Non-newtonian thermal analysis of an EHD contact lubricated with MIL-L-23699 oil

A thermal and non-Newtonian fluid model under elastohydrodynamic lubrication conditions is proposed, integrating some particularities, such as the separation between hydrodynamic and dissipative phenomena inside the contact. The concept of apparent viscosity is used to introduce the non-Newtonian behaviour of the lubricant and the thermal behaviour of the contact into the Reynolds equation, acting as a link element between the hydrodynamic and dissipative components of the EHD film, independently of the rheological and thermal models considered. The apparent viscosity enables the application of the rheological model better adapted to each lubricant, without appealing to special formulations of the EHD problem.The Newton–Raphson technique is used to obtain the lubricant film geometry and the pressure distribution inside the EHD contact. The shear stresses developed in the fluid film are evaluated assuming the non-linear Maxwell rheological model. The surfaces and lubricant temperature distributions are determined using the simplified Houpert's method, applied to the inlet contact zone, and the thermal method proposed by Tevaarwerk is applied in the high pressure contact zone.The non-Newtonian thermal EHD model is applied to the analysis of a contact lubricated with MIL-L-23699 oil. Significant results are obtained for the centre and minimum film thickness, for the inlet shear heating and film thickness reduction factor (φ_T), for the temperature rise of the lubricant and of the surfaces and for the friction coefficient inside the contact, considering wide ranges of the operating conditions (maximum Hertzian pressure, inlet oil temperature, rolling speed and slide-to-roll ratio).Finally, the numerical traction curves determined are compared with the corresponding experimental results, showing very good correlation.     

基于Carreau流变模型的圆柱滚子轴承热混合润滑分析*

为了研究圆柱滚子轴承接触区的混合润滑性能,建立基于Carreau非牛顿流体的热混合润滑模型,求解非牛顿流体线接触热混合润滑数值解。研究滑滚比、卷吸速度及载荷对线接触混合润滑特性的影响,并与相同工况下牛顿流体热混合润滑的结果进行对比。结果表明：随着滑滚比、卷吸速度及载荷的增大,油膜温度都会升高,Carreau非牛顿流体的温度要低于牛顿流体的温度;油膜厚度随着滑滚比、载荷的增大而减小,随着卷吸速度的增大而增大,Carreau非牛顿流体与牛顿流体膜厚相差不大;随着滑滚比的增大,2种流体的平均摩擦因数均增大,随着卷吸速度和载荷的增大,2种流体的载荷比均减小。     

Numerical modeling an elastohydrodynamic contact of shaped rollers with allowance for misalignment of their axes

A method of numerically solving an elastohydrodynamic (EHD) contact of shaped rollers with allowance for misalignment of their axes in a plane perpendicular to the rolling direction is advanced. The mode of EHD lubrication is typical of such friction assemblies as roller bearings and gearings, in which the contacting elastic bodies are separated by a lubricant film and deformed under the action of an external load. Results of numerical modeling demonstrate the significant effect of the misalignment angle on the distribution of pressure and thickness of the lubricant film in the EHD contact and can be used further to analyze friction in a contact area and the stress tensor in a subsurface layer. The mathematical model of the EHD contact is described through nonlinear integro-differential equations and inequalities. The computational algorithm is based on Newton’s method.     

The investigation of oil film thickness in heavily-loaded contact

An experimental study of the shape and thickness of the oil film during rolling in a thrust ball bearing has been carried out by the interference method.The experimental results showed good agreement with theory. Oil film thickness was affected mainly by the rolling velocity, viscosity of oil and maximum Hertzian stress. The groove radius had no effect on the film thickness. With increase of rolling velocity the film thickness increases and then reduces sharply owing to temperature rise and the non-Newtonian properties of the lubricant. A qualitative similarity was derived from the experimentally observed dimensionless shapes of the film and of the dimensionless theoretical shapes of the oil film for the lubricant in the non-Newtonian state. The flat “squashed” contact area diminished and disappeared with rise in velocity, which agreed with theoretical predictions.Good agreement was found between the theoretical and the experimental values of the oil film thickness and the friction coefficients for a ball sliding on a plane. Values of relaxation time for oil agree with values observed by the vibration method.The interference method is proposed to estimate the relation of the relaxation time for lubricants to the pressure and temperature up to maximum Hertzian pressures of 14,000 kg/cm². Experimental studies by the interference method and the solution of the non-isothermal hydrodynamic contact problem for liquids both in the Newtonian and non-Newtonian state provide a method of calculation of the friction coefficient.     

Measurement of the Rheology of Lubricant Films Within Elastohydrodynamic Contacts

There is growing need for a reliable model of the rheological response of lubricants in elastohydrodynamic (EHD) contacts, not only to predict behaviour in full-film EHD conditions, but also for use in modelling mixed-film lubrication. One barrier to developing such a model is that measurements of friction actually represent averaged values over the whole, lubricated contact under study. However the fluid film conditions of temperature, pressure and strain rate generally vary over such contacts, which makes it difficult to determine constitutive shear-stress equations from friction measurements. This paper examines the various different techniques used to study the origins of EHD friction and the underlying film rheology. It then describes and applies a technique for obtaining the temperature rise maps of both solid surfaces in a rolling-sliding EHD contacts and thus shear-stress and friction maps. The work shows that the shear stress of the traction fluid studied increases approximately linearly with pressure and decreases approximately linearly with temperature in the high-pressure central region of EHD contacts.     

Effect of Base Oil Structure on Elastohydrodynamic Friction

The EHD friction properties of a wide range of base fluids have been measured and compared in mixed sliding–rolling conditions at three temperatures and two pressures. The use of tungsten carbide ball and disc specimens enabled high mean contact pressures of 1.5 and 2.0 GPa to be obtained, comparable to those present in many rolling bearings. The measurements confirm the importance of molecular structure of the base fluid in determining EHD friction. Liquids having linear-shaped molecules with flexible bonds give considerably lower friction than liquids based on molecules with bulky side groups or rings. EHD friction also increases with viscosity for liquids having similar molecular structures. Using pure ester fluids, it is shown that quite small differences in molecular structure can have considerable effects on EHD friction. The importance of temperature rise in reducing EHD friction at slide–roll ratios above about 5% has been shown. By measuring EHD friction at several temperatures and pressures as well as EHD film thickness, approximate corrections to measured EHD friction data have been made to obtain isothermal shear stress and thus EHD friction curves. These show that under the conditions tested most low molecular weight base fluids do not reach a limiting friction coefficient and thus shear stress. However, two high traction base fluids appear to reach limiting values, while three linear polymeric base fluids may also do so. Constants of best fit to a linear/logarithmic isothermal shear stress/strain rate relationship have been provided to enable reconstruction of isothermal EHD friction behaviour for most of the fluids tested.     

Thermal Elastohydrodynamic Lubrication of Point Contacts Using a Newtonian/Generalized Newtonian Lubricant

The classical ElastoHydroDynamic (EHD) theory assumes a Newtonian lubricant and an isothermal operating regime. In reality, lubricating oils do not behave as perfect Newtonian fluids. Moreover, in most operating conditions of an engineering system, especially at high speeds, thermal effects are important and temperature can no longer be considered as constant throughout the system. This is one reason why there has always been a gap between numerical results and experimental data. This paper aims to show that this gap can be reduced by taking into consideration the heat generation that takes place in the contact and using appropriate rheological models. For this, a unique thermal ElastoHydrodynamic lubrication model is developed for both Newtonian and non-Newtonian lubricants. Pressure, film thickness and traction results are then compared to their equivalent isothermal results and experimental data. The agreement between thermal calculations and experiments reveals the necessity of considering thermal effects in EHD models.     

Influence of Mixed-Lubrication and Rough Elastic-Plastic Contact on the Performance of Small Fluid Film Bearings

A previously developed deterministic elastohydrodynamic (EHD) numerical model for small fluid film bearings functioning in the mixed lubrication regime is extended in this work by considering the rough contact. Several simplifying hypotheses are made: the shaft is considered rigid and smooth, turning at low speeds (isothermal regime), and the pad is assumed to have an elastic-perfectly-plastic behavior. The Reynolds equation is solved on a very fine mesh and the elasto-plastic pad deformation caused by the hydrodynamic pressure is taken into account. A deterministic active set-based method is used for determining the contact pressure, the contact extent, and the corresponding deformation. The results are presented for a partial journal bearing configuration, with a linear shaft velocity of 0.47 m/s under specific pressures varying up to 50 MPa. Two pad materials are considered, and the lubricant is either isoviscous or piezoviscous oil. The simulation results, presented as a function of the bearing specific pressure, include eccentricity, the film thickness, the friction torques, the contact extent, etc. Stribeck curves showing the evolution of the friction coefficient in the hydrodynamic and mixed lubrication regimes are also discussed.     

Thermal effects in elastohydrodynamic lubrication of line contacts using a non-Newtonian lubricant

A Reynolds' equation, using Winer's viscoplastic model to express the non-Newtonian fluid property, is derived for line-contact EHL problems. The numerical solutions are obtained to the incorporated Reynolds', elasticity, and energy equations for pressure, film thickness, and temperature distribution between two surfaces simultaneously having rolling and sliding motions. The results are presented for thermal non-Newtonian lubrication, to observe the difference between Winer's equation and Trachman's expression on temperature distribution, pressure, and film thickness. The variation in friction coefficient with slip shear rate is in agreement with other experimental data.     

Quantitative Viscosity Mapping Using Fluorescence Lifetime Measurements

Lubricant viscosity is a key driver in both the tribological performance and energy efficiency of a lubricated contact. Elastohydrodynamic (EHD) lubrication produces very high pressures and shear rates, conditions hard to replicate using conventional rheometry. In situ rheological measurements within a typical contact are therefore important to investigate how a fluid behaves under such conditions. Molecular rotors provide such an opportunity to extract the local viscosity of a fluid under EHD lubrication. The validity of such an application is shown by comparing local viscosity measurements obtained using molecular rotors and fluorescence lifetime measurements, in a model EHD lubricant, with reference measurements using conventional rheometry techniques. The appropriateness of standard methods used in tribology for high-pressure rheometry (combining friction and film thickness measurements) has been verified when the flow of EHD lubricant is homogeneous and linear. A simple procedure for calibrating the fluorescence lifetime of molecular rotors at elevated pressure for viscosity measurements is proposed.