Comparison of sulfonated and other micropollutants removal in membrane bioreactor and conventional wastewater treatment

Membrane bioreactors (MBRs) were compared with conventional activated sludge systems (CAS) for micropollutant degradation, in laboratory-scale spiking experiments with synthetic and real domestic wastewater. The target micropollutants were polar in nature and represented a broad range in biodegradability. The experimental data indicated that MBR treatment could significantly enhance removal of the micropollutants 1,6- and 2,7-naphthalene disulfonate (NDSA) and benzothiazole-2-sulfonate. 1,5-NDSA, EDTA and diclofenac were not removed in either the MBR or the CAS. The other compounds were equally well degraded in both systems. For 1,3-naphthalene disulfonate, the existence of a minimum threshold level for degradation could be demonstrated. Although MBRs could not always make a difference in the overall removal efficiencies achieved, they showed reduced lag phases for degradation and a stronger memory effect, which implies that they may respond quicker to variable influent concentrations. Finally, micropollutant removal also turned out to be less sensitive to system operational variables.     

Effect of temperature shocks on membrane fouling in membrane bioreactors

Temperature is known to influence the biological performance of conventional activated sludge systems. In membrane bioreactors (MBRs), temperature not only affects the bioconversion process but is also shown to have an effect on the membrane performance. Four phenomena are generally reported to explain the higher resistance for membrane filtration found at lower temperatures: (1) increased mixed liquor viscosity, reducing the shear stress generated by coarse bubbles, (2) intensified deflocculation, reducing biomass floc size and releasing EPS into the mixed liquor, (3) lower backtransport velocity and (4) reduced biodegradation of COD. Although the higher resistance at low temperatures has been reported in several papers, the relation with supernatant composition has not been investigated before. In this paper, the composition of the soluble fraction of the mixed liquor is related to membrane performance after exposing the sludge to temperature shocks. Flux step experiments were performed in an experimental system at 7, 15, and 25° Celsius with sludge that was continuously recirculated from a pilot-scale MBR. After correcting the permeate viscosity for temperature, higher membrane fouling rates were obtained for the lower temperature in combination with low fouling reversibility. The soluble fraction of the MBR mixed liquor was analysed for polysaccharides, proteins and submicron particle size distribution. At low temperature, a high polysaccharide concentration was found in the experimental system as compared to the MBR pilot. Upon decreasing the temperature of the mixed liquor, a shift was found in particle size towards smaller particles. These results show that the release of polysaccharides and/or submicron particles from sludge flocs could explain the increased membrane fouling at low temperatures.     

Fate of aromatic hydrocarbons in Italian municipal wastewater systems: An overview of wastewater treatment using conventional activated-sludge processes (CASP) and membrane bioreactors (MBRs)

We studied the occurrence, removal, and fate of 16 polycyclic aromatic hydrocarbons (PAHs) and 23 volatile organic compounds (VOCs) in Italian municipal wastewater treatment systems in terms of their common contents and forms, and their apparent and actual removal in both conventional activated-sludge processes (CASP) and membrane bioreactors (MBRs). We studied five representative full-scale CASP treatment plants (design capacities of 12 000 to 700 000 population-equivalent), three of which included MBR systems (one full-scale and two pilot-scale) operating in parallel with the conventional systems. We studied the solid-liquid partitioning and fates of these substances using both conventional samples and a novel membrane-equipped automatic sampler. Among the VOCs, toluene, ethylbenzene, xylenes, styrene, 1,2,4-trimethylbenzene, and 4-chlorotoluene were ubiquitous, whereas naphthalene, acenaphthene, fluorene, and phenanthrene were the most common PAHs. Both PAHs and aromatic VOCs had removal efficiencies of 40-60% in the headworks, even in plants without primary sedimentation. Mainly due to volatilization, aromatic VOCs had comparable removal efficiencies in CASP and MBRs, even for different sludge ages. MBRs did not enhance the retention of PAHs sorbed to suspended particulates compared with CASPs. On the other hand, the specific daily accumulation of PAHs in the MBR’s activated sludge decreased logarithmically with increasing sludge age, indicating enhanced biodegradation of PAHs. The PAH and aromatic VOC contents in the final effluent are not a major driver for widespread municipal adoption of MBRs, but MBRs may enhance the biodegradation of PAHs and their removal from the environment.     

Novel magnetically induced membrane vibration (MMV) for fouling control in membrane bioreactors

Conventional submerged membrane bioreactors (MBRs) rely on the coarse bubbles aeration to generate shear at the liquid-membrane interface to limit membrane fouling. Unfortunately, it is a very energy consuming method, still often resulting in a rapid decrease of membrane permeability and consequently in higher expenses. In this paper, the feasibility of a novel magnetically induced membrane vibration (MMV) system was studied in a lab-scale MBR treating synthetic wastewater. The effects on membrane fouling of applied electrical power of different operation strategies, of membrane flux and of the presence of multiple membranes on one vibrating engine on membrane fouling were investigated. The filtration performance was evaluated by determining the filtration resistance profiles and critical flux. The results showed clear advantages of the vibrating system over conventional MBR processes by ensuring higher fluxes at lower fouling rates. Intermittent vibration was found a promising strategy for both efficient fouling control and significant energy saving. The optimised MMV system is presumed to lead to significant energy and cost reduction in up-scaled MBR operations.     

The influence of aeration intensity on predation and EPS production in membrane bioreactors

Shear, in the form of vigorous aeration, is used to control fouling in membrane bioreactor (MBR) systems. However, shear also influences the physicochemical and biological properties of MBR biomass. The current study examines the relationship between the aeration intensity and extracellular polymeric substance (EPS) production in MBRs. Two identical submerged MBRs were operated in parallel but the aeration rate was three times greater in one of the MBRs. The concentrations of floc-associated and soluble EPS were monitored for the duration of the experiment. Microscopic images and floc-size measurements were also collected regularly. The membrane fouling potential of the biomass was quantified using the flux-step method. Increased aeration did not have a direct effect on soluble or floc-associated EPS production in the microfiltration MBRs. However, aeration intensity had a significant effect on predatory organisms. Large aquatic earthworms, Aeolosoma hemprichi, proliferated under lower shear conditions but were never observed in the high shear reactor. Predation by A. hemprichi resulted in increased floc-associated and soluble EPS production. Thus, the mixing conditions in the low shear MBR indirectly resulted in increased soluble EPS concentrations and higher fouling potential. This research suggests that predation can have a significant impact on the production rates of floc-associated and soluble EPS - key parameters driving membrane fouling in MBRs.     

Activated sludge model (ASM) based modelling of membrane bioreactor (MBR) processes: A critical review with special regard to MBR specificities

Membrane bioreactors (MBRs) have been increasingly employed for municipal and industrial wastewater treatment in the last decade. The efforts for modelling of such wastewater treatment systems have always targeted either the biological processes (treatment quality target) as well as the various aspects of engineering (cost effective design and operation). The development of Activated Sludge Models (ASM) was an important evolution in the modelling of Conventional Activated Sludge (CAS) processes and their use is now very well established. However, although they were initially developed to describe CAS processes, they have simply been transferred and applied to MBR processes. Recent studies on MBR biological processes have reported several crucial specificities: medium to very high sludge retention times, high mixed liquor concentration, accumulation of soluble microbial products (SMP) rejected by the membrane filtration step, and high aeration rates for scouring purposes. These aspects raise the question as to what extent the ASM framework is applicable to MBR processes. Several studies highlighting some of the aforementioned issues are scattered through the literature. Hence, through a concise and structured overview of the past developments and current state-of-the-art in biological modelling of MBR, this review explores ASM-based modelling applied to MBR processes. The work aims to synthesize previous studies and differentiates between unmodified and modified applications of ASM to MBR. Particular emphasis is placed on influent fractionation, biokinetics, and soluble microbial products (SMPs)/exo-polymeric substances (EPS) modelling, and suggestions are put forward as to good modelling practice with regard to MBR modelling both for end-users and academia. A last section highlights shortcomings and future needs for improved biological modelling of MBR processes.     

Biomass characteristics of two types of submerged membrane bioreactors for nitrogen removal from wastewater

Biomass characteristics and microbial community diversity between a submerged membrane bioreactor with mixed liquor recirculation (MLE/MBR) and a membrane bioreactor with the addition of integrated fixed biofilm medium (IFMBR) were compared for organic carbon and nitrogen removal from wastewater. The two bench-scale MBRs were continuously operated in parallel at a hydraulic retention time (HRT) of 24 h and solids retention time (SRT) of 20 d. Both MBRs demonstrated good COD removal efficiencies (>97.7%) at incremental inflow organic loading rates. The total nitrogen removal efficiencies were 67% for MLE/MBR and 41% for IFMBR. The recirculation of mixed liquor from aerobic zone to anoxic zone in the MLE/MBR resulted in higher microbial activities of heterotrophic (46.96 mg O₂/gVSS h) and autotrophic bacteria (30.37 mg O₂/gVSS h) in the MLE/MBR compared to those from IFMBR. Terminal Restriction Fragment Length Polymorphism analysis indicated that the higher nitrifying activities were correlated with more diversity of nitrifying bacterial populations in the MLE/MBR. Membrane fouling due to bacterial growth was evident in both the reactors. Even though the trans-membrane pressure and flux profiles of MLE/MBR and IFMBR were different, the patterns of total membrane resistance changes had no considerable difference under the same operating conditions. The results suggest that metabolic selection via alternating anoxic/aerobic processes has the potential of having higher bacterial activities and improved nutrient removal in MBR systems.     

Influence of shear on the production of extracellular polymeric substances in membrane bioreactors

Shear is used to control fouling in membrane bioreactor (MBR) systems. However, shear also influences the physicochemical and biological properties of MBR biomass. The current study examines the relationship between the level of shear and extracellular polymeric substance (EPS) production in MBRs. Two identical MBRs were operated in parallel where the biomass in one reactor was exposed to seven times greater shear forces. The concentrations of floc-associated and soluble EPS were monitored for the duration of the experiment. The stickiness of extracted floc-associated EPS from each reactor was also characterized using atomic force microscopy. A mathematical model of floc-associated and soluble EPS production was applied to quantitatively describe changes in EPS production with shear. Biomass grown in a high shear environment has lower floc-associated EPS production compared to biomass grown in a lower shear environment. This decrease in floc-associated EPS production also corresponds to a decrease in soluble EPS production, which can be explained by both the lower concentration of floc-associated EPS and the production of stickier floc-associated EPS that is more erosion resistant in the high shear reactor. This research suggests that mechanical stresses can have a significant impact on the production rates of floc-associated and soluble EPS—key parameters governing membrane fouling in MBRs.     

Relation between EPS adherence, viscoelastic properties, and MBR operation: Biofouling study with QCM-D

Membrane fouling is one of the main constraints of the wide use of membrane bioreactor (MBR) technology. The biomass in MBR systems includes extracellular polymeric substances (EPS), metabolic products of active microbial secretion that adversely affect the membrane performance. Solids retention time (SRT) in the MBR is one of the most important parameters affecting membrane fouling in MBR systems, where fouling is minimized at optimal SRT. Among the operating parameters in MBR systems, SRT is known to strongly influence the ratio of proteins to polysaccharides in the EPS matrix. In this study, we have direct evidence for changes in EPS adherence and viscoelastic properties due to changes in the sludge removal rate that strongly correlate with the membrane fouling rate and EPS composition. EPS were extracted from a UF membrane in a hybrid growth MBR operated at sludge removal rates of 59, 35.4, 17.7, and 5.9 L day^-1 (corresponding SRT of 3, 5, 10, and 30 days, respectively). The EPS adherence and adsorption kinetics were carried out in a quartz crystal microbalance with dissipation monitoring (QCM-D) technology in several adsorption measurements to a gold sensor coated with Polyvinylidene Fluoride (PVDF). EPS adsorption to the sensor surface is characterized by a decrease of the oscillation frequency and an increase in the dissipation energy of the sensor during parallel flow of aqueous media, supplemented with EPS, above the sensor surface. The results from these experiments were further modeled using the Voigt based model, in which the thickness, shear modulus, and shear viscosity values of the adsorbed EPS layers on the PVDF crystal were calculated. The observations in the QCM-D suggested that the elevated fouling of the UF membrane is due to higher adherence of the EPS as well as reduction in viscosity and elasticity of the EPS adsorbed layer and elevation of the EPS fluidity. These results corroborate with confocal laser scanning microscopy (CLSM) image analysis showing thicker EPS in close proximity to the membrane surface operated at reactor conditions which induced more fouling at elevated sludge removal rates.     

Modeling cake buildup under TMP-step filtration in a membrane bioreactor: cake compressibility is significant

Fouling is inevitable in membrane bioreactors (MBRs) due to the complex nature of activated sludge, which contains a broad variety of potential foulants. Filter cakes that build up from sludge particles are traditionally highly compressible due to both the deformation of the individual sludge particles and the rearrangement of these particles in the cake. However, this phenomenon has been little examined in studies of fouling mechanisms in MBR systems. This study examines the properties of the cake layer, modeling the cake buildup and specific cake resistance (α), including compressibility, in terms of pressure-dependent α.The changes in fouling resistance during transmembrane pressure (TMP)-step filtration in an MBR setup were simulated using an empirical pressure dependence of the specific cake resistance and a simple mass balance model. The total change in fouling resistance in each TMP step could be divided into an initial rapid change in specific cake resistance due to filter cake compression followed by simple cake buildup. By including cake compression in this simple model, the model fitted the data with high precision. We demonstrated that compressibility should be considered when describing cake fouling in MBRs.     

Side-stream membrane bioreactors: Influence of stress generated by hydrodynamics on floc structure, supernatant quality and fouling propensity

This work aims to characterise the impact of hydrodynamics on sludge properties and consequently on fouling mechanisms in side-stream membrane bioreactors (MBRs). Two side-stream processes which generate very different shear stresses are compared, without filtration. This operating mode permits specific quantification of the impact of the external loop (and of induced shear stress) on floc structure/morphology, supernatant quality and fouling propensity. The study shows that low constraints (7 × 10⁻³ Pa) generated on submerged side-stream hollow fibre modules have no significant impact on sludge properties. In contrast, high shear stresses (72 Pa) associated with a crossflow configuration induce very significant modifications of the mixed liquor which increases its fouling propensity (measured in a standard filtration cell). A theoretical explanation of the role of turbulence on the floc size distribution is given. Based on a Kolmogorov microscale calculation, it seems possible to predict the mean floc size reached in both filtration systems, for a given shear stress intensity. Disaggregation is characterised by a two-step kinetic: first a short-term breakage attributed to fragmentation and loss of weak strength bonds, and secondly a longer-term breakage probably due to erosion phenomena and removal of high strength bonds. Only the second step induces a significant release and an accumulation of soluble protein-like substances. Soluble organic matter strongly enhances the fouling propensity of the mixed liquor. This seems to be amplified by the concentration of protein-like substances. The importance of considering the protein and carbohydrate content as well as floc size is also pointed out in the paper.     

Further examination of polysaccharides causing membrane fouling in membrane bioreactors (MBRs): Application of lectin affinity chromatography and MALDI-TOF/MS

Membrane fouling remains a major obstacle for wider application of membrane bioreactors (MBRs) to wastewater treatment. Polysaccharides in mixed liquor suspensions in the reactors are thought to be mainly responsible for the evolution of membrane fouling in MBRs. However, details of polysaccharides causing membrane fouling in MBRs are still unknown. In this study, polysaccharides in a mixed liquor suspension of a pilot-scale MBR treating municipal wastewater were fractionated by using lectins, special proteins that bind to specific polysaccharides depending on their properties. Fouling potentials of the fractionated polysaccharides were assessed by bench-scale dead-end filtration tests. It was clearly shown that the degrees of fouling caused by fractionated polysaccharides were significantly different. The amounts of polysaccharides in each fraction could not explain the variations in the fouling, indicating the presence of polysaccharides with high specific fouling potentials. To investigate structures and origins of the polysaccharides with high fouling potentials, matrix-assisted laser desorption/ionization (MALDI)-time of flight (TOF)/mass spectrometry (MS) analysis was applied to the fractionated polysaccharides after partial hydrolysis. Several mass peaks obtained could be assigned to fragments of structures of polysaccharides (i.e., oligosaccharides) reported in a database/literature. This is the first report showing the plausible structures of polysaccharides in MBRs based on MS. A deeper understanding and effective control of membrane fouling in MBRs could be achieved with information obtained by the approach used in this study.     

Changes in characteristics of soluble microbial products in membrane bioreactors associated with different solid retention times: Relation to membrane fouling

A membrane bioreactor (MBR) is a promising wastewater treatment technology, but there is a need for efficient control of membrane fouling, which increases operational and maintenance costs. Soluble microbial products (SMP) have been reported to act as major foulants in the operation of MBRs used for wastewater treatment. In this study, SMP in MBRs operated with different sludge retention times (SRTs) were investigated by means of various analytical techniques and their relations to the evolution of membrane fouling were considered. Bench-scale filtration experiments were carried out in a laboratory with synthetic wastewater to eliminate fluctuations that would occur with the use of real wastewater and that would lead to fluctuations in compositions of SMP. Three identical submerged MBRs were operated for about 50 days under the same conditions except for SRT (17, 51 and 102 days). Accumulation of SMP in the MBRs estimated by conventional analytical methods (i.e., the phenol-sulfuric acid method and the Lowry method) was significant in the cases of short SRTs. However, the degrees of membrane fouling in the MBRs were not directly related to the concentrations of SMP in the reactors estimated by the conventional analytical methods. Non-conventional analytical methods such as excitation-emission matrix (EEM) fluorescence spectroscopy revealed that characteristics of SMP in the three reactors considerably differed depending on SRT. Foulants were extracted from the fouled membranes at the end of the operation and were compared with SMP in each MBR. It was clearly shown that characteristics of the foulants were different depending on SRT, and similarities between SMP and the extracted foulants were recognized in each MBR on the basis of results of EEM measurements. However, such similarities were not found on the basis of results obtained by using the conventional methods for analysis of SMP. The results of this study suggest that the use of conventional methods for analysis of SMP is not appropriate for investigation of membrane fouling in MBRs.     

Removal of selected pharmaceuticals, fragrances and endocrine disrupting compounds in a membrane bioreactor and conventional wastewater treatment plants

Eight pharmaceuticals, two polycyclic musk fragrances and nine endocrine disrupting chemicals were analysed in several waste water treatment plants (WWTPs). A membrane bioreactor in pilot scale was operated at different solid retention times (SRTs) and the results obtained are compared to conventional activated sludge plants (CASP) operated at different SRTs. The SRT is an important design parameter and its impact on achievable treatment efficiencies was evaluated. Different behaviours were observed for the different investigated compounds. Some compounds as the antiepileptic drug carbamazepine were not removed in any of the sampled treatment facilities and effluent concentrations in the range of influent concentrations were measured. Other compounds as bisphenol-A, the analgesic ibuprofen or the lipid regulator bezafibrate were nearly completely removed (removal rates >90%). The operation of WWTPs with SRTs suitable for nitrogen removal (SRT>10 days at 10 degrees C) also increases the removal potential regarding selected micropollutants. No differences in treatment efficiencies were detected between the two treatment techniques. As in conventional WWTP also the removal potential of MBRs depends on the SRT. Ultrafiltration membranes do not allow any additional detention of the investigated substances due to size exclusion. However, MBRs achieve a high SRT within a compact reactor. Nonylphenolpolyehtoxylates were removed in higher extend in very low-loaded conventional WWTPs, due to variations of redox conditions, necessary for the degradation of those compounds.     

投加颗粒活性炭对膜生物反应器过滤特性的影响

膜污染是制约膜技术应用的重要因素。向膜生物反应器(MBR)中投加颗粒活性炭(GAC),通过分析MBR系统中膜通量、过滤阻力等的变化,考察投加GAC对MBR系统过滤特性的影响。结果表明,运行30d后,未投加和投加GAC的MBR系统的膜通量分别降至初始的31.3%和91.7%;未投加GAC系统的总过滤阻力和极化阻力分别为投加GAC系统的5.8和19.4倍,其污泥的多糖和蛋白质含量为投加GAC系统的近2倍,而其胶体物质和溶解性物质浓度分别为投加GAC系统的3.2和2.2倍。由此表明,投加GAC可大大减缓膜污染,延长膜的过滤周期。     

Correlation of EPS content in activated sludge at different sludge retention times with membrane fouling phenomena

In this study, activated sludge characteristics were studied with regard to membrane fouling in membrane bioreactors (MBRs) for two pilot plants and one full-scale plant treating municipal wastewater. For the full-scale MBR, concentrations of extracellular polymeric substances (EPS) bound to sludge flocs were shown to have seasonal variations from as low as 17mgg(-1) dry matter (DM) in summer up to 51mg(gDM)(-1) in winter, which correlated with an increased occurrence of filamentous bacteria in the colder season. Therefore, it was investigated at pilot-scale MBRs with different sludge retention times (SRTs) whether different EPS contents and corresponding sludge properties influence membrane fouling. Activated sludge from the pilot MBR with low SRT (23d) was found to have worse filterability, settleability and dewaterability. Photometric analysis of EPS extracts as well as LC-OCD measurements showed that it contained significantly higher concentrations of floc-bound EPS than sludge at higher SRT (40d) The formation of fouling layers on the membranes, characterised by SEM-EDX as well as photometric analysis of EPS extracts, was more distinct at lower SRT where concentrations of deposited EPS were 40-fold higher for proteins and 5-fold higher for carbohydrates compared with the membrane at higher SRT. Floc-bound EPS and metals were suggested to play a role in the fouling process at the full-scale MBR and this was confirmed by the pilot-scale study. However, despite the different sludge properties, the permeability of membranes was found to be similar.     

Influence of organic and inorganic flocculants on physical-chemical properties of biomass and membrane-fouling rate

The effects of addition of six types of flocculants (aluminium sulfate, ferric chloride, polyaluminium chloride, polymeric ferric sulfate, Chitosan, polyacrylamide) on mitigation of membrane fouling in membrane bioreactors (MBR) were investigated respectively. The biomasses in various MBRs were characterized by morphological properties (mean floc size (d_p), fractal dimension (df)), physical parameters (surface charge, relative hydrophobicity (RH), dynamic viscosity) and the biochemical components of the mixed liquor (extracellular polymeric substances (EPS), soluble microbial products (SMP)). Statistical methods such as normalization, nondimensionalization and multiple linear regressions were used to identify the dominant membrane-fouling contributors and to simulate membrane-fouling rates. The results demonstrated that addition of flocculants had significant impact on sustainable filtration time and the key factors affecting membrane fouling varied in different flocculants added MBRs. For the organic flocculants added MBRs, membrane-fouling alleviation was mainly due to the decrease in SMP and df as well as the increase in d_p. For the inorganic flocculants added MBRs, the lower fouling rate could be mainly attributed to the decrease in SMP and surface charge as well as the increase in RH. For each type of flocculants, the empirical equations of sustainable filtration time (Γ₄₅) were simulated to predict membrane-fouling rates in different MBRs.     

Removal of a synthetic organic chemical by PAC-UF systems. II: Model application

This paper describes several application potentials with a recently developed model for predicting the synthetic organic chemical (SOC) removal by powdered activated carbon (PAC) adsorption during ultrafiltration (UF) and discusses the removal mechanism. The model was successfully applied, without any modification, to dead-end mode operation as well as to cross-flow mode operation, validating the assumption of the internal diffusion control mechanism and the continuously-stirred-tank-reactor (CSTR) concept. Even when UF was operated in a cross-flow mode, PAC added was re-circulating in suspension for only a short time. Then, solute uptake took place mostly by PAC immobilized in membrane tubes not only for dead-end operation but also for cross-flow operation. Therefore, cross-flow operation did not have any advantage regarding the SOC mass transfer on PAC in UF loop over dead-end operation. The model simulation implied that pulse PAC addition at the beginning of filtration cycle resulted better SOC removal than continuous PAC addition. However, for the pulse PAC addition mode, the model predicted somewhat lower effluent SOC concentration than the observed values, and the benefit of pulse PAC application in terms of reducing SOC over its continuous dosage was not confirmed. Longer detention time of PAC dosed in a pulse than continuously dosed PAC could possibly further decrease internal diffusivity.     

Consequences of mass transfer effects on the inetics of nitrifiers

The influence of membrane separation and mass transfer effects on the kinetics of nitrifiers was evaluated by running a membrane bioreactor (MBR) and a conventional activated sludge (CAS) plant in parallel. Both pilot plants were operated at the same sludge age and treated the same domestic wastewater. The half-saturation constants for the substrate were low in both MBR and CAS and did not differ significantly between the two processes (K(NH(4))) and 0.14+/-0.10 g(N)m(-3) and (K(NO(2))) and 0.28+/-0.20 g(N)m(-3) for the MBR and CAS, respectively). However, the half-saturation constants for oxygen exhibited a major difference between the two processes for both the ammonia-oxidizing (AOB) and nitrite-oxidizing (NOB) bacteria. The experiments yielded K(O,AOB)=0.18+/-0.04 and 0.79+/-0.08 g(O2) as well as K(O,NOB)=0.13+/-0.06 and 0.47+/-0.04 g(O2) m(-3) (substrate only NO(2)) for the MBR and CAS, respectively. The higher K(0) values of the CAS were attributed to mass transfer effects within the large flocs prevailing in the conventional system. In contrast, the sludge from the MBR consisted of very small flocs for which the diffusion resistance can be neglected. On the basis of these results, the implementation of mass transfer effects in activated sludge models is discussed and consequences for the operation of MBRs are highlighted.     

BSM-MBR: a benchmark simulation model to compare control and operational strategies for membrane bioreactors

A benchmark simulation model for membrane bioreactors (BSM-MBR) was developed to evaluate operational and control strategies in terms of effluent quality and operational costs. The configuration of the existing BSM1 for conventional wastewater treatment plants was adapted using reactor volumes, pumped sludge flows and membrane filtration for the water-sludge separation. The BSM1 performance criteria were extended for an MBR taking into account additional pumping requirements for permeate production and aeration requirements for membrane fouling prevention. To incorporate the effects of elevated sludge concentrations on aeration efficiency and costs a dedicated aeration model was adopted. Steady-state and dynamic simulations revealed BSM-MBR, as expected, to out-perform BSM1 for effluent quality, mainly due to complete retention of solids and improved ammonium removal from extensive aeration combined with higher biomass levels. However, this was at the expense of significantly higher operational costs. A comparison with three large-scale MBRs showed BSM-MBR energy costs to be realistic. The membrane aeration costs for the open loop simulations were rather high, attributed to non-optimization of BSM-MBR. As proof of concept two closed loop simulations were run to demonstrate the usefulness of BSM-MBR for identifying control strategies to lower operational costs without compromising effluent quality.