MoS2/NiFeS2 heterostructure as a highly efficient electrocatalyst for overall water splitting at high current densities

Searching for efficient, stable and low-cost nonprecious catalysts for oxygen and hydrogen evolution reactions (OER and HER) is highly desired in overall water splitting (OWS). Herein, presented is a nickel foam (NF)-supported MoS₂/NiFeS₂ heterostructure, as an efficient electrocatalyst for OER, HER and OWS. The MoS₂/NiFeS₂/NF catalyst achieves a 500 mA cm⁻² current density at a small overpotential of 303 mV for OER, and 228 mV for HER. Assembled as an electrolyzer for OWS, such a MoS₂/NiFeS₂/NF heterostructure catalyst shows a quite low cell voltage (≈1.79 V) at 500 mA cm⁻², which is among the best values of current non-noble metal electrocatalysts. Even at the extremely large current density of 1000 mA cm⁻², the MoS₂/NiFeS₂/NF catalyst presents low overpotentials of 314 and 253 mV for OER and HER, respectively. Furthermore, MoS₂/NiFeS₂/NF shows a ceaseless durability over 25 h with almost no change in the cell voltage. The superior catalytic activity and stability at large current densities (>500 mA cm⁻²) far exceed the benchmark RuO₂ and Pt/C catalysts. This work sheds a new light on the development of highly active and stable nonprecious electrocatalysts for industrial water electrolysis.     

Electrochemically engineering defect-rich nickel-iron layered double hydroxides as a whole water splitting electrocatalyst

It is well proved that fabricating more defects on basal plane of layered double hydroxides (LDHs) is one of effective ways to boost the electrocatalytic performance for oxygen evolution reaction (OER). For the first time, the nickel iron LDHs (NiFe LDHs) with hierarchical morphology and abundant defects are simultaneously constructed by one-step electrodeposition (ED) strategy with easy operation, time-saving and green chemistry. Remarkably, the morphology is elaborately tailored by changing the species of doped anions which is unique. Also, the X-ray photoelectron spectroscopy (XPS) results elucidate that the Fe sites are in electron-rich state in LDHs which is revealed to enhance the catalytic activity strongly arising from the generation of oxygen vacancy. To deliver the current density of 10 mA cm⁻², the optimal NiFe LDHs require the overpotential of 128, 106 mV for OER and hydrogen evolution reaction (HER), and achieve 100 mA cm⁻² at the overpotential of 237, 242 mV, respectively. As a bifunctional electrocatalyst, the NiFe LDHs exhibit the current density of 10 mA cm⁻² at a cell voltage of 1.55 V and 100 mA cm⁻² at 1.76 V, which are lower than that of most of benchmarking materials reported previously.     

Facile construction of well-defined hierarchical NiFe2O4/NiFe layered double hydroxides with a built-in electric field for accelerating water splitting at the high current density

Interfacial charge redistribution induced by a strong built-in electric field can expertly optimize the adsorption energy of hydrogen and hydroxide for improving the catalytic activity. Herein, we develop a well-defined hierarchical NiFe₂O₄/NiFe layered double hydroxides (NFO/NiFe LDH) catalysts, exhibiting superior performance due to the strong interfacial electric field interaction between NiFe₂O₄ nanoparticle layers and NiFe LDH nanosheets. In 1 M KOH, NFO/NiFe LDH needs 251 mV and 130 to drive 50 and 10 mA cm^?2 for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER). Moreover, only 1.517 V cell voltage is needed to reach 10 mA cm^?2 towards overall water splitting. Notably, under simulated industrial electrolysis conditions, NFO/NiFe LDH only needs 289 mV to drive 1000 mA cm^?2. This work puts a deep insight into the role of the built-in electric field in transition metal-based catalysts for accelerating water splitting and scalable industrial electrolysis applications.     

Co-based MOF-derived Co/CoN/Co2P ternary composite embedded in N- and P-doped carbon as bifunctional nanocatalysts for efficient overall water splitting

In this work, we developed ternary metallic cobalt-cobalt nitride-dicobalt phosphide composite embedded in nitrogen and phosphorus co-doped carbon (Co/CoN/Co₂P-NPC) as bifunctional catalysts for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). The as-prepared Co/CoN/Co₂P-NPC is achieved by simultaneous annealing and phosphating of a Co–N rich metal-organic frameworks (MOFs) precursor. Compare with the phosphorus-free Co/CoN embedded nitrogen-doped carbon electrocatalyst (Co/CoN-NC), the as-prepared Co/CoN/Co₂P-NPC display superior HER and OER low overpotential of 99 mV and 272 mV at current density of 10 mA cm⁻². When Co/CoN/Co₂P-NPC electrocatalyst is use as bifunctional catalysts in overall alkaline water splitting, it exhibit excellent behaviour with 10 mA cm⁻² current at overall cell potential of 1.60 V. The excellent performance of Co/CoN/Co₂P-NPC electrocatalyst is attributed to the phosphating process that could further enhance synergistic effect, create stronger electronic interactions, and form efficient dual heteroatom doping to optimize the interfacial adhesion within the electrocatalyst. This present work will create more opportunities for the development of new, promising and more active sites electrocatalysts for alkaline electrolysis.     

Mesoporous spinel NiFe oxide cubes as advanced electrocatalysts for oxygen evolution

Oxygen evolution reaction (OER) is the rate-controlling step of the electrochemical water splitting. The slow kinetics hinders large-scale H₂ production. Herein, the spinel NiFe oxides were prepared by directly pyrolyzing nickel hexacynoferrate precursors in air. The NiFe oxides were presented as mesoporous nanocubes with a specific surface area of 125 m² g⁻¹. The mesoporous spinel NiFe oxide nanocubes can afford a geometric current of 10 mA cm⁻² at a low overpotential of a 0.24 V and a small Tafel slope of 41 mV dec⁻¹ in alkaline solution. The specific activity can reach up to 0.37 mA cm⁻² with a turnover frequency of 0.93 s⁻¹. The superior OER activity of the NiFe oxide nanocubes (NiFeO NCs) can outperform those of the state-of-the-art IrO₂ catalysts, and compare favorably with other spinel transition metal oxides reported recently under identical condition. NiFeO NCs also show a long-term durability without significant loss of the OER activity. Our works provide a new strategy to develop efficient, robust and earth-abundant spinel NiFe oxides as advanced OER electrocatalysts to replace the expensive commercial IrO₂ catalysts for water splitting in the industrial scale.     

Porous NiFe alloys synthesized via freeze casting as bifunctional electrocatalysts for oxygen and hydrogen evolution reaction

Binder-free NiFe-based electrocatalyst with aligned pore channels has been prepared by freeze casting and served as a bifunctional catalytic electrode for oxygen and hydrogen evolution reaction (OER and HER). The synergistic effects between Ni and Fe result in the high electrocatalytic performance of porous NiFe electrodes. In 1.0 M KOH, porous Ni₇Fe₃ attains 100 mA cm⁻² at an overpotential of 388 mV with a Tafel slope of 35.8 mV dec⁻¹ for OER, and porous Ni₉Fe₁ exhibits a low overpotential of 347 mV at 100 mA cm⁻² with a Tafel slope of 121.0 mV dec⁻¹ for HER. The Ni₉Fe₁//Ni₉Fe₁ requires a low cell voltage of 1.69 V to deliver 10 mA cm⁻² current density for overall water splitting. The excellent durability at a high current density of porous NiFe electrodes has been confirmed during OER, HER and overall water splitting. The fine electrocatalytic performances of the porous NiFe-based electrodes owing to the three-dimensionally well-connected scaffolds, aligned pore channels, and bimetallic synergy, offering excellent charge/ion transfer efficiency and sizeable active surface area. Freeze casting can be applied to design and synthesize various three-dimensionally porous non-precious metal-based electrocatalysts with controllable multiphase for energy conversion and storage.     

Vertical Nickel–Iron layered double hydroxide nanosheets grown on hills-like nickel framework for efficient water oxidation and splitting

Herein, the vertical thin nickel–iron layered double hydroxide nanosheets grown on the hills-like nickel framework (NiFe LDH/Ni@NF) are employed for the oxygen evolution reaction (OER), securing at the low overpotentials of 197 and 270 mV to obtain the current densities of 20 and 100 mA cm⁻², respectively, with a Tafel slope of 73.34 mV dec⁻¹. The electrodeposited nickel film induces the NiFe LDH nanosheets grow vertically and thinly. As well, the nickel abundant interfaces and inner space makes this catalyst effective for OER. It was further served as the OER electrode in a water splitting system coupled the Pt/C cathode, and a cell voltage was at 1.52 and 1.67 V to achieve the current density of 10 mA cm⁻² and 50 mA cm⁻². In addition, the water electrolyzer can suffer a long time of 24 h at 50 mA cm⁻², showing the feasibility in a practical unbiased alkaline water splitting system.     

Cu2S@NiFe layered double hydroxides nanosheets hollow nanorod arrays self-supported oxygen evolution reaction electrode for efficient anion exchange membrane water electrolyzer

Herein, we prepared highly active self-supported Cu₂S@NiFe layered double hydroxides nanosheets (LDHs) oxygen evolution reaction (OER) electrode (Cu₂S@NiFe LDHs/Cu foam) with three-dimensional (3D) multilayer hollow nanorod arrays structure, which is composed of the outer layer (two-dimensional (2D) NiFe LDHs) and the inner layer (one-dimensional (1D) Cu₂S hollow nanorod arrays). The unique structure of NiFe LDHs and Cu₂S hollow nanorod composites can expose more active sites, and simultaneously promote electrolyte penetration and gas release during the water electrolysis process. Thus, the Cu₂S@NiFe LDHs/Cu foam electrode exhibits a significant OER performance, with the overpotentials of 230 and 286 mV at 50 and 100 mA cm⁻², respectively. Anion exchange membrane water electrolyzer (AEMWE) with the prepared electrode can attain a voltage of 1.56 V at the current density of 0.50 A cm⁻², showing a good performance that is comparable to the-state-of-the-art AEMWE in 1 M KOH. In addition, the AEMWE can be run for 300 h at the current density of 0.50 A cm⁻². The high performance and good stability of AEMWE are attributed to the special structure of the OER electrode, which can prevent the agglomeration of nanosheets and thus expose more active sites at the edge of the nanosheets.     

Co–NiFe layered double hydroxide nanosheets as an efficient electrocatalyst for the electrochemical evolution of oxygen

The development of non-precious metal catalysts for the electrochemical oxygen evolution reaction (OER) is especially important for the water electrolysis process. Herein, a two-dimensional (2D) ultrathin hybrid Co–NiFe layered double hydroxide (LDH) is synthesized via a facile hydrothermal method. In 1.0 M KOH electrolyte, Co–NiFe LDH exhibits remarkable activities for OER. At the current density of 10 mA cm⁻², it only needs an overpotential of 278 mV, which is ca. 50 mV and 20 mV lower than those for NiFe LDH (328 mV) and RuO₂ catalysts (298 mV), respectively. In addition, Co–NiFe LDH also shows impressive long-term stability for OER. Besides the stable morphology and crystal structure, the potential is always kept at 1.50 V and shows almost no attenuation during the 20 h of durability test. Changes in the electronic structure of LDH due to introduction of Co ions, as well as the large specific surface area facilitate the mass/electron transfer and the oxygen bubbles release, and thus lead to the enhanced catalytic properties for OER. This work can be informative not only for understanding the role of physical and electronic structures on OER but also for designing high-performance non-precious metal OER electrocatalysts.     

Mo-incorporated three-dimensional hierarchical ternary nickel-cobalt-molybdenum layer double hydroxide for high-efficiency water splitting

Flowers-like 3D hierarchical ternary NiCoMo-layered double hydroxide (NiCoMo-LDH) spheres have been fabricated in substrate-free route via a one-pot hydrothermal method and utilized as efficient electrocatalysts for the OER and HER. The well-structured 3D hierarchical flowers were composed of numerous two-dimensional nanosheets, which inherently possess considerable electrochemical active sites, thereby enhancing catalytic activity. NiMo and CoMo binary LDHs, with similar morphology, were also prepared to illustrate the efficiency of the ternary LDH. The results indicate higher electrocatalytic activity for the ternary LDH as compared to binary LDHs under alkaline conditions. The NiCoMo-LDH required an overpotential as low as 202 and 93 mV to deliver a constant anodic and cathodic current density of 10 mA cm^?2 for the OER and HER, respectively. Furthermore, the NiCoMo-LDH exhibited remarkable HER activity, affording a low overpotential of 198 mV at a current density of ?100 mA cm^?2. Moreover, it could offer a stable current density of 10 mA cm^?2 for overall water splitting at 1.62 V in 1 M KOH with long-term stability for 20 h. The double-layer capacitance (C_dl) value indicated that the NiCoMo-LDH significantly influenced interface conductivity and the electrochemical active surface area. The ternary NiCoMo-LDH electrode yielded low Tafel slope values of 54 and 51 mVdec^?1 for the OER and HER. Owing to the efficient incorporation of Ni, Co, and Mo in a layered structure, synergetic effect, and high electrochemical surface area, the NiCoMo-LDH exhibited remarkable electrocatalytic activity. Such eco-friendly ternary LDHs can be used in rechargeable metal–air batteries for industrial applications.     

Accelerated oxygen evolution kinetics on NiFeAl-layered double hydroxide electrocatalysts with defect sites prepared by electrodeposition

NiFe layered double hydroxides (LDHs) is considered to be one of the LDHs electrocatalyst materials with the best electrocatalytic oxygen evolution properties. However, its poor conductivity and inherently poor electrocatalytic activity are considered to be the limiting factors inhibiting the electrocatalytic properties for oxygen evolution reaction (OER). The amorphous NiFeAl-LDHs electrocatalysts were prepared by electrodeposition with nickel foam as the support, and the D-NiFeAl-LDHs electrocatalyst with defect sites was then obtained by alkali etching. The mechanism of catalysts with defect sites in OER was analyzed. The ingenious defects can selectively accelerate the adsorption of OH⁻, thus enhancing the electrochemical activity. The D-NiFeAl-LDHs electrocatalyst had higher OER electrocatalytic activity than NiFe-LDHs electrocatalyst: its accelerated OER kinetics were mainly due to the introduction of iron and nickel defects in NiFeAl-LDHs nanosheets, which effectively adjusted the surface electronic structure and improved OER electrocatalytic performance. There was only a low overpotential of 262 mV with the current density of 10 mA cm⁻², and the Tafel slope was as low as 41.67 mV dec⁻¹. The OER electrocatalytic performance of D-NiFeAl-LDHs was even better than those of most of the reported NiFe-LDHs electrocatalysts.     

One-pot solvothermal synthesis of Co2P nanoparticles: An efficient HER and OER electrocatalysts

Development of an inexpensive electrocatalyst for hydrogen evolution (HER) and oxygen evolution reactions (OER) receives much traction recently. Herein, we report a facile one-pot ethyleneglycol (EG) mediated solvothermal synthesis of orthorhombic Co₂P with particle size ~20–30 nm as an efficient HER and OER catalysts. Synthesis parameters like various solvents, temperatures, precursors ratios, and reaction time influences the formation of phase pure Co₂P. Investigation of Co₂P as an electrocatalyst for HER in acidic (0.5 M H₂SO₄) and alkaline medium (1.0 M KOH), furnishes low overpotential of 178 mV and 190 mV, respectively to achieve a 10 mA cm^?2 current density with a long term stability and durability. As an OER catalyst in 1.0 M KOH, Co₂P shows an overpotential of 364 mV at 10 mA cm^?2 current density. Investigation of Co₂P NP by XPS analysis after OER stability test under alkaline medium confirms the formation of amorphous cobalt oxyhydroxide (CoOOH) as an intermediate during OER process.     

Hydrogen production via highly efficient electrocatalyst based on 3D NixCo1-x(OH)2/NiFe-AM induce overall water splitting

The main factors limiting water splitting producing hydrogen production are overpotential, activity and persistence of electrocatalysts. Herein, a novel Ni_xCo_1-x(OH)₂ coupled with NiFe amorphous compound array growing on nickel foam substrate (expressed as Ni_xCo_1-x(OH)₂/NiFe-AM) was developed by facile hydrothermal and electrodeposition methods. Significantly, Ni_xCo_1-x(OH)₂/NiFe-AM with this unique structural exhibits superior activity and stability in the two half reactions of water electrolysis. In addition, when tested in an alkaline electrolyte with a current density of 10 mA cm⁻², the overpotentials of HER and OER was 157 mV and 196 mV (60 mA cm⁻²), respectively. The stability can up to 60 h. These test results show through constructing hierarchical nano-thron architecture enhanced electrocatalytic activity to produce hydrogen and oxygen.     

The P/NiFe doped NiMoO4 micro-pillars arrays for highly active and durable hydrogen/oxygen evolution reaction towards overall water splitting

Water splitting is an efficient strategy to produce purity hydrogen and convert intermittent electricity from renewable wind and solar sources. In this work, dense NiMoO₄ micro-pillars arrays (MPAs) were in-situ grown on nickel foam (NF) through facile hydrothermal method, then the NiMoO₄/NF were converted into NiMoO₄–P/NF and NiFe/NiMoO₄/NF via phosphating and electrodeposition method, respectively. The NiMoO₄–P/NF electrode required small overpotentials of 34 mV@10 mA cm⁻² and 130 mV@100 mA cm⁻² for hydrogen evolution reaction (HER). The NiFe/NiMoO₄/NF electrode exhibited excellent oxygen evolution reaction (OER) activity with overpotentials of 210 mV@10 mA cm⁻² and 300 mV@100 mA cm⁻². The overall water splitting using the anode-cathode couple of NiFe/NiMoO₄/NF||NiMoO₄–P/NF only consumes low voltages of 1.47 V@10 mA cm⁻² for 100 h and 1.66 V@100 mA cm⁻² for 50 h in 1 M KOH. The electronic modification and the well-designed hierarchical structure contribute the high energy-efficient and stabile overall water splitting.     

Superhydrophilic 3D peony flower-like Mo-doped Ni2S3@NiFe LDH heterostructure electrocatalyst for accelerating water splitting

Constructing highly efficient nonprecious electrocatalysts for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is essential to improve the efficiency of overall water splitting, but still remains lots of obstacles. Herein, a novel 3D peony flower-like electrocatalyst was synthesized by employing Mo–Ni₂S₃/NF nanorod arrays as scaffolds to in situ growth ultrathin NiFe LDH nanosheets (Mo-Ni₂S₃@NiFe LDH). As expected, the novel peony flower-like Mo–Ni₂S₃@NiFe LDH displays superior electrocatalytic activity and stability for both OER and HER in alkaline media. Low overpotentials of only 228 mV and 109 mV are required to achieve the current densities of 50 mA cm^?2 and 10 mA cm^?2 for OER and HER, respectively. Additionally, the material remarkably accelerates water splitting with a low voltage of 1.54 V at 10 mA cm^?2, which outperforms most transition metal electrodes. The outstanding electrocatalytic activity benefits from the following these features: 3D peony flower-like structure with rough surface provides more accessible active sites; superhydrophilic surfaces lead to the tight affinity between electrode with electrolyte; metallic Ni substrate and highly conductive Mo–Ni₂S₃ nanorods scaffold together with offer fast electron transfer; the nanorod arrays and porous Ni foam accelerate gas bubble release and ions transmission; the strong interfacial effect between Mo-doped Ni₃S₂ and NiFe LDH shortens transport pathway, which are benefit for electrocatalytic performance enhancement. This work paves a new avenue for construction and fabrication the 3D porous structure to boost the intrinsic catalytic activities for energy conversion and storage applications.     

Electrodeposition of NiS/Ni2P nanoparticles embedded in amorphous Ni(OH)2 nanosheets as an efficient and durable dual-functional electrocatalyst for overall water splitting

To develop earth-abundant and cost-effective catalysts for overall water splitting is still a major challenge. Herein, a unique “raisins-on-bread” Ni–S–P electrocatalyst with NiS and Ni₂P nanoparticles embedded in amorphous Ni(OH)₂ nanosheets is fabricated on Ni foam by a facile and controllable electrodeposition approach. It only requires an overpotential of 120 mV for HER and 219 mV for OER to reach the current density of 10 mA cm⁻² in 1 M KOH solution. Employed as the anode and cathode, it demonstrates extraordinary electrocatalytic overall water splitting activity (cell voltage of only 1.58 V @ 10 mA cm⁻²) and ultra-stability (160 h @ 10 mA cm⁻² or 120 h @50 mA cm⁻²) in alkaline media. The synergetic electronic interactions, enhanced mass and charge transfers at the heterointerfaces facilitate HER and OER processes. Combined with a silicon PV cell, this Ni–S–P bifunctional catalyst also exhibits highly efficient solar-driven water splitting with a solar-to-hydrogen conversion efficiency of 12.5%.     

Okra-like hollow Cu0.15-CoP/Co3O4@CC nanotube arrays catalyst for overall water splitting

The manufacture of hydrogen energy by overall water splitting (OWS) has been broadly considered as a promising candidate for constant energy systems. Herein, we report an okra-like hollow Cu_0.15-CoP/Co₃O₄@CC nanotube arrays catalyst through a simple hydrothermal-phosphating method. As a noble-metal-free catalyst, it exhibits outstanding HER (hydrogen evolution reaction) catalytic activity with an overpotential of 13 mV to achieve 10 mA cm^?2 in 1 M KOH electrolyte. For OER (oxygen evolution reaction), it demands 225 mV to achieve 10 mA cm^?2. When okra-like hollow Cu_0.15-CoP/Co₃O₄@CC is used as both cathode and anode electrode materials, 1.487 V is required to reach 10 mA cm^?2 for OWS, better than numerous electrocatalysts that have been reported. Moreover, it displays excellent stability in a continuously 60 h i-t test, proving an enormous potential for large-scale applications. The theoretical calculation of density functional theory (DFT) further reveals that Cu doping can bring localized structure polarization and reduce the hydrogen adsorption free energy (ΔG_H1) on the interstitial sites, thus leading to a significant increase in catalytic activity.     

Growth of ultrathin nanosheets of nickel iron layered double hydroxide for the oxygen evolution reaction

Because of low cost and abundance, nickel-iron double layered hydroxide (NiFe LDH) is seen as a viable substitute for noble-metal-based electrodes for the oxygen evolution reaction (OER). Herein, we report the growth of NiFe LDH in the form of fine nanosheets in a single step using benzyl alcohol-mediated chemistry. The electrochemical studies clearly suggest that benzyl alcohol is capable of inducing effective chemical interaction between Ni and Fe in the NiFe LDH. The overpotential to produce benchmark 10 mA cm^?2 (η₁₀) for the NiFe LDH electrode is only ～270 mV_RHE, which is much smaller than those of benchmark IrO₂ (η₁₀ = 318 mV_RHE), nickel hydroxide (η₁₀ = 370 mV_RHE) and iron hydroxide (η₁₀ = 410 mV_RHE) for the OER. The difference of the overpotential requirement increases further with increasing current density, indicating faster kinetics of the OER at the catalytic interface of the NiFe LDH. Estimation of Tafel values verifies this notion – the Tafel slopes of NiFe LDH, Ni(OH)₂, and FeOOH are calculated to be 48.6, 55.8, and 59.3 mV dec^?1, respectively. At η = 270 mV, the turnover frequency (TOF) of the NiFe LDH is 0.48 s^?1, which is ～8 and ～11 folds higher than those of Ni(OH)₂ (0.059 s^?1) and FeOOH (0.042 s^?1). In addition to Tafel and TOF, the NiFe LDH electrode has favorable electrochemically active surface area and electrochemical impedance. The electrochemical stability of the NiFe LDH electrode is assessed by conducting potentiostatic measurements at η = 270 mV_RHE (～10 mA cm^?2) and at η = 355 mV_RHE (～30 mA cm^?2) for 24 h of continuous oxygen production.     

Tailoring the activity of NiFe layered double hydroxide with CeCO3OH as highly efficient water oxidation electrocatalyst

Owing to the efficient modulation of the electronic structure of nanomaterials, rare earth elements introduction as promoters into nanomaterials has attracted great attention in oxygen evolution reaction (OER). This work demonstrates the cerium carbonate hydroxide (CeCO₃OH) in situ grown on nickel foam (NF) supported NiFe layered double hydroxide (LDH) as a novel promoter in OER process. The hybrid material (Ni_0.75Fe_0.15Ce_0.10/NF) possesses excellent performance for OER where the overpotentials at the current densities of 10 mA cm^?2 and 100 mA cm^?2 are 228 mV and 270 mV, respectively, along with the Tafel slope of 38.3 mV dec^?1. Such performance is comparable in activity to many state-of-the-art electrocatalysts. The enhanced performance in the NiFe LDH can be ascribed to the synergetic interaction between CeCO₃OH and NiFe LDH by utilizing the advantages of cerium and carbonate in OER. The novelty of our work is the exploration of CeCO₃OH as a promoter to enhance the OER performance, which expands the application of cerium-based compounds in energy storage and conversion.     

NiFe layered double hydroxide nanosheet arrays for efficient oxygen evolution reaction in alkaline media

Exploring efficient oxygen evolution reaction (OER) catalysts synthesized from low-cost and earth-abundant elements are crucial to the progression of water splitting. In this paper, NiFe layered double hydroxide (LDH) nanosheets were grown on Ni foam (NF) through a straightforward hydrothermal method. The Fe doping effects were systematically investigated by controlling Ni/Fe ratios and Fe valence states, and the in-depth influence mechanisms were discussed. The results indicate that, through controlling structure morphology and enhancing Ni²⁺ oxidation, NiFe_III(1:1)-LDH displays the best and outstanding OER performance, with a low over potential of 382 mV at 50 mA cm^?2, a low Tafel slope of 31.1 mVdec^?1 and only 20 mV increase after 10 h continuous test at 50 mA cm^?2. To our knowledge, this is one of the best OER electrocatalysts in alkaline media to date. This work provides a facile and novel strategy for the fabrication of bimetallic LDH catalysts with desired structures and compositions.