Aeration of model gels: Rheological characteristics of gellan and agar gels

Model food sols containing gellan and agar at different solid concentrations were aerated. The rheological characteristics of the setted gels were determined. These were the compression characteristics (fracture strain/stress/energy, firmness and the total energy for compression) and the stress relaxation characteristics (extent of relaxation and relaxation time). Fracture strain of gels increased due to aeration indicating that the aerated samples exhibited a delayed fracture due to the presence of incorporated air. The extent of increase in fracture strain for aerated agar gels over the corresponding non-aerated samples is 1.7-23.1% while it is 4.3-15.1% for gellan gels. The extent of relaxation increased due to aeration while relaxation time (λ) decreased. Relaxation time for aerated agar and gellan gels is 9.6-40.7% and 19.6-37.6% lower than the non-aerated samples. At a low concentration of hydrocolloid, the effect of aeration was usually non-significant (at p ? 0.05) while prominent changes in rheological behaviour occurred at a high concentration. Aeration of food gels offered the possibility of rheological modifications to suit the consumer requirements in developing specialty fabricated gels.     

Rheological analysis of emulsion-filled gels based on high acyl gellan gum

Emulsion-filled gels are widely used in cosmetic, food, and pharmaceutical industry. As rheological properties of these systems are strongly dependent on the properties of the gelled polymer network, rheological characteristics of gels containing high and low acyl gellan gum were analyzed. Under the processing conditions low acyl emulsions were unstable, thus in the present work the influence of oil and hydrocolloid concentrations on the viscoelastic behavior of emulsion-filled gels containing high acyl gellan gum was studied. Increasing gellan concentration (from 0.1 g/100 g to 0.5 g/100 g) produced stronger gels, while oil fraction (10 g/100 g–30 g/100 g) slightly affected the elastic behavior of the emulsions reinforcing the structure and the elastic characteristics of the gellan matrix. Sauter diameter (d₃₂) was measured for all emulsions and an average value of 12 μm was obtained. Rheological data (oscillatory and creep–recovery tests) were successfully modeled to interpret the structural characteristics of the gelled emulsions. The broadened Baumgaertel–Schausberger–Winter spectrum was used to represent the linear viscoelastic behavior of the continuous phase and the emulsified system, showing that the rheological behavior of the systems was controlled by the highly structured continuous phase rather than the contribution of filler lipid droplet in the emulsion. Relaxation spectra were validated using creep–recovery experiments. Regardless of hydrocolloid concentration, creep compliance of the gel emulsions decreased compared with their respective gels, showing that the inclusion of oil droplets produced a reinforcement of the structure and the gel strength of the matrix.     

Compression resistance,sweetener's diffusion and sweetness of hydrocolloids gels

The effects of the type and concentration of two hydrocolloids—κ-carrageenan and gellan gum—and of the type and concentration of two sweeteners—sucrose and aspartame—on the gel resistance to compression, on the sweetener diffusion and on the intensity of the gel sweetness and the relationships between the gel physical properties and their perceived sweetness were studied. The gels true rupture stress increased with hydrocolloid concentration, this increase being higher for gellan gels. Gellan gels showed lower true rupture strain values, which in contrast with carrageenan gels, decreased on increasing hydrocolloid concentration. The addition of sucrose produced a bigger increase in gel strength at the higher hydrocolloid concentration. The main effect detected on the sweeteners’ diffusion constant was the higher value observed in low concentration (3 g L⁻¹) κ-carrageenan gels. Gellan gels were perceived as sweeter than κ-carrageenan gels. The decrease in sweetness due to an increase in hydrocolloid concentration was greater in gellan than in carrageenan gels. Variations in sweetener concentration, true rupture strain, and deformability modulus values explained 93% of the variability in sweetness for gels with sucrose and 94% for gels with aspartame.     

Rheological characterization and activation energy values of binary mixtures of gellan

The present study determined the flow behavior and activation energy of high (HA) and low (LA) acyl gellan dispersions (0.2%) and their mixtures as a function of preparation temperature (25 and 90 °C) and of the presence or absence of Ca²⁺ (30 mM). Heated gellan mixtures containing calcium were acidified with δ-gluconolactone to obtain gels and determine linear viscoelasticity using the Kelvin–Voigt model. The studied dispersions showed non-Newtonian shear-thinning behavior. HA dispersions (with and without Ca²⁺) showed the highest activation energy values, 88.60 and 51.18 kJ/mol. Whereas, LA dispersions showed the lowest activation energy values, 3.73 and 9.19 kJ/mol. With respect to the rheological studies, it was observed that the relationships between HA and LA gellan did not affect the recovery percentages because similar values were obtained (86.90–90.00%), and this behavior along with the mean viscosity values obtained in the gel mixtures could indicate that the hydrogen bond formation between both gellan helix (HA, LA) is possible. These results can contribute to possible industrial applications of gellans in the development of new alimentary products.     

CHARACTERIZATION OF GELLAN GELS BY UNIAXIAL COMPRESSION,STRESS RELAXATION AND CREEP 1

The rheological properties of 0.5–2.5% gellan gels were evaluated by uniaxial compression, stress relaxation and creep tests. The gel's strength was in the range of 0.1–1 kg.cm^-2 and their deformability modulus 1–6 kg.cm^-2. The asymptotic modulus determined in relaxation tests at two strains and the asymptotic creep compliance determined under two loads indicated that gellan gels have a yielding structure. The strains sustained in creep were considerably higher than the failure strain in uniaxial compression. Weight loss due to syneresis was on the order of 4–38% depending on the gum concentration, the deformation level in relaxation or the load in the creep tests.     

Gelation of gellan – A review

Gellan is an anionic extracellular bacterial polysaccharide discovered in 1978. Acyl groups present in the native polymer are removed by alkaline hydrolysis in normal commercial production, giving the charged tetrasaccharide repeating sequence: → 3)-β-d-Glcp-(1 → 4)-β-d-GlcpA-(1 → 4)-β-d-Glcp-(1 → 4)-α-l-Rhap-(1 →. Deacylated gellan converts on cooling from disordered coils to 3-fold double helices. The coil–helix transition temperature (T_m) is raised by salt in the way expected from polyelectrolyte theory: equivalent molar concentrations of different monovalent cations (Group I and Me₄N⁺) cause the same increase in T_m; there is also no selectivity between different divalent (Group II) cations, but divalent cations cause greater elevation of T_m than monovalent. Cations present as counterions to the charged groups of the polymer have the same effect as those introduced by addition of salt. Increasing polymer concentration raises T_m because of the consequent increase in concentration of the counterions, but the concentration of polymer chains themselves does not affect T_m. Gelation occurs by aggregation of double helices. Aggregation stabilises the helices to temperatures higher than those at which they form on cooling, giving thermal hysteresis between gelation and melting. Melting of aggregated and non-aggregated helices can be seen as separate thermal and rheological processes. Reduction in pH promotes aggregation and gelation by decreasing the negative charge on the polymer and thus decreasing electrostatic repulsion between the helices. Group I cations decrease repulsion by binding to the helices in specific coordination sites around the carboxylate groups of the polymer. Strength of binding increases with increasing ionic size (Li⁺ < Na⁺ < K⁺ < Rb⁺ < Cs⁺); the extent of aggregation and effectiveness in promoting gel formation increase in the same order. Me₄N⁺ cations, which cannot form coordination complexes, act solely by non-specific screening of electrostatic repulsion, and give gels only at very high concentration (above ∼0.6 M). At low concentrations of monovalent cations, ordered gellan behaves like a normal polymer solution; as salt concentration is increased there is then a region where fluid “weak gels” are formed, before the cation concentration becomes sufficient to give true, self-supporting gels. Aggregation and consequent gelation with Group II cations occurs by direct site-binding of the divalent ions between gellan double helices. High concentrations of salt or acid cause excessive aggregation, with consequent reduction in gel strength. Maximum strength with divalent cations comes at about stoichiometric equivalence to the gellan carboxylate groups. Much higher concentrations of monovalent cations are required to attain maximum gel strength. The content of divalent cations in commercial gellan is normally sufficient to give cohesive gels at polymer concentrations down to ∼0.15 wt %. Gellan gels are very brittle, and have excellent flavour release. The networks are dynamic: gellan gels release polymer chains when immersed in water and show substantial recovery from mechanical disruption or expulsion of water by slow compression. High concentrations of sugar (∼70 wt % and above) inhibit aggregation and give sparingly-crosslinked networks which vitrify on cooling. Gellan forms coupled networks with konjac glucomannan and tamarind xyloglucan, phase-separated networks with kappa carrageenan and calcium alginate, interpenetrating networks with agarose and gelling maltodextrin, and complex coacervates with gelatin under acidic conditions. Native gellan carries acetyl and l-glyceryl groups at, respectively, O(6) and O(2) of the 3-linked glucose residue in the tetrasaccharide repeat unit. The presence of these substituents does not change the overall double helix structure, but has profound effects on gelation. l-Glyceryl groups stabilise the double helix by forming additional hydrogen bonds within and between the two strands, giving higher gelation temperatures, but abolish the binding site for metal ions by changing the orientation of the adjacent glucuronate residue and its carboxyl group. The consequent loss of cation-mediated aggregation reduces gel strength and brittleness, and eliminates thermal hysteresis. Aggregation is further inhibited by acetyl groups located on the periphery of the double helix. Gellan with a high content of residual acyl groups is available commercially as “high acyl gellan”. Mixtures of high acyl and deacylated gellan form interpenetrating networks, with no double helices incorporating strands of both types. Gellan has numerous existing and potential practical applications in food, cosmetics, toiletries, pharmaceuticals and microbiology.     

STRESS RELAXATION BEHAVIOR OF MICROWAVE-VACUUM-DRIED ALGINATE GELS

Swelling of alginate polymer matrix in water involves a build up of network pressure due to an elastic extension of the polymeric matrix. When this network pressure undergoes relaxation by means of dehydration, shrinkage may take place. Three different types of wet alginate gels were prepared and dried using microwave‐vacuum‐drying technique. Dried alginate gel solids had a porous structure. To understand the stress relaxation behavior of alginate gel‐based porous solid structures, uniaxial compressive relaxation studies were performed at selected strain rates, preloads and relaxation times Experimental relaxation curves were normalized and fitted to an empirical relationship, and relaxation behavior was explained. Stress relaxation data were also fitted to another empirical model. All three types of gels had similar elastic components. At lower strain rate, all samples had more resistance to elastic deformation. Stress relaxation information of the dried gel was related to its microstructure. Type 2 gel had more stiffness than type 1 and type 3 gels. The mechanism involved in stress relaxation was entanglement coupling of larger polymer chains in covalently cross‐linked alginate gels.     

Rheological,gelling and emulsifying properties of a glycosylated and cross‐linked caseinate generated by transglutaminase

The impacts of oligochitosan glycosylation and cross‐linking on some properties of a commercial caseinate were investigated in this study. The glycosylated and cross‐linked caseinate with glucosamine content of 4.74 g kg^?1 protein was generated by transglutaminase (TGase) and oligochitosan at pH 7.5 and 37 °C, with fixed substrate molar ratio of 1:3 (acyl donor to glucosamine acceptor), caseinate content of 50 g L^?1, TGase of 10 kU kg^?1 protein and reaction time of 3 h, respectively. In comparison with the caseinate, the glycosylated and cross‐linked caseinate had decreased reactable amino groups (0.58 vs. 0.51 mol kg^?1 protein), higher apparent viscosity, decreased emulsifying activity index (about 14.5%) and statistically unchanged emulsion stability index (92.6 vs. 90.5%). Based on the mechanical spectra of the acid‐induced gels, the glycosylated and cross‐linked caseinate showed shorter gelation time (95 vs. 200 or 220 min) than the caseinate or cross‐linked caseinate. The gels prepared from the glycosylated and cross‐linked caseinate also had enhanced hardness, springiness and cohesiveness. The results indicated that TGase‐mediated oligochitosan glycosylation and cross‐linking has the potential to obtain new protein ingredients.     

Characterization of gellan/gelatin mixed solutions and gels

The physico-chemical properties of gellan/gelatin mixed solutions and gels were examined at five different ratios of gellan to gelatin (100:0 (I), 80:20 (II), 60:40 (III), 40:60 (IV), 20:80 (V)) and four different NaCl levels (0–300 mmol/l). All mixed solutions exhibited the shear-thinning behavior, which decreased with increasing gelatin proportion, temperature, and NaCl level. Synergism on G′ was observed in mixed solution III and IV depending on NaCl level. Hardness of mixed gel decreased with increasing gelatin proportion and cohesiveness increased up to the gellan to gelatin ratio of 40–60 and then decreased. For gellan dominant gels, maximum hardness and cohesiveness were observed at NaCl level of 150 mmol/l. Increasing gelatin proportion caused an increase in gel turbidity at lower NaCl levels and a decrease in gel turbidity at higher NaCl levels. In general, WHC increased with increasing gelatin proportion and decreasing NaCl level. Color holding capacity significantly increased with increasing gelatin proportion. Flavor holding capacity increased by adding gelatin and then linearly decreased with increasing gelatin proportion. Therefore, this study suggests that there is an optimum NaCl concentration and gellan to gelatin ratio to enhance the physico-chemical properties of gellan/gelatin mixed solutions and gels.     

低酰基结冷胶酸性凝胶的凝胶特性

以葡萄糖酸-δ-内酯(glucono-δ-lactone,GDL)作为酸诱导剂,制备低酰基结冷胶(low acyl gellan gum,LA)酸性凝胶,考察基体质量浓度、GDL/LA复配比例以及酸液浸泡对酸性凝胶凝胶特性的影响。研究结果表明,GDL酸化为缓慢酸化,GDL/LA复配比例越高、体系的pH值越低,酸化速率越快。基体质量浓度和GDL/LA复配比例对酸性凝胶结构影响显著,断裂应力和保水性随着GDL/LA复配比例的增大先升高后降低。基体质量浓度越高,断裂应力和不透明性越大。GDL/LA复配比例增大,断裂应变减小,不透明性增大。当酸液pH值为1时,酸液浸泡对GDL/LA复配比例为2∶1和4∶1的酸性凝胶强度无影响,但GDL/LA复配比例为1∶4、1∶2和1∶1时,凝胶强度随浸泡时间的增加而增强,酸液浸泡可以促使酸性凝胶进行结构重建。     

The effect of pH and calcium ion on rheological behaviour of β‐lactoglobulin‐basil seed gum mixed gels

Effect of pH (4.5–7.5) and Ca²⁺ (0.01–0.5 m ) on gelation of single and mixed systems of 10% β‐lactoglobulin (BLG) and 1% basil seed gum (BSG) was investigated. The gelling point of BLG and BSG gels was strongly pH‐dependent, and stiffer gels formed at higher pH. The BLG gels were formed upon heating to 90 °C and reinforced on cooling to 20 °C; however, the gelation of BSG occurred at temperatures below 70 °C. By increasing Ca²⁺ concentration, storage modulus of BLG and BSG gels were increased, although pH had a greater effect than Ca²⁺. In contrast, mixed systems showed two distinct types of behaviour: BLG gel formation and BSG network, suggesting that phase‐separated gels were formed. In addition, higher strength was obtained for BLG‐BSG mixture at higher Ca²⁺ concentration.     

Thermal stability and transition temperatures of monovalent salts of high‐acyl gellan gels

Thermogravimetry/derivative thermogravimetry (TG/DTG), rheometry and differential scanning calorimetry (DSC) were used to study the thermal stability and determine the transition temperatures of the sodium and potassium salts of high‐acyl gellan (HAG) in the presence of 0–100 mm NaCl and KCl, respectively. TG/DTG revealed the potassium gellan (KHAG) gels to be more stable than those of sodium gellan (NaHAG), regardless of external cation concentration. Rheometry and DSC showed the melting (T_m) and gelling (T_g) temperatures to increase with cation concentration. The DSC peak temperatures showed thermal hysteresis contrary to rheometry. In most cases, DSC revealed KHAG to exhibit higher T_m and T_g than NaHAG. Consequently, thermal characteristics of NaHAG and KHAG gels depend on the size of the external cation and its ability to coordinate water molecules. Cation salts of HAG exhibit significantly lower transition temperatures than the commercial preparation from which they were produced.     

Sensory quality of low-sugar orange gels with gellan, xanthan and locust bean gums

Effects of reducing the sucrose content (from 55 to 30 ^°Brix in the final product) and of the use of gellan gum or a mixture of gellan, xanthan and locust bean gums (3:1:1) on the mechanical characteristics (maximum rupture force and deformation at rupture) of orange gels prepared with 15% w/w fruit pulp, sucrose and different amounts of hydrocolloids (0.25, 0.4, 0.55 and 0.7% w/w) were studied by uniaxial compression. The concentration of aspartame needed to compensate for sweetness loss was determined by a paired-comparison constant-stimulus method. Sensory characteristics (texture, appearance and flavour) of low-sugar orange gels (30 ^°Brix) with 0.5% w/w aspartame and different amounts (0.55 and 0.7% w/w) of gellan or the mixture of gums were analysed by the free choice profile method in comparison with the high-sucrose reference material (55 ^°Brix and 0.4% w/w gellan). Use of the mixture of gums permitted the obtention of low-sugar orange gels showing mechanical characteristics similar to those of the reference gel, though some differences in texture were perceived. The low-sugar gels were slightly lighter in colour and slightly more bitter and refreshing than the reference sample. Received: 29 November 1995/Revised version: 13 May 1996     

Rheological properties of cereal starch gels and Mesona Blumes gum mixtures

The effect of Mesona Blumes gum (MBG) was examined on steady and dynamic shear of MBG/rice starch and MBG/wheat starch gels. In addition, stress relaxation and creep tests were performed for two types of cereal starch gels. The flow curves of both MBG/starch gels exhibited pseudoplastic behavior at shear rates between 0.01 and 10 s⁻¹, and the data were fitted into the power law model (R² = 0.91–0.98). Dynamic mechanical spectrum showed that all gels were strong gels in frequency between 0.1 and 10 Hz. Stress relaxation data at different strains indicated a strain‐softening phenomenon for both gels. Data were fitted into Maxwell model (R² = 0.91–0.98). Creep curves were conducted at the shear stress 6.4 Pa within linear viscoelastic region of both MBG/starch gels. Data were fitted into Burgers model (R² = 0.91–0.98). Apparent viscosity η, storage moduli G′, equilibrium stress relaxation modulus G_e and zero apparent viscosity η₀ of MBG/rice starch gels decreased in the following order: 6/0>6/0.5>6/0.35>6/0.1 (starch/gum w/w). Whereas η, G′, G_e, and η₀ of MBG/wheat starch gels increased gradually along side the increase of MBG contents. The stress relaxation time λ of MBG/rice starch gels increased in the following order: 6/0<6/0.5<6/0.35<6/0.1 (starch/gum w/w) while λ of MBG/wheat starch gels decreased gradually with the increase of MBG level. The influence of MBG on two examined cereal starch is totally opposite.     

TEXTURE PROPERTIES OF GELLAN GELS AS AFFECTED BY TEMPERATURE

Gellan gels can be made very brittle, similar to agar gels, or very flexible, like gelatin gels. The entropy or enthalpy nature governing those gellan gel behaviors was studied by mechanical testing at temperatures varying from 2 to 62C. Both failure stress and strain for 1% low acyl and low acyl/high acyl mixed gellan gels decreased with increasing temperature, indicating that the hydrogen bonding contributed significantly to the stabilization of gellan gels in addition to the polyanion-calcium-polyanion bonding. Hydrophobic interactions were less important. The initial Young's modulus for two mixed high and low acyl gellan gels containing 2 mM Ca⁺⁺ increased with temperature from 2–42C, indicating entropy elasticity. Average molecular weight between adjacent crosslinks for these two mixed gels was larger than 10⁴. For other gels, the entropy elasticity was not a dominant mechanism for elastic force because of molecular weights between crosslinks and from the observation of negative temperature dependence of the modulus.     

Sol-gel transition temperatures of high acyl gellan with monovalent and divalent cations from rheological measurements

The sol–gel transition temperatures of 0.1–1.0% high acyl gellan (HAG) with 0–200 mM NaCl or KCl and 0–20 mM CaCl₂ or MgCl₂ were determined using rheological measurements. Transition temperatures for monovalent cations, Na⁺ and K⁺, in the range of 50–80 °C were not significantly different (p > 0.5). Absence of thermal hysteresis was the salient feature. However, thermal hysteresis (∼4.4 °C) was observed for 0.1% HAG without added salt, but disappeared on increasing HAG and counterion concentrations. Few concentrations of HAG and added monovalent and divalent cations showed thermal hysteresis not higher than 2.5 °C. Transition temperatures for divalent cations were similar to those for monovalent cations although for considerably lower concentrations of Ca²⁺ or Mg²⁺. Increasing concentrations of monovalent and divalent counterions give rise to higher transition temperatures but not to higher storage moduli. This was interpreted as a lack of cross-link formation in the three-dimensional network structure of the gels. A single sol–gel transition diagram for monovalent cations is proposed, in which different zones associated with the presence of ordered and disordered conformations serve to identify the conditions in which HAG can exist in aqueous media.     

Effect of addition of sucrose and aspartame on the compression resistance of hydrocolloids gels

The effect of adding sucrose (5–25% w/w) and aspartame (0.04–0.16% w/w) on the compression resistance of three hydrocolloid gelled systems: κ‐carrageenan, gellan gum and κ‐carrageenan/locust bean gum at three different concentrations (0.3, 0.75 and 1.2% w/w) was studied. Sucrose addition increased true rupture stress in the three‐gelled systems, this effect being stronger in gellan gels. The deformability modulus increased with sucrose concentration in gellan gels, but not in the other systems. Rupture stress and deformability modulus increased with the addition of sucrose only in the harder gels (0.75 and 1.2% w/w). The effect of sucrose addition on the true rupture strain was significant but, in general, not important, mainly for lower gum concentrations. Aspartame addition did not affect the compression parameters.     

Compressive textural attributes, opacity and syneresis of gels prepared from gellan, agar and their mixtures

Gellan, agar and their mixed gels at an equal proportion of both were subjected to uniaxial compression to determine the textural attributes including fracture characteristics, opacity and syneresis. An increase in concentration of hydrocolloids increased opacity but decreased syneresis. Highly transparent gellan gels with opacity less than 8% were obtained; opacity of agar gels was highest, and was between 5% and 30% for their mixed gels. Syneresis as low as 1.5% was observed with the mixed gel containing 2% each of agar and gellan. The maximum stress and energy for compression increased with the level of gelling agents while instantaneous relaxation in height decreased. Binary combinations or mixed gels containing agar and gellan can provide unique textural and physical characteristics like syneresis and opacity.     

Gelation and microstructure of dilute gellan solutions with calcium ions

The viscoelasticity at 25 °C and microstructure of 0.02–0.07 wt% of low acyl gellan aqueous media were investigated for ratios of Ca²⁺ to gellan in the range of 0–38.8, using small amplitude oscillatory shear rheometry and confocal laser scanning microscopy (CLSM), respectively. The total ionic concentration (C_T = γ C_P + C_S, being C_P and C_S the gellan and calcium concentrations, respectively, and γ the mean activity coefficient) of the systems was found to be the triggering and critical factor for the gelation and elasticity of gellan systems. The gel point (T_gel) and storage moduli (G′) increased upon increasing C_T. However, G′ showed a maximum for C_T = 9.3 ± 1.2 meq/L, followed by a progressive reduction as C_T increased; this was primarily due to further addition of calcium, as C_P had a low contribution to C_T of the systems. CLSM demonstrated that the level of counter-ions was enough to induce the formation of a network, whose connection depended on C_P and whose reinforcement was ion dependent. Therefore, even at very low levels of gellan, it is possible to create a wide spectrum of viscoelastic behaviors going from structured liquids to strong gels through the specific combinations of gellan and cation concentrations.     

Viscoelastic characterization of fluid and gel like food emulsions stabilized with hydrocolloids

Food emulsions exhibit a great diversity of rheological characteristics; hydrocolloids are usually added to deal with creaming instability. Viscoelastic measurements provide information about the microstructure of the system. The objectives of this work were: a) to determine the viscoelastic behavior of two different low in fat oil-in-water food emulsions: a gel like and a fluid type emulsions stabilized with hydrocolloids (gellan gum and xanthan-guar mixtures respectively) b) to model and predict the mechanical relaxation spectrum for both emulsions and continuous aqueous phases. Low-in-fat oil-in-water emulsions (20 g/100 g) were prepared using sunflower oil and Tween 80 (1 wt.%). Fluid emulsions containing xanthan and guar gums were formulated using a synergistic ratio 7:3, with total hydrocolloid concentration ranging between 0.5 to 2 wt%. The aqueous phases contained NaCl (2 wt.%) and acetic acid (2 wt.%). The effect of hydrocolloids was studied using oscillatory measurements (G’ and G” vs. frequency) within the linear viscoelastic range previously determined by stress-sweeps. Time-Concentration Superposition principle was applied to find the master curves that describe the mechanical spectra of the viscoelastic materials. Superposition allows to obtain a wide spectrum of nearly ten decades of frequencies in emulsions containing xanthan–guar mixtures, whereas gellan gum systems did not show a significant frequency displacement. Viscoelastic behavior of the systems was satisfactorily modeled using Baumgaertel-Schausberger-Winter (BSW) equation. This empirical model was used to predict the mechanical relaxation spectrum for both emulsions and continuous aqueous phases. Validation of the predicted spectra was carried out through creep compliance data for emulsion-filled gels and steady-state flow curves for emulsions containing xanthan–guar mixtures.