Effect of Wall Charge on Striation in Plasma Display Cells

Different configurations and driving voltages have been employed to investigate the effect of the wall charge on the striations in macroscopic plasma display panel （PDP） cells. The experimental results show that a discharge channel near the dielectric layer is indispensable to striation occurring in the anode area during a discharge, while the pre-accumulated charge on the dielectric layer and the surface state are not important. The origin of the striation is related only to the physical process in the cell. The dielectric layer acts as a charge collector during a PDP discharge.     

Investigation of Anode Striation in 34＂ VGA Shadow Mask PDP

A macro-cell was used to study the phenomenon of anode striation on a 34 VGA Shadow Mask Plasma Display Panel （SMPDP）. The breakdown process in the sustaining period of the macro-cell was taken by an Intensified Charge Coupled Device（ICCD） with narrow band filters. The mechanism of formation and evolution of the anode striation on SMPDP were investigated. The influence of the width of the electrode, the sustaining voltage, sustaining frequency and the voltage of the shadow mask on the anode striation was also studied. The results showed that the width of the electrodes, the sustaining voltage and frequency had a strong influence on the anode striation. The voltage of the shadow mask, however, hardly affected the anode striation, the firing voltage or the sustaining voltage.     

Experimental Study of Diagnosis Neutral Beam for HT-7 Tokamak

Parametrical effect on plasma discharge and beam extraction in the diagnosis neutral beam （DNB） system for HT-7 tokamak was studied experimentally. Useful results with an improved beam quality were obtained.     

Inter-Calibration Between Plasma Instruments Onboard DEMETER

The in-situ measurements of the ionospheric plasma that we use come from two instruments of the scientific payload of the satellite DEMETER; the plasma analyser IAP （Instrument d＇analyse du plasma） and the Langmuir probe ISL （Instrument Sonde de Langmuir）. DEMETER is a micro-satellite realized by the CNES（Centre National d＇Etudes Spatiales, France） with a principal objective to seek a possible influence of the seismic activity on the electromagnetic waves in the ionosphere and on the ionospheric plasma. The satellite was placed on June 29, 2004, in a circular and quasi helio-synchronous orbit at -710 km altitude. The experiments function primarily at mid-latitudes （from ＋60° to -60°）. The IAP data were analysed to deduce the ion population （densities of the dominant ions, i.e. generally O^＋, H^＋ and He^＋） therefore the total ion density. The use of data IAP thus requires some precaution to make sure that the electric equilibrium conditions of the satellite, such as the satellite potential （Фsat）, are obtained during the treatment of routine, does not induce an error of measurement. When this potential is negative, the minority light ions H^＋ and He^＋ can be measured in a reliable way when their proportion is above 3% to 5% of that of O^＋. The critical limitation is： under certain conditions, the satellite potential becomes positive and reach a value about -0.5 V so that it becomes impossible to measure H^＋ ions. This is likely to involve a significant error on the composition and the density of the plasma. Therefore we carried out a calibration to estimate the missing density. The ISL experiment （Langmuir probe） provided the collected current/polarized tension characteristics of a cylindrical probe from which both electron density Ne and temperature Te were obtained. In some situations it is necessary to examine the accuracy of the electron density using another technique, for instance the high frequency （HF） spectrogram, provided by ICE （instrument champ     

Competition between fusion-evaporation and multifragmentation in central collisions in 58Ni＋4SCa at 25A MeV

The experimental data concerning the 58Ni＋48Ca reaction at Elab（Ni）=25A MeV, collected by using the CHIMERA 4n device, have been analyzed in order to investigate the competition among different reaction mechanisms for central collisions in the Fermi energy domain. As a main criterion for centrality selection we have chosen the flow angle （Snow） method, making an event-by-event analysis that considers the shape of events, as it is determined by the eigenvectors of the experimental kinetic-energy tensor. For the selected central events （8~ow〉60~） some global variables, good to characterize the pattern of central collisions have been constructed. The main features of the reaction products were explored by using different constraints on some of the relevant observables, like mass and velocity distributions and their correlations. Much emphasis was devoted, for central collisions, to the competition between fusion-evaporation processes with subsequent identification of a heavy residue and a possible multifragmentation mechanism of a well defined （if any） transient nuclear system. Dynamical evolution of the system and pre-equilibrium emission were taken into account by simulating the reactions in the framework of transport theories. Different approaches have been envisaged （dynamical stochastic BNV calculations ＋ sequential SIMON code, QMD, CoMD, etc.）. Preliminary comparison of the experimental data with BNV calculations shows reasonable agreement with the assumption of sequential multifragmentation emission in the mass region of IMFs close to the heavy residues. Possible deviations from sequential processes were found for those IMFs in the region of masses intermediate between the mass of heavy residues and the mass of light IMFs. Further simulations are in progress. The experimental analysis will be enriched also by information obtained inspecting the IMF-IMF correlation function, in order to elucidated the nature of space-time decay property of the emitting source associated with events having the largest IMF multiplicity.     

Polymer Surface Treatment by Atmospheric Pressure Low Temperature Surface Discharge Plasma： Its Characteristics and Comparison with Low Pressure Oxygen Plasma Treatment

The polymer treatment with a low-temperature plasma jet generated on the atmospheric pressure surface discharge （SD） plasma is performed. The change of the surface property over time, in comparison with low pressure oxygen （O2） plasma treatment, is examined. As one compares the treatment by atmospheric pressure plasma to that by the low pressure O2 plasma of PS （polystyrene） the treatment effects were almost in complete agreement. However, when the atmospheric pressure plasma was used for PP（polypropylene）, it produced remarkable hydrophilic effects.     

SiOx Ink-Repellent Layer Deposited by Radio Frequency（RF） Plasmas in Continuous Wave and Pulse Mode

Low surface energy layers, proposed application for non-water printing in computer to plate （CTP） technology, are deposited in both continuous wave and pulse radio frequency （13.56 MHz） plasma with hexamethyldisiloxane （HMDSO） as precursor. It is found that the plasma mode dominates the polymer growth rate and the surface composition. Derived from the spectra of X-ruy photoelectron spectroscopy （XPS） and combined with printable test it is concluded that concentration of Si in coatings plays an important role for the ink printability and the ink does not adhere on the surface with high silicon concentration.     

Influence of Long-Term Plasma Irradiation on Metallic First Mirrors in HT-7 Tokamak

The first mirror （FM） samples made of polycrystal （PC） stainless steel （SS）, molybdenum （Mo） and tungsten （W） were mounted at different locations in HT-7 tokamak to investigate the surface modifications caused by erosion and deposition. The optical transmission characteristics of first mirror samples were measured by a spectrophotometer. It was found that different irradiation environment had different influences on the first mirror surfaces, especially with wave antenna nearby. In addition, the erosion made the reflectivity of FM degrade to some extents as a whole. But the deposition on the mirror influences more than erosion does. Comparing the mirrors of SS, W and Mo, irradiated in the same environment, the W-mirror had the least changes in reflectivity with regularity, while the SS-mirror had most serious changes.     

The Solubility of Natural Cellulose After DBD Plasma Treatment

Natural cellulose was treated by an atmospheidc DBD plasma. The solubility of cellulose in a diluted alkaline solution after the plasma treatment was investigated. The properties were characterized by X-ray photoelectron spectroscopy （XPS）, Fourier-transform infrared spectroscopy （FTIR） and scanning electron microscopy （SEM）. The results indicated that the surface of cellulose treated by the argon DBD plasma was significantly etched, and the relevant force of hydrogen bonding was decreased. This might be the essential reason for the solubility improvement of natural cellulose in the diluted alkaline solution. Through a comparison of two discharge modes, the atmospheric DBD plasma gun and the parallel plate capacitively coupled DBD plasma, it was found that the atmospheric DBD plasma gun was more effective in fragmentizing the cellulose due to its production of a high energy plasma based on its special structure.     

Surface Modification of Fluororubber Using Atmospheric Pressure Dielectric Barrier Discharge （DBD）

Fluoride rubber F2311 film, an alternating copolymer of CF2-CFC1 （CTFE） and CH2-CF2 （VF2） components, was treated by atmospheric pressure dielectric barrier discharge （DBD） in air. The surface structure, topography and surface chemistry of the treated F2311 films were characterized by contact angle measurement, atomic force microscopy （AFM）, and X-ray photoelectron spectroscopy （XPS）, respectively. The experimental results showed that a short time air plasma treatment led to morphological, wettability and chemical changes in the F2311 films. The surface hydrophilicity increased greatly after the plasma treatment, the static water contact angle decreased from 98.6° to 32°, and oxygen containing groups （C=O, O-C=O, etc. ） were introduced. Atomic force microscopy revealed that plasma produced by DBD etched F2311 films obviously. The roughness of the samples increased remarkably with the formation of peaks and valleys on the treated surfaces. The increased surface wettability may be correlated with both the introduction of hydrophilic groups due to air plasma oxidation of the surface and the change in surface morphology etched by DBD.     

Performance of Dielectric Barrier Discharge Reactors on Elemental Mercury Oxidation in the Coal-Fired Flue Gas

The oxidation of elemental mercury （Hg~） by dielectric barrier discharge reactors was studied at room temperature, where concentric cylinder discharge reactor （CCDR） and surface discharge plasma reactor （SDPR） were employed. The parameters （e.g. Hg^0 oxidation efficiency, energy constant, energy yield, energy consumption, and O3 concentration） were discussed. From comparison of the two reactors, higher Hg^0 oxidation efficiency and energy constant in the SDPR system were obtained by using lower specific energy density. At the same applied voltage, energy yield in the SDPR system was larger than that in the CCDR system, and energy consumption in the SDPR system was much less. Additionally, more 03 was generated in the SDPR system. The experimental results showed that 98% of Hg^0 oxidation efficiency, 0.6 J·L^-1 of energy constant, 13.7 μg·J^-1 of energy yield, 15.1 eV·molecule^-1 of energy consumption, and 12.7 μg·J^-1 of O3 concentration were achieved in the SDPR system. The study reveals an alternative and economical technology for Hg^0 oxidation in the coal-fired flue gas.     

Plasma Limiter Based on Surface Wave Plasma Excited by Microwave

A novel plasma limiter, in which the plasma is excited by surface wave, is presented. The breakdown time of some gases filled in the limiter were calculated as a function of gas pres- sure, ionization degree and density of seed electrons under low pressure （0.01 -1 Torr） and high pressure （10 -1000 Torr） cases. The results show that the limiter filled with Xe with a pressure of 0.9 Torr, seed electron density of 10^16 m^-3, and ionization degree of 10^-4, has a breakdown time of approximate 19.6 ns.     

Improving Hydrophobicity of Glass Surface Using Dielectric Barrier Discharge Treatment in Atmospheric Air

Non-thermal plasmas under atmospheric pressure are of great interest in industrial applications, especially in material surface treatment. In this paper, the treatment of a glass surface for improving hydrophobicity using the non-thermal plasma generated by dielectric barrier discharge （DBD） at atmospheric pressure in ambient air is conducted, and the surface properties of the glass before and after the DBD treatment are studied by using contact angle measurement, surface resistance measurement and wet flashover voltage tests. The effects of the applied voltage and time duration of DBD on the surface modification are studied, and the optimal conditions for the treatment are obtained. It is found that a layer of hydrophobic coating is formed on the glass surface after spraying a thin layer of silicone oil and undergoing the DBD treatment, and the improvement of hydrophobicity depends on DBD voltage and treating time. It seems that there exists an optimum treating time for a certain applied voltage of DBD during the surface treatment, The test results of thermal aging and chemical aging show that the hydrophobic layer has quite stable characteristics. The interaction mechanism between the DBD plasma and the glass surface is discussed. It is concluded that CHa and large molecule radicals can react with the radicals in the glass surface to replace OH, and the hydrophobicity of the glass surface is improved accordingly.     

Study on the Generation Characteristics of Dielectric Barrier Discharge Plasmas on Water Surface简

A new contact glow discharge electrode employed in this study. Because of the strong field the electrode and the water surface, glow discharge on the surface of water was designed and strength in the small air gap formed by plasmas were generated and used to treat waste water. The electric field distribution of the designed electrode model was simulated by MAXWELL 3D~ simulation software, and the discharge parameters were measured. Through a series of experiments, we investigated the impact of optimal designs, such as the dielectric of the electrode, immersion depths, and curvature radii of the electrode on the generation characteristics of plasmas. In addition, we designed an equipotential multi-electrode configuration to treat a Methyl Violet solution and observe the discoloration effect. The experimental and simulation results indicate that the designed electrodes can realize glow discharge with a relative low voltage, and the generated plasmas covered a large area and were in stable state. The efficiency of water treatment is improved and optimized with the designed electrodes.     

Uniformity of Plasma Density and Film Thickness of Coatings Deposited Inside a Cylindrical Tribe by Radio Frequency Sputtering

Plasma surface modification of the inner wall of a slender tube is quite difficult to achieve using conventional means. In the work described here, an inner coaxial radio frequency （RF） copper electrode is utilized to produce the plasma and also acts as the sputtered target to deposit copper films in a tube. The influence of RF power, gas pressure, and bias voltage on the distribution of plasma density and the uniformity of film thickness is investigated. The experimental results show that the plasma density is higher at the two ends and lower in the middle of the tube. A higher RF power and pressure as well as larger tube bias lead to a higher plasma density. Changes in the discharge parameter only affect the plasma density uniformity slightly. The variation in the film thickness is consistent with that of the plasma density along the tube axis for different RF power and pressure. Although the plasma density increases with higher tube biases, there is an optimal bias to obtain the highest deposition rate. It can be attributed to the reduction in self-sputtering of the copper electrode and re-sputtering effects of the deposited film at higher tube biases.     

Effects of Finite Aspect Ratio and Noncircular Plasma Flux Surface on Electron Temperature Gradient Driven Modesd

A gyrokinetic model with integral eigenmode equations is developed based on the local equilibrium of shaped tokamak plasmas. Effects of main geometric parameters （finite aspect ratio, elongation, triangularity, and Shafranov shift gradient） on the electrostatic electron temper- ature gradient （ETG） driven modes are investigated numerically. It is found that the finite aspect ratio has a general stabilizing effect, while the elongation can be either stabilizing or destabilizing, depending on the poloidal wavelength of the mode and other parameters. It is shown that a low aspect ratio enhances the stabilizing effect of elongation, and weakens its destabilizing effect as well.     

Analysis and Optimization of Stability of CAS-LIBB Single Ion Microbeam

Single ion microbeam is the most advanced technology which can emit a single ion for precise localization. A single-ion microbeam facility has been constructed at the Key Laboratory of Ion Beam Bioengineering （LIBB）, Chinese Academy of Sciences （CAS）, with a spatial resolutions of about 5 μm. Based on CAS-LIBB microbeam, three key elements affecting the quality of the system are assessed： the size of beam spot, the energy range and the counting accuracy of implanting ions. Various contributions to the ion beam stability, including the ion source, the terminal voltage of electrostatic accelerator and the components in beam pipeline, are discussed. Analysis shows that the improvement of terminal voltage stability is the most important issue for future optimization of CAS-LIBB facility. Some preliminary investigations and project aimed at optimization and development are proposed as well.     

Heat Transfer Analysis of Two Kinds of Mechanically Jointed GBST1308/CuCrZr Plasma Facing Components of EAST

Doped graphite GBST1308, mechanically jointed to CuCrZr alloys, will be applied on EAST superconducting as plasma facing material （PFM）. Two joint structures called joint-1 and joint-2 were evaluated by means of thermal response tests using electron beam facility. The experimental results showed that the temperature differences of two joints were not significant, and the maximum surface temperature was about 1055℃ at a load of 4 MW/m^2, which had a good agreement with the simulated results by ANSYS code. The results indicated that the doped graphite GBST1308/CuCrZr mock-up can withstand heat flux deposition of 4 MW/m^2 except at the screw-fastened region, and joint-2 could be more suitable to higher heat flux region such as divertor target. But under the higher heat flux, both joints are unacceptable, an advanced PFM and its integration with the heat sink have to be developed, for example, vacuum plasma spraying tungsten coatings on the CuCrZr might be a good choice.     

Bioeffects of Low Energy Ion Beam Implantation： DNA Damage, Mutation and Gene Transter

Low-energy ion beam implantation （10 - 200 keV） has been proved to have a wide range of biological effects and is broadly used in the breeding of crops and micro-organisms.To understand its mechanisms better and facilitate its applications, the developments in the bioeffects of low energy ion beam implantation in the past twenty years are summarized in this paper.     

Structure and Mechanical Properties of CrTiAlN/TiAlN Composite Coatings Deposited by Multi-Arc Ion Plating

CrTiAlN/TiAlN composite coatings were deposited on cemented carbide by using a home-made industrial scale multi-arc ion plating system. The samples were studied by X-ray diffraction, scanning electron microscopy （SEM）, microhardness and ball-on-disk testing. The properties of the CrTiAlN/TiAlN coatings were significantly influenced by the microstructure and the deposition time ratio of TiAlN over CrTiAlN layers. With the increase of deposition time ratio, the microhardness of CrTiAlN/TiAlN increased from 28.6 GPa to 37.5 GPa, much higher than that of CrTiAlN coatings. The friction coefficients of the CrTiAlN/TiAlN coatings were higher than those of CrTiAlN coatings against a cemented carbide ball. The microhardness of the CrTiAlN/TiAlN coatings was changed after annealing at 800 ℃, and the friction coefficients of the annealed coatings were increased against the cemented carbide ball.