酶制剂的添加对早籼稻谷生料发酵生产酒精的影响

对早籼稻谷生料发酵生产酒精进行了研究。结果表明：淀粉酶、纤维素酶、酸性蛋白酶、果胶酶的添加对酒精发酵没有明显效果。糖化酶最佳添加量为225U／g原料，最佳料液比为1：3．5，300℃120h，酒精度达9．0％(v／v)，残总糖为1．20％，淀粉出酒率达51．28％。     

木瓜果酒加工工艺的研究

木瓜果实富含有机酸、皂甙、维生素、胡萝卜素、氨基酸、果胶、黄酮类和钾、镁、钙、锌、铁、锰、磷等多种微量元素和营养物质，具有极高的食用和营养保健价值。果实破碎时加入0．1％果胶酶和按100mg/kg加入2％偏重亚硫酸钠溶液；添加蔗糖调整果汁含糖量为20％～22％，加柠檬酸调整总酸在0．6～0．8g／100mL；主发酵接种量为5％，18～22℃发酵3～4d，发酵至醪液中残糖1．0％以下，酒精度为9．5％-10．0％(v／v)时结束；后酵温度10℃，时间2～3周，至醪液残糖含量降至0．1％以下完毕。     

早籼稻谷生料发酵生产酒精的工艺研究

摘要：在发酵液中添加钙、镁、锌离子可以提高淀粉出酒率，使发酵液中的残总糖明显下降。实验表明，利用早籼稻谷生料发酵生产酒精，最佳发酵温度为32℃，最佳pH为4，最佳发酵时间为120h，在最佳条件下发酵，酒分达到9．3％(v／v)，残总糖为1．08％，淀粉出酒率为53．64％。     

安琪耐高温酿酒高活性干酵母在酒精浓醪发酵中的应用

使用安琪耐高温酿酒高活性于酵母，以玉米为原料生产酒精，通过在发酵过程中添加复合酶，采用边糖化边发酵工艺，从三角瓶小试，到5t罐中试，取得了一定效果，残还原糖为0．21％，酒分达到13．6％(v／v)。同时证明了在稀醪条件下适当提高发酵温度可加快酵母的产酒，但在浓醪情况下，提高温度会增加乙醇对酵母的毒性，导致出酒率下降。     

新型大米发酵饮料的研制

以大米为主要原料，经蒸煮糊化、接种根霉、糖化、稀释、加入牛奶，以嗜热链球菌和保加利亚乳杆菌的混合菌剂进行乳酸发酵，再加苹果汁、糖、酸等调配成饮料。通过正交试验得出其最佳工艺参数为：根霉菌剂接种量4％（v／w），大米糖化醪加纯净水稀释1．5倍，添加鲜牛奶40％（v／v），接种乳酸菌混合菌剂5％（v／v），42℃-44℃发酵14h；添加苹果汁15％（v／v），白砂糖5％（w／v），柠檬酸0．125％（w／v），复配稳定剂0．15％（w／v），用高速剪切混合乳化机5000r／min乳化10min，成品经115℃灭菌15min，符合相应产品的国家食品卫生质量要求。     

糖化酶对高粱Lager啤酒麦汁组成和糖酵解的影响

我们进行了一个置信度P〈0．05的三因子实验，利用大麦麦芽（BM）或高梁芽（SM），精选玉米（MZ）或腊质高梁（WXSOR）粉粒为辅料，添加或不添加糖化酶（AMG）生产Lager啤酒，研究其144h发酵过程中糖酵解和乙醇生成情况。在BM麦汁中，葡萄糖、麦芽糖、麦芽三糖分别占总可发酵糖的20％，68％和13％，而这个比例在SM麦汁中则分别为35％，48％和17％。添加AMG后，麦汁中葡萄糖含量从9．3g／L增加到24．5g／L，总可发酵性糖含量用g葡萄糖／L表示，从59．2g／L增加到72．6g／L。和BM麦汁相比，SM麦汁的葡萄糖含量约高50％，而初始麦芽糖则要低40％左右。用WXSOR或MZ作酿造辅料，生产的麦汁和啤酒具有相似的特性。AMG的添加使麦汁中葡萄糖量增加2．5倍以上，并使可发酵性糖量增加23％以上。线性回归分析表明发酵过程中可发酵性糖的消耗符合一级反应方程。葡萄糖、麦芽糖和麦芽三糖消耗50％的时间分别为49h，128h和125h，这清楚地表明酵母优先利用葡萄糖。和不添加AMG的麦汁相比，添加AMG麦汁中的麦芽糖和麦芽三糖的消耗速度分别加快和变慢了。发酵终了，BM啤酒的乙醇含量（5．1％，v／v）比SM啤酒（3．9％，v／v）要高。在添加AMG的啤酒生产中，用BM还是用SM及添加MZ辅料在最终的乙醇浓度上并无明显区别。研究结果表明，AMG可以降低糊精含量，增加初始葡萄糖量和总可发酵性糖量，特别是在利用SM为原料的时候，该现象更为明显。     

新型大米发酵饮料的研制

以大米为主要原料，经蒸煮糊化、接种根霉、糖化、稀释、加入牛奶，以嗜热链球菌和保加利亚乳杆菌的混合菌剂进行乳酸发酵，再加苹果汁、糖、酸等调配成饮料。通过正交试验得出其最佳工艺参数为：根霉菌剂接种量4％（v／w），大米糖化醪加纯净水稀释1．5倍，添加鲜牛奶40％（v／v），接种乳酸菌混合菌剂5％（v／v），42℃-44℃发酵14h；添加苹果汁15％（v／v），白砂糖5％（w／v），柠檬酸0．125％（w／v），复配稳定剂0．15％（w／v），用高速剪切混合乳化机5000r／min乳化10min，成品经115℃灭菌15min，符合相应产品的国家食品卫生质量要求。     

超级酒酵母在浓醪发酵生产中的应用

采用安琪超级耐高温酿酒高活性干酵母(以下简称超级酒酵母)，并投资25万元对糖化系统、超级酒酵母的实际应用与预发酵罐系统、蒸馏系统进行技术改造。实现了浓醪发酵，发酵指标达到自建厂以来最高水平：酒分平均在13．4％(v／v)以上，平均残还原糖0．173％，平均残总糖1．84％。提高了生产能力，达到了节约用水、降低能耗的目的，年节约动力成本244．5万元，年创效益664．5万元。(小凡)     

甜高梁杆鲜糖汁发酵生产酒精的工业化试验

以甜高粱杆为原料利用压榨方法取得鲜糖汁,进行酒精发酵工业化试验,验证工业化生产的可行性,发酵成熟醪酒份为7．02％（V）,残总糖为0．12％,发酵率为92．8（v／v）,发酵周期为24小时。     

发酵型无花果酒酿造工艺研究

对无花果酒酿造工艺、操作要点进行了研究。结果表明：在糖浓度为20％-22％的无花果清汁中加入60mg/L～90mg／L的SO2，接入5g／L-7g／L葡萄酒活性干酵母，20℃发酵14d；可以使发酵彻底，原酒残糖量低，酒精度最高可达11．2％（v／v）；同时既可以保证酒质，也不会延长发酵时间。     

Textural Properties of Cold-set Gels Induced from Heat-denatured Whey Protein Isolates

A 9% whey protein (WP) isolate solution at pH 7.0 was heat-denatured at 80°C for 30 min. Size-exclusion HPLC showed that native WP formed soluble aggregates after heat-treatment. Additions of CaCl2 (10–40 mM), NaCl (50–400 mM) or glucono-delta-lactone (GDL, 0.4–2.0%, w/v) or hydrolysis by a protease from Bacillus licheniformis caused gelation of the denatured solution at 45°C. Textural parameters, hardness, adhesiveness, and cohesiveness of the gels so formed changed markedly with concentration of added salts or pH by added GDL. Maximum gel hardness occurred at 200 mM NaCl or pH 4.7. Increasing CaCl2 concentration continuously increased gel hardness. Generally, GDL-induced gels were harder than salt-induced gels, and much harder than the protease-induced gel.     

Occurrence of bisphenol-F-diglycidyl ether (BFDGE) in fish canned in oil

The levels of bisphenol-F-diglycidyl ether (BFDGE) were quantified as part of a European survey on the migration of residues of epoxy resins into oil from canned fish. The contents of BFDGE in cans, lids and fish collected from all 15 Member States of the European Union and Switzerland were analysed in 382 samples. Cans and lids were separately extracted with acetonitrile. The extraction from fish was carried out with hexane followed by re-extraction with acetonitrile. The analysis was performed by reverse phase HPL C with fluorescence detection. BFDGE could be detected in 12% of the fish, 24% of the cans and 18% of the lids. Only 3% of the fish contained BFDGE in concentrations considerably above 1mg/kg. In addition to the presented data, a comparison was made with the levels of BADGE (bisphenol-A-diglycidyl ether)analysed in the same products in the context of a previous study.     

Contribution of European research to risk analysis

The European Commission's, Quality of Life Research Programme, Key Action 1—Health, Food & Nutrition is mission-oriented and aims, amongst other things, at providing a healthy, safe and high-quality food supply leading to reinforced consumer confidence in the safety of European food. Its objectives also include the enhancing of the competitiveness of the European food supply. Key Action 1 is currently supporting a number of different types of European collaborative projects in the area of risk analysis. The objectives of these projects range from the development and validation of prevention strategies including the reduction of consumers risks; development and validation of new modelling approaches; harmonization of risk assessment principles, methodologies, and terminology; standardization of methods and systems used for the safety evaluation of transgenic food; providing of tools for the evaluation of human viral contamination of shellfish and quality control; new methodologies for assessing the potential of unintended effects of genetically modified (genetically modified) foods; development of a risk assessment model for Cryptosporidium parvum related to the food and water industries; to the development of a communication platform for genetically modified organism, producers, retailers, regulatory authorities and consumer groups to improve safety assessment procedures, risk management strategies and risk communication; development and validation of new methods for safety testing of transgenic food; evaluation of the safety and efficacy of iron supplementation in pregnant women; evaluation of the potential cancer-preventing activity of pro- and pre-biotic ('synbiotic') combinations in human volunteers. An overview of these projects is presented here.     

低温带皮菜籽粕微粉的不同粒级部分的功能特性

为研究低温带皮菜籽粕微粉的不同粒级部分的功能特性,以经低温脱脂的带皮菜籽粕为原料,经微粉碎后筛分成212~425μm、150~212μm和106~150μm的3个不同粒级的微粉样品,检测这些样品的吸水性、吸油性、乳化性和乳化稳定性、蛋白质体外消化率。结果表明:1 3个不同粒级的微粉样品之间的粗纤维含量存在显著差异,表明三者的结构组成成分有一定差异。23个微粉样品的乳化活性和乳化稳定性随粒度级别的减小而显著增加(P0.01)。33个微粉样品的蛋白质体外消化率随粒度级别的减小而显著增加(P0.01)。4不同粒级带皮菜籽粕微粉样品的吸水性与吸油性受其结构组成物质不同和粒度的双重影响,与粒度的相关性不明显。     

Microbiology of food taints

Fresh and processed foods are often spoilt by the presence of undesirable flavours and odours caused by microbial action. The aim of this paper is to review the current knowledge of microbiologically induced taints that occur in a wide range of foodstuffs, including meats, poultry, fish, crustaceans, milk, dairy products, fruits, vegetables, cereals and cereal products. Examples have been chosen where the compounds responsible for the taint have been identified and sufficient data obtained to demonstrate the involvement of microorganisms. However, in some cases the full identity of the causative organism may not have been elucidated. The types of microorganisms covered by this review include bacteria, fungi, yeasts, actinomycetes and cyanobacteria. Although cyanobacteria do not in general infect foods, their presence in aqueous systems and water supplies can lead to off-flavours in aquatic organisms and processed foodstuffs. Several examples of each of these processes are discussed. Wherever possible, the likely biosynthetic pathway used by the microorganism to produce the offending compound in a foodstuff is indicated.     

Analysis for organic residues from aids to polymerization used to make plastics intended for food contact

Polymers intended for food contact use have been analysed for organic residues which could be attributed to a range of substances employed as polymerization aids (e.g. initiators and catalysts). A wide range of polymers was extracted with solvents and the extracts analysed by gas chromatography-mass spectrometry (GC-MS). The overwhelming majority of substances identified were not derived from aids to polymerization but were oligomers, additives and adventitious contaminants. However, a small number of substances were identified as initiator residues. These included tetramethylsuccinonitrile (TMSN) which was observed in two polymers and it derived from recombination of two azobisisobutyronitrile (AIBN) initiator radicals. Methyl benzoate, benzoic acid, biphenyl and phenyl benzoate were detected in one poly(methyl methacrylate) sample and in two polyvinylchlorides and they are thought to be derived from benzoyl peroxide initiator. TMSN was subsequently targeted for analysis of poly-(methyl methacrylate) plastics using proton nuclear magnetic resonance spectrometry (¹     

Tests of potential functional barriers for laminated multilayer food packages. Part II: Medium molecular weight permeants

Experiments were performed to characterize the kinetics of the permeation of different medium molecular weight model permeants: bisphenol A, warfarin and anthracene, from liquid paraffin, through a surrogate potential functional barrier (25 microns-thick orientated polypropylene--OPP) into the food simulants olive oil and 3% (w/v) acetic acid. The characterization of permeation kinetics generally observed the permeation models previously reported to explain the experimental permeation results obtained for a low molecular weight group of model permeants. In general, the model permeants exhibited behaviour consistent with their relative molecular weights with respect to (a) the time taken to attain steady-state permeation into the food simulant in which they were more soluble, (b) their subsequent steady-state permeation rates, and (c) their partition between liquid paraffin and the OPP membrane.     

The development of reference materials for paralytic shellfish poisoning toxins in lyophilized mussel. I: Interlaboratory studies of methods of analysis

This paper describes the first part of a project undertaken to develop mussel reference materials for Paralytic Shellfish Poisoning (PSP) toxins. Two interlaboratory studies were undertaken to investigate the performance of the analytical methodology for several PSP toxins, in particular saxitoxin (STX) and decarbamoyl-saxitoxin (dc-STX) in lyophilized mussels, and to set criteria for the acceptance of results to be applied during the second part of the project: the certification exercise. In the first study, 18 laboratories were asked to measure STX and dc-STX in rehydrated lyophilized mussel material and to identify as many other PSP toxins as possible with a method of their choice. In the second interlaboratory study, 15 laboratories were additionally asked to determine quantitatively STX and dc-STX in rehydrated lyophilized mussel and in a saxitoxin-enriched mussel material. The first study revealed that three out of four postcolumn derivatization methods and one pre-column derivatization method sufficed in principle to determine STX and dc-STX. Most participants (13 of 18) obtained acceptable calibration curves and recoveries. Saxitoxin was hardly detected in the rehydrated lyophilized mussels and results obtained for dc-STX yielded a CV of 58% at a mass fraction of 1.86 mg/kg. Most participants (14 out of 18) identified gonyautoxin-5 (GTX-5) in a hydrolysed extract provided. The first study led to provisional criteria for linearity, recovery and separation. The second study revealed that 6 out of 15 laboratories were able to meet these criteria. Results obtained for dc-STX yielded a CV of 19% at a mass fraction of 3.49mg/kg. Results obtained for STX in the saxitoxin-enriched material yielded a CV of 19% at a mass fraction of 0.34mg/kg. Saxitoxin could not be detected in the PSP-positive material. Hydrolysis was useful to confirm the identity of GTX5 and provided indicative information about C1 and C2 toxins in the PSP-positive material. The methods used in the second interlaboratory study showed sufficiently consistent analysis results to undertake a certification exercise to assign certified values for STX and dc-STX in lyophilized mussel.     

The Ministry of Environmental Protection Issued "Feasible Technology Guidelines for Pollution Prevention and Control in Wood Pulping Process of the Paper Industry (Trial)" and Two Other Guiding Technical Documents

On December 27t＂, 2013, the Ministry of Environmenta Protection announced that, in order to implement ＂The Environmental Protection Law of the People＇ s Republic of China＂, improve the working system in environmenta protection technologies, and promote technologica advancement in pollution prevention, the Ministry of Environmental Protection sponsored the formulation of three guiding technical documents including ＂Feasible Technology Guidelines for Pollution Prevention and Contro n Wood Pulping Process of the Paper Industry （Trial）＂     

1~(st) Intelli-Tissue~ EcoEc Tissue Machine Supplied by PMP Group Successfully Put into Operation in China

正On April 29th,2014,Intelli-Tissue EcoEc tissue machine supplied by PMP Group successfully put into operation at Hebei Xuesong Paper Co.,Ltd.,this is the first such kind of paper machine of PMP Group in China.