Application of radiant cooling as a passive cooling option in hot humid climate

In hot and humid region, air-conditioning is increasingly used to attain thermal comfort. Air-conditioning is highly energy intensive and it is desirable to develop alternative low-energy means to achieve comfort. In a previous experimental investigation using a room equipped with radiant cooling panel, it was found that cooling water kept to 25 °C could be used to attain thermal comfort under some situations, while water at such temperature would not cause condensation of moisture from air on the panel. This paper reports results of a series of whole-year simulations using TRNSYS computer code on applications of radiant cooling to a room model that represents the actual experimental room. Admitting the inability of radiant cooling to accept latent load, chilled water at 10 °C was supplied to cooling coil to precool ventilation air while water cooled by cooling tower was used for radiant cooling in daytime application. For night-time, cooling water from cooling tower supplied for radiant cooling was found to be sufficient to achieve thermal comfort. Such applications are considered to be more amenable to residential houses.     

Thermal comfort assessment and application of radiant cooling: A case study

A field assessment of thermal comfort was conducted at Mehran University of Engineering and Technology, situated in the subtropical region of Pakistan. The results show that people of the area were feeling thermally comfortable at effective temperature of 29.85 °C (operative temperature 29.3 °C). A comparison of this neutral effective temperature was made with the neutral effective temperature determined from adaptive models. It is found that the neutral effective temperature determined during this study closely match that of the adaptive model based on either indoor temperature or both indoor and outdoor temperatures. The results of thermal acceptability assessment show that more than 80% of occupants were satisfied at an effective temperature of 32.5 °C, which is 6.5 °C above the upper boundary of ASHRAE thermal comfort zone. Naturally ventilated classrooms and air-conditioned offices of the University were simulated using TRNSYS system simulation program for two cases, once when conventional air-conditioning is used for providing thermal comfort, and when comfort is achieved through radiant cooling. In the simulation, cooling tower was used to regenerate cooling water for the radiant cooling system. Energy consumption was estimated from simulation of both cases. The results show that it is possible to achieve thermal comfort for most of the time of the year through the use of radiant cooling without a risk of condensation of moisture from air on the radiant cooling surfaces. A comparison of the energy consumption estimates show that savings of 80% is possible in case thermal comfort is achieved through radiant cooling instead of conventional air-conditioning.     

Evaluation of thermal comfort using combined CFD and experimentation study in a test room equipped with a cooling ceiling

This paper reports a full-scale experimental campaign and a computational fluid dynamics (CFD) study of a radiant cooling ceiling installed in a test room, under controlled conditions. This research aims to use the results obtained from the two studies to analyze the indoor thermal comfort using the predicted mean vote (PMV). During the whole experimental tests the indoor humidity was kept at a level where the condensation risk was minimized and no condensation was detected on the chilled surface of the ceiling. Detailed experimental measurements on the air temperature distribution, surface temperature and globe temperature were realized for different cases where the cooling ceiling temperature varied from 16.9 to 18.9 °C. The boundary conditions necessary for the CFD study were obtained from the experimental data measurements. The results of the simulations were first validated with the data from the experiments and then the air velocity fields were investigated. It was found that in the ankle/feet zone the air velocity could pass 0.2 m/s but for the rest of the zones it took values less than 0.1 m/s. The obtained experimental results for different chilled ceiling temperatures showed that with a cooling ceiling the vertical temperature gradient is less than 1 °C/m, which corresponds to the standard recommendations. A comparison between globe temperature and the indoor air temperature showed a maximum difference of 0.8 °C being noticed. This paper also presents the radiosity method that was used to calculate the mean radiant temperature for different positions along different axes. The method was based on the calculation of the view factors and on the surface temperatures obtained from the experiments. PMV plots showed that the thermal comfort is achieved and is uniformly distributed within the test room.     

Design of an individually controlled system for an optimal thermal microenvironment

Individually controlled microenvironment has potential to satisfy more occupants in a space compared to a total volume uniform environment typically used at present. The performance of an individually controlled system comprising a convection-heated chair, an under-desk radiant heating panel, a floor radiant heating panel, an under-desk air terminal device supplying cool air, and a desk-mounted personalized ventilation as used and identified by 48 human subjects was studied using a thermal manikin at room temperatures of 20 °C, 22 °C and 26 °C. At a room air temperature of 20 °C, the maximum whole-body heating effect of the heating chair, the under-desk heating panel, and the floor heating panel corresponded to the effect of a room temperature increase of 5.2 °C, 2.8 °C, and 2.1 °C, respectively. The effect was 5.9 °C for the combination of the three heating options. The higher the room air temperature, the lower the heating effect of each heating option or heating combination. The maximum whole-body cooling effect of the tested system was only −0.8 °C at a room air temperature of 26 °C. The heating and cooling capacity of the individually controlled system were identified. These results, analyzed together with results obtained from human subject experiments, reveal that both the heating and the cooling capacity of the individually controlled system need to be increased in order to satisfy most occupants in practice.     

Analytical solution for heat transfer in a multilayer floor of a radiant floor system

In radiant floor systems, the distribution of the floor surface temperature, which can be used to determine the mean temperature and the lowest/highest temperature of the floor surface, is an important parameter. The mean temperature of the floor surface determines cooling/heating capacity and indoor thermal comfort. The lowest surface temperature, which considers the dew point in an indoor environment, is a crucial factor in the prevention of condensation on a floor surface. The highest surface temperature is typically considered for local thermal comfort. In this paper, an analytical solution for heat transfer in a multilayer floor structure of a radiant floor system is proposed based on the analysis of the heat transfer process of a multilayer floor, equivalent thermal resistance and separation of variables method. The corresponding formulas are derived to estimate the distribution of floor surface temperature. The calculation results are validated by experiments. The calculation and experimental results show good accordance. The absolute error between the calculation and experimental results for floor surface temperature is within 0.3°C. A method for the calculation of the dimensionless temperature of the floor surface, which can be used for radiant heating and cooling systems, is provided. Using this proposed method, the distribution of floor surface temperature and the influence of floor structure parameters on the thermal performance of floors can be estimated and analyzed.     

An experimental investigation of application of radiant cooling in hot humid climate

This paper reports an experimental and simulation study of application of radiant cooling using natural air for ventilation under hot and humid climate of Thailand. To avoid condensation of moisture on the cooling panel, the temperature of water supplied to the panel was limited to 24 °C. This led to the expectation that the low heat reception capacity of the panel would limit its use only to situations when loads were low. Experiments were conducted in an experimental room over the hot and dry period of March, the humid period of May, and the cool period of December. The results generally confirm the good potential for application of radiant cooling. However, the room was served by radiant panels with a total area of 7.5 m². Its capacity was grossly inadequate during the hot period, even for night time application only. A special configuration was devised to achieve thermal comfort for the area served by the panel. The well-known TRNSYS program was used to simulate the use of cooling panels and conventional air-conditioning in the experimental room. Simulation results match experimental results very well. Using comfort criterion adopted by ASHRAE and International Standards Organization, results from experiments and simulation show that thermal comfort could be obtained with application of radiant cooling.     

地板辐射与置换通风空调系统运行参数

建立了基于EnergyPlus的地板辐射供冷加置换通风空调系统模型,模拟得到的室内温度和辐射地板所承担冷量与实验结果的误差小于±7%。在此模型基础上,改变送风参数和供水参数,得到置换通风供冷量、辐射地板供冷量、地板表面温度、室内空气平均温度、AUST温度等参数的变化规律。结合热舒适性模型,得到满足室内热舒适性(-0.5≤PMV≤0.5)条件下,置换通风的送风参数和辐射地板的供水参数范围,为复合系统设计和应用提供依据。     

Numerical and experimental study on the characteristics of radiant ceiling systems

ABSTRACT

Insufficient knowledge about characteristics of radiant systems has caused problems in the wider application of the radiant system, such as water condensation, bad thermal comfort, etc. In this study, key characteristics of a radiant system in terms of an inherent relationship between total heat flux and surface temperature were analysed. General models for describing such the relationship were developed and validated by elaborate experimental data. Operation limit region of the radiant system was identified and proposed by plotting key parameters in one surface, including supply water temperature, operative temperature panel surface temperature as well as total heat flux density. It was found that not all of the points within the operation limit region were suitable for practical application in order to avoid water condensation risk in cooling mode and large temperature differences in a vertical direction in heating mode. Evolved forms of operation limit regions for cooling and heating applications were put forward and their characteristics were addressed. The results reported in this paper could help manufacturers as well as engineers to better design, configure and regulate radiant systems for better product development and improved indoor thermal comfort.     

Exergetic and sustainability performance comparison of novel and conventional air cooling systems for building applications

This study presents energy and exergy analyses and sustainability assessment of one novel and three conventional types of air cooling systems for building applications. First, effectivenesses of the systems are determined using energy analysis method. Second, exergy aspects of the systems are investigated for twelve different dead state temperatures varying from −5 °C to 50 °C with a temperature interval of 5 °C. The specific exergy flows of humid air, dry air and water, exergy efficiency, and specific exergy destruction are then calculated. Sustainability index is also used to define and discuss the systems’ sustainability aspects. Finally, the results obtained here show that at the dead state temperatures of higher than 23 °C (comfort temperature), exergy efficiency and sustainability of the novel system, which is based on the novel Maisotsenko cycle (M-Cycle), is higher than those of the conventional systems. At a dead state temperature of 50 °C, novel cooling system's exergy efficiency can reach 60.329% as the maximum, while the minimum exergy efficiency of other conventional cooling systems becomes as low as 35.866%, respectively.     

A combined low temperature water heating system consisting of radiators and floor heating

Space heating load is decreasing in modern Finnish apartments due to lower U-values of the construction, tight envelopes and heat recovery from exhaust ventilation air. This makes it possible to develop a new combined low temperature water heating system with nominal supply/return water temperatures of 45 °C/35 °C. Such a system includes radiators in rooms and floor heating in bathrooms.In this study, the performance of an apartment building is determined by using dynamic simulation. The simulation results for the combined low temperature water heating system are compared with those for three conventional radiator and floor heating systems. The results show that the combined low temperature water heating system performs well and is able to maintain the zones within the required temperature levels. The thermal comfort analysis indicates that the drifts and ramps in operative temperature using the four studied heating systems are within the limits of Ashrae Standard 55-2004.Temperature measurements in a test room are carried out to find the vertical difference of air temperature using two methods: radiator heating and floor heating. These measurements indicate that there is only a small vertical temperature difference that would not produce any significant thermal discomfort.     

辐射供冷空调结露问题的研究现状及其对策

辐射供冷空调具有良好的热舒适度、改善室内空气品质、节能等优点。但在热湿地区,由于辐射板表面容易结露,使得它在市场上的应用受到极大限制。本文通过对辐射供冷空调系统结露问题研究现状的总结,提出了一种"疏导结露"的辐射板模型,为辐射供冷空调系统结露问题的研究提供了新思路。     

Numerical simulation of radiant floor cooling system: The effects of thermal resistance of pipe and water velocity on the performance

Using the existing floor heating system, the radiant floor cooling system can be used as an alternative to the conventional all-air cooling systems. In this paper, a numerical model for the radiant floor cooling system is built using finite volume method. The objective of this study is to research the effects of the thermal resistance of pipe and water velocity on the performance of the radiant floor cooling system. In order to provide better heat transfer simulation in the pipe, composite grids are used in the model. The numerical floor surface temperature and the heat flux are in agreement with the measured results. The results illustrate that the pipe has effect on the performance of the radiant floor cooling system when the thermal conductivity of the pipe is low. However, the effect of the water velocity on the performance of the cooling system is not great. The model is helpful to calculate and design such kind of radiant floor cooling systems.     

地板辐射供冷系统分析

本文介绍了地板辐射供冷系统的室内外设计参数选取和负荷计算方法,通过采用CFD数值模拟的方法,分析了辐射供冷地板系统在不同的室内设计温湿度及冷水温度条件下的供冷量,冷损失量及表面温度等。应用该方法可以建立系统设计查找表格为地板辐射供冷系统设计提供基础数据。本文也给出了埋管辐射地板的系统布置方式及设计流程等。     

浅析太原市地板辐射供冷的应用

通过对太原市夏季室内空气温度和相对湿度的调查,结合地板辐射供冷系统的节能、舒适等特点,对太原市采用地板辐射供冷的可行性进行了分析,得出了地板辐射供冷用于太原市居住建筑夏季降温理论上可行的结论。     

Economic benefits of optimal control for water-cooled chiller systems serving hotels in a subtropical climate

A water-cooled chiller system in an air-conditioned hotel can take up about one-quarter of the total electricity consumption and considerable amounts of water in the heat rejection process. This paper evaluates operating cost savings of a chiller system integrated with optimal control of cooling towers and condenser water pumps. A sophisticated chiller system model was used to ascertain how different control methods influence the annual electricity and water consumption of chillers operating for the cooling load profile of a reference hotel. It is estimated that applying load-based speed control to the cooling tower fans and condenser water pumps could reduce the annual system electricity use by 8.6% and operating cost by 9.9% relative to the equivalent system using constant speed fans and pumps with a fixed set point of 29.4 °C for cooling water temperature control. The ways to implement this advanced control for system optimization are discussed.     

无保温楼板辐射供冷系统热过程的研究

楼板辐射供冷是一种舒适度很高的新型空调技术：楼板内若不设保温层，天棚和地板均成为冷辐射表面向房间供冷：系统的供冷能力和楼板上下表面温度是空调供冷系统运行和调节的关键参数，研究它们与影响因素之间的关系是十分重要的。本文建立了无保温楼板辐射供冷系统的物理模型和数学模型，并对控制方程进行数值模拟，给出了系统供冷能力和楼板上下表面温度和诸多影响因素之间的关系。研究结果显示：冷水温度越低，天棚和地板的表面温度越低，系统提高的冷量越大；天棚表面温度略大于地板表面温度；随着冷水温度的升高，天棚和地板之间的温度差异将减小，房间的舒适性好；地板辐射换热量远大于对流换热量，天棚辐射换热量略大于对流换热量；天棚提供给房间的冷量大于地板提供的冷量。且冷水温度越低，相差越大；管子埋深越大，天棚和地板表面温度越大，系统供冷量越小，但差别不显著；埋管间距越大，天棚和地板表面温度越大，系统供冷量越小；埋管管径越大，天棚和地板温度越小，系统供冷量越大，但差异不显著。研究结果可为实际工程的设计、运行参数的选择和系统的可行性分析提供依据和指导。     

Experimental study on a residential temperature-humidity separate control air-conditioner

According to the temperature and moisture characteristics and current problems experienced in the Yangtze River Area, a temperature-humidity separate control air conditioner was developed. This unit can remove indoor sensible heat and latent heat load separately, and adjust indoor temperature and humidity respectively, thus improve indoor comfort and reduce energy consumption. The air-conditioner consists of an air cooling evaporator and a water cooling evaporator. Orthogonal experiments were designed to study the influence of outdoor temperature, indoor temperature, indoor humidity, compressor frequency, and refrigerant distribution ratio in air cooling evaporator (RDRAE) on the unit performance. The results showed that the dehumidification capacity ranged from 0 to 4.02 kg/h; the EER ranged from 2.71 to 4.57; the cooling capacity ranged from 6822 to 13,080 W. The results can help to make the control logic of the unit, and be used as the basis of energy consumption calculation. Units with temperature and humidity separate control could save about 15.6% of the cooling energy consumption against traditional residential air-conditioner, and 47.8% against the traditional residential air-conditioner that could control both indoor temperature and humidity.     

Performance of temperature and humidity independent control air-conditioning system in an office building

The temperature and humidity independent control (THIC) system, which controls indoor temperature and moisture separately, may be an attractive alternative to existing conventional HVAC systems for its prominent improvement on the overall system performance and utilization of low grade energy resources. In order to verify the effectiveness of THIC system, a pilot project has been implemented in an office building in Shenzhen, China. In the system, liquid desiccant fresh air handling units driven by heat pumps are utilized to remove the entire latent load of outdoor air supplied for the whole building, and chilled water at the temperature of 17.5 °C from chiller is pumped and distributed into dry fan coil units and radiant panels to control indoor temperature. This paper presents the results of field test of the system, which shows that the system can provide a comfortable indoor environment even in very hot and humid weather. The COP of the entire THIC system can reach 4.0. According to the energy usage data recorded from the year 2009, the energy consumption of the THIC system in the tested office building was 32.2 kWh/(m² yr), which demonstrates magnificent energy-saving potential compared with the conventional air-conditioning system (around 49 kWh/(m² yr)).     

Development of a radiant heating and cooling model for building energy simulation software

Efficient radiant heating and cooling systems are promising technologies in slashing energy bills and improving occupant thermal comfort in buildings with low-energy demands such as houses and residential buildings. However, the thermal performance of radiant systems in buildings has not been fully understood and accounted for in currently available building energy simulation software. The challenging tasks to improve the applicability of radiant systems are the development of an accurate prediction model and its integration in the energy simulation software. This paper addresses the development of a semi-analytical model for radiant heating and cooling systems for integration in energy simulation software that use the one-dimensional numerical modeling to calculate the heat transfer within the building construction assemblies. The model combines the one-dimensional numerical model of the energy simulation software with a two-dimensional analytical model. The advantage of this model over the one-dimensional one is that it accurately predict the contact surface temperature of the circuit-tubing and the adjacent medium, required to compute the boiler/chiller power, and the minimum and maximum ceiling/floor temperatures, required for moisture condensation (ceiling cooling systems), thermal comfort (heating floor systems) and controls. The model predictions for slab-on-grade heating systems compared very well with the results from a full two-dimensional numerical model.     

Application of passive cooling systems in the hot and humid climate: The case study of solar chimney and wetted roof in Thailand

The thermal performance of two passive cooling systems under hot and humid climate condition is experimentally investigated. The experimental results were obtained from a test cell and a controlled cell with identical walls but different roof configurations. The passive cooling systems applied to the test cell are solar chimney and water spraying on roof. The experimental results obtained from the test cell are compared with the closed and no passive cooling controlled cell. In addition, the significant of solar-induced ventilation by using a solar chimney is realized by utilizing a wind shield to reduce the effect of wind-induced ventilation resulting in low measured air velocities to the solar chimney and low computed value of coefficient of discharge. The derived coefficient of discharge of 0.4 is used to compute Air Changes rates per Hour (ACH). The ACHs with application of solar chimney solely are found to be in the range of 0.16–1.98. The studies of air temperature differences between the room and the solar chimney suggest amount of air flow rates for different periods in a year. The derived relationships show that the air flow rate during February–March is higher than during June–October by 16.7–53.7%. The experimental results show that application of the solar chimney in the test cell could maintain the room temperature at 31.0–36.5 °C, accounting for 1.0–3.5 °C lower than the ambient air and 1.0–1.3 °C lower than the controlled cell. However, to make the test cell's room temperature much lower than the ambient temperature and increase the flow rate of air due to the buoyancy, the application of water spraying on roof is recommended together with solar chimney. The application of the two systems in the hot and humid climate are discovered to sustain the room temperature of the test cell to be lower than the ambient air by 2.0–6.2 °C and lower than the controlled cell by 1.4–3.0 °C.