直列透平静叶栅二次流动的数值模拟

采用有发容积差分法及压力修正算法数值求解三维移态时均Ｎ－Ｓ方程组，并应用ｋ－ε湍流模型，在贴体坐标系下对一低展弦比，大转折角的直列透平静叶栅内二次流的产生，发展进行了数值模拟，计算了结果与试验结果吻合良好，从而证实了计算方法的适用性，同时也根据计算结果对静叶栅内二次流涡系的发展及其对气体特性的影响进行了分析。     

数值模拟环形燃烧室两相反应流场

在任意曲线坐标系下,采用一种整体分区结合法,对包扩压器和火焰筒在在内的环形燃烧室三维两相反应流进行了数值模拟。所相采用Ｅｕｌｅｒ方法处理,并采用标准ｋ－ε双方程紊流模型、ＥＢＵ－Ａｒｒｈｅｎｉｕｓ紊流燃烧模型,六通量热辐射模型;液相采用Ｌａｇｒａｎｇｅ法处理。在非交错网格体系下,气相用ＳＩＭＰＬＥ法求解,液相采用颗粒群轨道模型,并用ＰＳＩＣ算法对其进行数值求解,计算结果表明这种新方法是可行的。     

燃气镁合金熔化炉内气相燃烧过程的三维数值模拟

对燃气镁合金熔化炉内的三维湍流气相燃烧场特性进行了数值模拟,湍流模型采用了标准k-ε双方程模型,湍流燃烧采用有限速率/涡耗散模型,辐射换热P1模型,数值方法采用SIMPLE算法,实现了燃烧过程的数值再现,特别考察了烧嘴位置和入口流量速度因素对炉内温度场和流动场的影响,并为熔化炉的结构设计提供了一些合理化建议,为其实际运行提供了有益的参考价值。     

锅炉一次风通过节流孔板时的数值模拟

本文对锅炉燃烧系统水平一次风管道内装了可调节流孔板后的空气－煤粉多相流动情况进行了数值模拟,通过数值模拟发现：采用ｋ－Σ双方程模型描述气相湍流模型,应用ＳＩＭＰＬＥ算法计算气相速度场,然后采用ＦＳＲＴ模型,Ｌａｇｒａｎｇｅ法计算颗粒场特性,这是一种计算管内气固多相流动的行之有效的数值模拟的方法。     

燃气轮机回流式燃烧室内两相流动数值模拟及分析

利用流体分析软件STAR—CD对某回流式燃气轮机燃烧室的内部流场进行了三维冷态数值模拟及两相流反应数值模拟。建立了燃烧室的三维计算几何模型及计算网格,计算了燃烧室的单相流场及喷雾两相流场。在计算中气相采用N-S方程求解,采用高雷诺数κ-ε湍流模型及SIMPISO算法;液相采用Lagrange法处理,采用颗粒群轨道模型。根据计算结果进行流动分析,为进一步进行燃烧室内部燃烧过程的数值计算分析及改善燃烧室的结构设计、降低排放奠定了基础。     

微型燃气轮机燃烧室性能的数值研究

针对Capstone公司的C30微型燃气轮机的燃烧室，采用κ—ε湍流模型、EBU—Ambenius湍流燃烧模型描述其燃烧流动，采用扩展Zeldivch机制描述HOx生成；应用分区结构化网格和SIMPLE算法求解控制方程，进行了三维燃烧流动的数值模拟研究，同时对燃烧室的整体性能进行了分析。通过数值计算及结果分析，着重研究了环型贫燃预混燃烧室的燃烧组织形式对燃烧室性能的影响，并探讨了流动控制板对燃烧室内燃烧流动和燃烧室出口HOx分布的影响。数值研究的主要目的是配合新型微型燃气轮机的研制，获得微型燃气轮机燃烧室的设计经验，为研制既有高燃烧效率和燃烧稳定性，又有低HOx排放特性的燃烧室奠定基础。     

PaSR湍流燃烧模型对典型湍流射流火焰的数值模拟

采用PaSR湍流燃烧模型对湍流燃烧研究中典型的甲烷湍流射流火焰进行了数值模拟.计算采用简化的化学反应机理,并将计算得到的平均温度场、速度场和各组分的分布与相应的权威实验数据进行了对比.对反应系统中流动和燃烧的不同时间尺度以及二者之间的关系作了探讨.计算结果表明,PaSR模型能够很好地模拟燃烧过程中流场和组分的变化.在火...     

煤粉复合旋流火焰燃烧特性研究（2）：数值模拟

本文数值模拟了煤粉旋流火焰燃烧过程，燃烧数值计算包括理论物理模型建立，数值方法两个大部分，计算模型处理了气相湍流与燃烧、气固两相流动、煤颗粒燃烧过程和辐射传热等物理化学过程，以ｋ－ε模型模拟湍流流动；ＰＤＦ法模拟气相扩散火焰燃烧；颗粒运动计算颗粒运动少颗粒湍流浓度方程模拟颗粒湍流扩散；通量法计算火焰辐射传热，煤粉颗粒复杂燃烧模型计算了颗粒尺寸、形状变化和颗粒孔隙内部燃烧、表面平度对整个颗粒的燃烧过程影响。计算获得了气相速度分布场、气相ｋ和ε分布场、气相温度场、气相组份场和颗粒浓度场及运动过程，揭示了煤粉复合旋流燃烧特性。     

MPI环境下气固两相流动的并行计算

采用Fortran语言自行开发的程序,在非正交贴体坐标系下,采用k-ε-Ap模型.模型的两相湍流模型对一新型燃烧器一次风喷嘴及弯头组件内的气固两相流动进行了数值模拟.在求解过程中,将整个几何区域分解成若干相对简单的子区域,然后分别在各子域上采用SIMPLEC算法对控制方程组进行离散多机并行求解.最后本文分析了计算机集群在数值求解复杂流动问题方面的实用性以及实际所能达到的计算效率.     

等离子发生器燃烧流场的数值模拟

采用漩涡破碎(EBU)燃烧模型、κ-ε双方程湍流模型及SIMPLEC算法对等离子发生器内部的燃烧流场进行了数值模拟,得到温度场、压力场以及湍流脉动动能、湍流平均动能耗散率等参数分布图。     

Performance assessment of some ice TES systems

In this paper, a performance assessment of four main types of ice storage techniques for space cooling purposes, namely ice slurry systems, ice-on-coil systems (both internal and external melt), and encapsulated ice systems is conducted. A detailed analysis, coupled with a case study based on the literature data, follows. The ice making techniques are compared on the basis of energy and exergy performance criteria including charging, discharging and storage efficiencies, which make up the ice storage and retrieval process. Losses due to heat leakage and irreversibilities from entropy generation are included. A vapor-compression refrigeration cycle with R134a as the working fluid provides the cooling load, while the analysis is performed in both a full storage and partial storage process, with comparisons between these two. In the case of full storage, the energy efficiencies associated with the charging and discharging processes are well over 98% in all cases, while the exergy efficiencies ranged from 46% to 76% for the charging cycle and 18% to 24% for the discharging cycle. For the partial storage systems, all energy and exergy efficiencies were slightly less than that for full storage, due to the increasing effect wall heat leakage has on the decreased storage volume and load. The results show that energy analyses alone do not provide much useful insight into system behavior, since the vast majority of losses in all processes are a result of entropy generation which results from system irreversibilities.     

Effect of co-cultivation of Chlamydomonas reinhardtii with Azotobacter chroococcum on hydrogen production

Chlamydomonas reinhardtii cc124 and Azotobacter chroococcum bacteria were co-cultured with a series of volume ratios and under a variety of light densities to determine the optimal culture conditions and to investigate the mechanism by which co-cultivation improves H₂ yield. The results demonstrated that the optimal culture conditions for the highest H₂ production of the combined system were a 1:40 vol ratio of bacterial cultures to algal cultures under 200 μE m^?2 s^?1. Under these conditions, the maximal H₂ yield was 255 μmol mg^?1 Chl, which was approximately 15.9-fold of the control. The reasons for the improvement in H₂ yield included decreased O₂ content, enhanced algal growth, and increased H₂ase activity and starch content of the combined system.     

Aerodynamic performance effects of leading-edge geometry in gas-turbine blades

The purpose of this paper is to illustrate the advantages of the direct surface-curvature distribution blade-design method, originally proposed by Korakianitis, for the leading-edge design of turbine blades, and by extension for other types of airfoil shapes. The leading edge shape is critical in the blade design process, and it is quite difficult to completely control with inverse, semi-inverse or other direct-design methods. The blade-design method is briefly reviewed, and then the effort is concentrated on smoothly blending the leading edge shape (circle or ellipse, etc.) with the main part of the blade surface, in a manner that avoids leading-edge flow-disturbance and flow-separation regions. Specifically in the leading edge region we return to the second-order (parabolic) construction line coupled with a revised smoothing equation between the leading-edge shape and the main part of the blade. The Hodson–Dominy blade has been used as an example to show the ability of this blade-design method to remove leading-edge separation bubbles in gas turbine blades and other airfoil shapes that have very sharp changes in curvature near the leading edge. An additional gas turbine blade example has been used to illustrate the ability of this method to design leading edge shapes that avoid leading-edge separation bubbles at off-design conditions. This gas turbine blade example has inlet flow angle 0°, outlet flow angle −64.3°, and tangential lift coefficient 1.045, in a region of parameters where the leading edge shape is critical for the overall blade performance. Computed results at incidences of −10°,   −5°,   +5°,   +10° are used to illustrate the complete removal of leading edge flow-disturbance regions, thus minimizing the possibility of leading-edge separation bubbles, while concurrently minimizing the stagnation pressure drop from inlet to outlet. These results using two difficult example cases of leading edge geometries illustrate the superiority and utility of this blade-design method when compared with other direct or inverse blade-design methods.     

Natural-gas fueled spark-ignition (SI) and compression-ignition (CI) engine performance and emissions

Natural gas is a fossil fuel that has been used and investigated extensively for use in spark-ignition (SI) and compression-ignition (CI) engines. Compared with conventional gasoline engines, SI engines using natural gas can run at higher compression ratios, thus producing higher thermal efficiencies but also increased nitrogen oxide (NO_x) emissions, while producing lower emissions of carbon dioxide (CO₂), unburned hydrocarbons (HC) and carbon monoxide (CO). These engines also produce relatively less power than gasoline-fueled engines because of the convergence of one or more of three factors: a reduction in volumetric efficiency due to natural-gas injection in the intake manifold; the lower stoichiometric fuel/air ratio of natural gas compared to gasoline; and the lower equivalence ratio at which these engines may be run in order to reduce NO_x emissions. High NO_x emissions, especially at high loads, reduce with exhaust gas recirculation (EGR). However, EGR rates above a maximum value result in misfire and erratic engine operation. Hydrogen gas addition increases this EGR threshold significantly. In addition, hydrogen increases the flame speed of the natural gas-hydrogen mixture. Power levels can be increased with supercharging or turbocharging and intercooling. Natural gas is used to power CI engines via the dual-fuel mode, where a high-cetane fuel is injected along with the natural gas in order to provide a source of ignition for the charge. Thermal efficiency levels compared with normal diesel-fueled CI-engine operation are generally maintained with dual-fuel operation, and smoke levels are reduced significantly. At the same time, lower NO_x and CO₂ emissions, as well as higher HC and CO emissions compared with normal CI-engine operation at low and intermediate loads are recorded. These trends are caused by the low charge temperature and increased ignition delay, resulting in low combustion temperatures. Another factor is insufficient penetration and distribution of the pilot fuel in the charge, resulting in a lack of ignition centers. EGR admission at low and intermediate loads increases combustion temperatures, lowering unburned HC and CO emissions. Larger pilot fuel quantities at these load levels and hydrogen gas addition can also help increase combustion efficiency. Power output is lower at certain conditions than diesel-fueled engines, for reasons similar to those affecting power output of SI engines. In both cases the power output can be maintained with direct injection. Overall, natural gas can be used in both engine types; however further refinement and optimization of engines and fuel-injection systems is needed.     

Exergetic evaluation of 5 biowastes-to-biofuels routes via gasification

This paper presents the exergy analysis results for the production of several biofuels, i.e., SNG (synthetic natural gas), methanol, Fischer–Tropsch fuels, hydrogen, as well as heat and electricity, from several biowastes generated in the Dutch province of Friesland, selected as one of the typical European regions. Biowastes have been classified in 5 virtual streams according to their ultimate and proximate analysis. All production chains have been modeled in Aspen Plus in order to analyze their technical performance. The common steps for all the production chains are: pre-treatment, gasification, gas cleaning, water–gas-shift reactions, catalytic reactors, final gas separation and upgrading. Optionally a gas turbine and steam turbines are used to produce heat and electricity from unconverted gas and heat removal, respectively. The results show that, in terms of mass conversion, methanol production seems to be the most efficient process for all the biowastes. SNG synthesis is preferred when exergetic efficiency is the objective parameter, but hydrogen process is more efficient when the performance is analyzed by means of the 1st Law of Thermodynamics. The main exergy losses account for the gasification section, except in the electricity and heat production chain, where the combined cycle is less efficient.     

Hydrogen production by steam-gasification of carbonaceous materials using concentrated solar energy – V. Reactor modeling,optimization, and scale-up

A chemical reactor for the steam-gasification of carbonaceous particles (e.g. coal, coke) is considered for using concentrated solar radiation as the energy source of high-temperature process heat. A two-phase reactor model that couples radiative, convective, and conductive heat transfer to the chemical kinetics is applied to optimize the reactor geometrical configuration and operational parameters (feedstock's initial particle size, feeding rates, and solar power input) for maximum reaction extent and solar-to-chemical energy conversion efficiency of a 5 kW prototype reactor and its scale-up to 300 kW. For the 300 kW reactor, complete reaction extent is predicted for an initial feedstock particle size up to 35 μm at residence times of less than 10 s and peak temperatures of 1818 K, yielding high-quality syngas with a calorific content that has been solar-upgraded by 19% over that of the petcoke gasified.     

液压系统常见的故障诊断及处理

任何工程机械式液压设备使用时出现故障是不可避免的。但是怎样确定故障的原因及找到好的解决方法,这是使用者最关心的问题。讲述了液压系统常见的故障及其排除方法。     

汽轮机数字电液调节系统挂闸异常的技术完善

分析了200MW汽轮机数字电液调节系统在运行中存在的挂闸异常问题,采取了相应的技术处理措施,且运行实践效果良好。     

新型高压共轨ECU升压模块的数字化开发与优化

为了提高喷油器电磁阀的响应速率,提出了一种基于CPLD(复杂可编程逻辑器件)应用于高压共轨ECU的数字升压模块。鉴于该升压电路结构参数多,其升压电压的恢复响应要求高等特征,基于Pspice建立了升压电路的仿真模型,研究了不同电路参数下升压模块的输出特性,全面优化了该升压模块的性能。结果显示,该升压模块的最大转换效率可以达90%以上。在柴油发动机上对ECU的试验表明,升压电压最大波动不超过10%,其恢复时间仅为1.3ms,功率管最大温升仅为41℃,满足整机运行范围内ECU的需求。     

Trace metal chemistry and silicification of microorganisms in geothermal sinter, Taupo Volcanic Zone, New Zealand

As part of a pilot study investigating the role of microorganisms in the immobilisation of As, Sb, B, Tl and Hg, the inorganic geochemistry of seven different active sinter deposits and their contact fluids were characterised. A comprehensive series of sequential extractions for a suite of trace elements was carried out on siliceous sinter and a mixed silica-carbonate sinter. The extractions showed whether metals were loosely exchangeable or bound to carbonate, oxide, organic or crystalline fractions. Hyperthermophilic microbial communities associated with sinters deposited from high temperature (92–94°C) fluids at a variety of geothermal sources were investigated using SEM. The rapidity and style of silicification of the hyperthermophiles can be correlated with the dissolved silica content of the fluid. Although high concentrations of Hg and Tl were found associated with the organic fraction of the sinters, there was no evidence to suggest that any of the heavy metals were associated preferentially with the hyperthermophiles at the high temperature (92–94°C) ends of the terrestrial thermal spring ecosystems studied.