaluate the flame stability for different burner configurations. The improved mixture formation by geometric optimization avoids temperature peaks and leads to a noticeable reduction in NO_x emissions for equivalence ratios below 0.85. The experimental investigations also show that NO_x emissions decrease with increasing relative humidity of combustion air. This single-nozzle forms the basis for multi-nozzle burners, where the desired output power can flexibly be adjusted by the number of single nozzles.     

Application of distributed combustion technique to hydrogen-rich coal gases: A numerical investigation

Distributed combustion has been a promising combustion technique, for enabling a more uniform thermal field, resulting in ultra-low pollutant emissions, reduced combustion noise, and enhanced combustion efficiency. This work examines combustion of hydrogen-rich coal gases derived from Turkish coal under distributed combustion conditions. Focus here is on obtaining a broadened flame and reducing pollutant emissions. Numerical modelling was carried out using a commercial code in order to predict the thermal field and pollutant emissions of the hydrogen-rich coal gases under distributed combustion conditions. A gas mixture (90% N₂ and 10% CO₂) was utilized to simulate controlled entrainment of hot reactive product gases into the fresh mixture prior to ignition in order to seek distributed combustion. The results showed that distributed combustion provided far more uniform thermal field that resulted in greatly reduced NOx emissions. The results also showed that the temperature difference between the maximum and exit temperature was reduced to approximately 200 K under distributed conditions. In addition, the NOx pollutant emissions predicted for each gas were reduced to near zero levels under high intensity distributed combustion conditions supporting the available experimental data. It has been concluded that enhanced thermal field uniformity and significantly reduced NOx emissions were achieved for hydrogen-rich coal gases under distributed conditions.