共查询到20条相似文献,搜索用时 93 毫秒
1.
3-(R)RC并联机器人动力学分析 总被引:1,自引:0,他引:1
对一种空间3自由度并联机器人(3-RRC并联机器人1进行动力学分析.此并联机器人的机构由一个动平台和一个静平台通过3个同样的转动副一转动副一圆柱副支链组成.基于Lagrange方程导出3-RRC并联机器人的动力学模型,并分析此并联机器人的动力学特性.通过一个算例,讨论3-RRC并联机器人的等效转动惯量、驱动力/力矩和能耗的变化规律.结果表明,对于给定的运动规律,机构位形对系统的等效转动惯量和驱动力/力矩的影响很大.研究对进一步分析3-RRC并联机器人的动态特性、机构优化设计和系统控制等实际工程应用具有重要意义. 相似文献
2.
对一种空间3自由度并联机器人(3-■RC并联机器人)进行动力学分析。此并联机器人的机构由一个动平台和一个静平台通过3个同样的转动副—转动副—圆柱副支链组成。基于Lagrange方程导出3-■RC并联机器人的动力学模型,并分析此并联机器人的动力学特性。通过一个算例,讨论3-■RC并联机器人的等效转动惯量、驱动力/力矩和能耗的变化规律。结果表明,对于给定的运动规律,机构位形对系统的等效转动惯量和驱动力/力矩的影响很大。研究对进一步分析3-■RC并联机器人的动态特性、机构优化设计和系统控制等实际工程应用具有重要意义。 相似文献
3.
[PP]S类并联机器人机构姿态描述方法 总被引:7,自引:2,他引:5
具有至少两个转动自由度的空间并联机器人机构的姿态描述是机构运动学分析的一个重要内容,描述方法对机构性能分析起着重要作用.[PP]S类并联机器人机构(连接动平台的三个球铰链始终在固定的平面内作平面运动的并联机器人机构)的动平台具有一个移动和两个转动自由度,是并联机器人机构的重要分支之一,位姿描述也是国内外研究的重点.介绍一种用两个角度描述 [PP]S类并联机器人机构姿态的方法,采用该姿态描述方法,[PP]S类并联机器人机构的位姿描述参数可以减少到5个,而且没有绕垂直于动平台平面的轴线的转动伴随运动,减小了此类并联机器人机构运动学分析的难度.与采用3个欧拉角的姿态描述方法相比,这种方法具有运动学描述简单以及伴随运动和姿态工作空间描述方便等优点,符合工程应用需要,是值得推广的一种姿态描述方法. 相似文献
4.
5.
6.
针对二转动一平动(2R1T)三自由度并联机器人,基于螺旋理论,提出了可能的支链方案.分析了支链只存在单约束线矢力的情形,利用互易螺旋,得到支链运动副组合及其相应的设计原则.由于空间线矢力对转动与平动自由度都有影响,讨论了此类并联机器人自由度与约束线矢力空间分布之间的关系.综合支链运动副设计原则与机构设计所需线矢力空间分布,可得到符合实际应用的具有2R1T运动特征的并联机器人.通过对3-RPS三自由度并联机构的分析,具体说明了空间线矢力与并联机构自由度之间的相互影响.同时,此种机构综合方法也适用于其它少自由度并联机构构型的综合与优化设计. 相似文献
7.
一种新型3自由度并联机构的奇异性分析 总被引:4,自引:0,他引:4
研究一种新型空间3自由度并联机构(HANA)的奇异性。该机构由定平台、动平台和三个联接支链组成,其动平台相对于定平台具有2个移动和1个转动自由度。其结构主要特点是只采用了单自由度的运动副。构型优势主要是转动自由度灵活度高。详细分析了该机构的三类奇异形位,为以后关于该机构的工作空间和转动能力分析以及控制提供基础,特别是基于合理设计的工作空间内无奇异特性将保证该机构拥有很高的转动能力。该机构不仅可以应用在并联机床的设计中,还可以广泛地应用在工业机器人、飞行模拟器和微型机器人等领域。 相似文献
8.
9.
一种三维平移正交并联机构及其位置分析 总被引:2,自引:0,他引:2
根据并联机器人机构结构综合理论,提出了一种新型的能实现三雏纯平移的空间3-P⊥R⊥4r⊥R三自由度正交并联机器人机构.该机构通过动平台和定平台的3个全部由转动副和移动副构成的约束支链连接,使定平台上3个直线移动驱动副的轴线两两互相垂直.根据杆长约束条件,推导了完全封闭形式的位王正、反解.分析结果为该机构的设计及实用化提供了理论依据. 相似文献
10.
11.
特殊3-PRS并联机器人运动分析 总被引:2,自引:0,他引:2
建立了 P副平行于固定平台法线的 3- PRS并联机器人的运动反解数学模型。分析了当给定运动平台中心法线与固定平台中心法线之间夹角 ,并使运动平台法线绕固定平台中心法线旋转时 ,运动平台中心以及中心法线上一点的运动轨迹。分析表明 ,该 3- PRS并联机器人只能部分满足特定的运动规律要求 相似文献
12.
13.
Kinematic analysis of a hybrid serial-parallel manipulator 总被引:1,自引:1,他引:0
X. Z. Zheng H. Z. Bin Y. G. Luo 《The International Journal of Advanced Manufacturing Technology》2004,23(11-12):925-930
The kinematic analysis of a new type hybrid serial-parallel manipulator is presented. This manipulator is based on two kinds of 3-UPU parallel mechanisms (PM). Each 3-UPU possesses one platform, one base and three limbs, and hence has 3 degrees of freedom (DOF). Each limb comprises of universal (U), prismatic (P), and universal (U) joints in series. Therefore the hybrid manipulator has totally 6 degrees of freedom and has also an elegant structure. The moving platform (mid platform) of the first PM moves with pure translation with respect to the fixed base and the moving platform (end platform) in the second PM only changes its orientation with respect to the mid platform. In this paper, closed-form kinematic solutions are obtained for this type of mechanism and related theoretical results have been verified numerically. 相似文献
14.
提出了一种能够实现三维移动的空间新型三自由度并联机构,其固定平台与运动平台通过对称布置的CU支链相连接.基于该机构运动约束方程,得到位置反解、正解和速度方程的封闭表达式.最后,应用实例验证了理论分析的正确性. 相似文献
15.
16.
《机械工程学报(英文版)》2020,33(4):63-76
The hydraulic parallel manipulator combines the high-power density of the hydraulic system and high rigidity of the parallel mechanism with excellent load-carrying capacity. However, the high-precision trajectory tracking control of the hydraulic parallel manipulator is challenged by the coupling dynamics of the parallel mechanism and the high nonlinearities of the hydraulic system. In this study, the trajectory control of a 3-DOF symmetric spherical parallel 3 UPS/S manipulator is evaluated. Focusing on the highly coupling and nonlinear system dynamics, a compound impedance control method for a hydraulic driven parallel manipulator is proposed, which combines impedance control with the spatial motion characteristics of a parallel manipulator. The control strategy is divided into the inner and outer loops. The inner loop controls the impedance of the actuator in the joint space, and the outer loop controls the impedance of the entire platform in the task space to compensate the coupling of the actuators and improve the tracking accuracy of the moving platform. Compound impedance control does not require force or pressure sensors and is less dependent on modeling precision. The experimental results show that the compound impedance control e ectively improves the tracking accuracy of the moving platform. This research proposes a compound impedance control strategy for a 3-DOF hydraulic parallel manipulator, which has high tracking precision with a simple and cheap system configuration. 相似文献
17.
Singular configurations must be avoided in path planning and control of a parallel manipulator. However, most studies rarely focus on an overall singularity loci distribution of lower-mobility parallel mechanisms. Geometric algebra is employed in analysis of singularity of a 3-RPS parallel manipulator. Twist and wrench in screw theory are represented in geometric algebra. Linear dependency of twists and wrenches are described by outer product in geometric algebra. Reciprocity between twists and constraint wrenches are reflected by duality. To compute the positions of the three spherical joints of the 3-RPS parallel manipulator, Tilt-and-Torsion angles are used to describe the orientation of the moving platform. The outer product of twists and constraint wrenches is used as an index for closeness to singularity(ICS) of the 3-RPS parallel manipulator. An overall and thorough perspective of the singularity loci distribution of the 3-RPS parallel manipulator is disclosed, which is helpful to design, trajectory planning and control of this kind of parallel manipulator. 相似文献
18.
针对一种特殊3-UCR并联机构,基于反螺旋理论与虚拟机构法对其瞬态运动特性进行了分析,利用支链与动平台的一阶影响系数矩阵之间的关系,建立了此并联机构在螺旋坐标系下的瞬态运动数学模型,得出了一阶影响系数矩阵只与机构输入参数、机构构型有关的结论,同样此建模方法适用于其它欠自由度并联机构的瞬态运动特性分析。通过此数学模型,研究得到任意瞬态的螺旋系节距,表明该机构具有两转动一平动的瞬态运动特性,并利用动静平台平行位姿时的具体数值实例,验证了此瞬态运动特性符合前述分析结果。 相似文献
19.
Li ShihuaHuang ZhenCollege of Mechanical Engineering Yanshan University Qinhuangdao China 《机械工程学报(英文版)》2005,18(3):376-381
0 INTRODUCTIONA new hotspot of the research of parallel robots is the newstyle lower-mobility (2~5) parallel robots at present. Because osimple structure and low cost, the lower-mobility parallel robotcould be widely applied in industry and other field. O… 相似文献
20.
绳牵引并联机构奇异性分析及无奇异机构设计 总被引:1,自引:1,他引:0
绳牵引并联机构是将驱动器的运动和力以绳为介质并行转换成动平台的运动和力的装置,其末端执行器的自由度数可定义为机构的结构矩阵的所有旋量正张成的实数空间的维数。指出绳牵引并联机构仅有过运动性的奇异类型,阐明该奇异是一种由于位姿几何的特殊导致动平台的力旋量集合的维数降秩的现象;以一个1R2T机构为例指出了机构的奇异性除了会导致机构失去控制,还会导致绳优化拉力分布的不连续性:以1-2-1型的1R2T 机构为例研究动平台的重力会对机构的奇异性所造成的影响,从而发现即便动平台重力无法消除机构的奇异点, 但却能使各根绳的拉力分布重新得以配置。提出用各个转动自由度相互解耦,而平动运动能得到完全控制的机构是无奇异的这个原理来构造无奇异性的1-2-1型的CRPM(1R2T)、2-3-2型的RRPM-7(2R3T)的方法;提出用对心抓取定理构造无奇异性的2-2型的CRPMs(1R2T)和3-3型的CRPM(2R3T)的方法;提出用3维力封闭抓取定理构造无奇异性的3-3-3型的RRPM-9(3R3T)的方法。 相似文献