The observation of intact hepatic endothelial cells by cryo-electron microscopy

Liver sinusoidal endothelial cells (LSECs) can optimally be imaged by whole mount transmission electron microscopy (TEM). However, TEM allows only investigation of vacuum‐resistant specimens and this usually implies the study of chemically fixed and dried specimens. Cryo‐electron microscopy (cryo‐EM) can be used as a good alternative for imaging samples as whole mounts. Cryo‐EM offers the opportunity to study intact, living cells while avoiding fixation, dehydration and drying, at the same time preserving all solubles and water as vitrified ice. Therefore, we compared the different results obtained when LSECs were vitrified using different vitrification conditions. We collected evidence that manual blotting at ambient conditions and vitrification by the guided drop method results in the production of artefacts in LSECs, such as the loss of fenestrae, formation of gaps and lack of structural details in the cytoplasm. We attribute these artefacts to temperature and osmotic effects during sample preparation just prior to vitrification. By contrast, by using an environmentally controlled glove box and a vitrification robot (37 °C and 100% relative humidity), these specific structural artefacts were nearly absent, illustrating the importance of controlled sample preparation. Moreover, data on glutaraldehyde‐fixed cells and obtained by using different vitrification methods suggested that chemical prefixation is not essential when vitrification is performed under controlled conditions. Conditioned vitrification therefore equals chemical fixation in preserving and imaging cellular fine structure. Unfixed, vitrified LSECs show fenestrae and fenestrae‐associated cytoskeleton rings, indicating that these structures are not artefacts resulting from chemical fixation.     

Amorphous solid water produced by cryosectioning of crystalline ice at 113 K

Amorphous solid (vitreous) water can be obtained by a number of methods, including quick freezing of a very small volume of pure water, low pressure condensation of water vapour on a cold substrate or transformation of hexagonal ice (the ice which is naturally formed) under very high pressure at liquid nitrogen temperature. Larger volumes can be vitrified if cryoprotectant is added or when samples are frozen under high pressure. We show that a sample of 17.5% dextran solution or mouse brain tissue, respectively, frozen under high pressure (200 MPa) into cubic or hexagonal ice can be transformed into vitreous water by the very process of cryosectioning. The vitreous sections obtained by this procedure differ from cryosections obtained from vitreous samples by the irregular aspect of the sections and by small but significant differences in the electron diffraction patterns. For the growing community of cryo‐ultramicrotomists it is important to know that vitrification can occur at the knife edge. A vitreous sample is considered to show the best possible structural preservation. The sort of vitrification described here, however, can lead to bad structural preservation and is therefore considered to be a pitfall. Furthermore, we compare these sections with other forms of amorphous solid water and find it similar to high density amorphous water produced at very high pressures (about 1 GPa) from hexagonal ice and annealed close to its transformation temperature at 117 K.     

Vitrification of aqueous suspensions from a controlled environment for electron microscopy: An improved plunge-cooling device

In the process of vitrifying aqueous suspensions for cryotransmission electron microscopy, water is solidified without crystallization. Vitrification can be achieved by rapidly plunging an aqueous thin film into a liquid cryogen. The preparation of aqueous thin films prior to vitrification must be performed in an environmental cabinet at controlled temperature and humidity in order to prevent evaporation and temperature-induced phase changes in the thin film. The device described here incorporates several important features which make the apparatus simpler and more convenient to use than similar devices described in the literature. One of these features includes the use of a totally enclosed environmental cabinet in which the grid, sample, micropipette and absorbent paper are equilibrated before thin-film preparation. Other features include a cryogen dewar on a swing arm for easy refilling, a guillotine shutter which is used to trigger the plunger electrically and a semiautomatic system which facilitates rapid transfer of the vitrified specimen from liquid propane to liquid nitrogen for storage and reduces handling of the specimen. To demonstrate the utility of the device, results showing the influence of temperature on the morphology of phospholipid vesicles are presented. A commercial cryotransfer apparatus (which is used for transportation of the vitrified specimen to the electron microscope cold-stage) has been modified to reduce the possibility of reversion of the vitreous phase to the crystalline ice phases.     

New controlled environment vitrification system for preparing wet samples for cryo-SEM

A new controlled environment vitrification system (CEVS) has been designed and constructed to facilitate examination by cryogenic scanning electron microscopy (Cryo‐SEM) of initial suspension state and of microstructure development in latex, latex–composite and other coatings while they still contain solvent. The new system has a main chamber with provisions for coating as well as drying, and for well‐controlled plunging into cryogen. An added subsidiary chamber holds samples for drying or annealing over minutes to days before they are returned to the main chamber and plunged from it. In the main chamber, samples are blade‐coated on 5 × 7 mm pieces of silicon wafer and held at selected temperature and humidity for successively longer times, either there or after transfer along a rail into the subsidiary chamber. They are then placed in the sample holder mounted on the plunge rod, so as to permit adjustment of the sample's attitude when it plunges, at controlled speed, into liquid ethane at its freezing point, to a chosen depth, in order to solidify the sample without significant shear or freezing artifacts. The entries of plunging samples and related sample holders into liquid ethane were recorded with a high‐speed, high‐resolution Photron digital camera. The data were interpreted with a new hypothesis about the width of the band of extremely rapid cooling by deeply subcooled nucleate boiling below the line of entry. Complementary cryo‐SEM images revealed that the freezing rate and surface shearing of a sample need to be balanced by adjusting the plunging attitude.     

Controlled environment vitrification system: An improved sample preparation technique

The controlled environment vitrification system (CEVS) permits cryofixation of hydrated biological and colloidal dispersions and aggregates from a temperature- and saturation-controlled environment. Otherwise, specimens prepared in an uncontrolled laboratory atmosphere are subject to evaporation and heat transfer, which may introduce artifacts caused by concentration, pH, ionic strength, and temperature changes. Moreover, it is difficult to fix and examine the microstructure of systems at temperatures other than ambient (e.g., biological systems at in vivo conditions and colloidal systems above room temperature). A system has been developed that ensures that a liquid or partially liquid specimen is maintained in its original state while it is being prepared before vitrification and, once prepared, is vitrified with little alteration of its microstructure. A controlled environment is provided within a chamber where temperature and chemical activity of volatile components can be controlled while the specimen is being prepared. The specimen grid is mounted on a plunger, and a synchronous shutter is opened almost simultaneously with the release of the plunger, so that the specimen is propelled abruptly through the shutter opening into a cryogenic bath. We describe the system and its use and illustrate the value of the technique with TEM micrographs of surfactant microstructures in which specimen preparation artifacts were avoided. We also discuss applications to other instruments like SEM, to other techniques like freeze-fracture, and to novel “on the grid” experiments that make it possible to freeze successive instants of dynamic processes such as membrane fusion, chemical reactions, and phase transitions.     

Vitreous cryo-sectioning of cells facilitated by a micromanipulator

Sectioning vitrified cells and tissues for cryo‐electron microscopy is more challenging than room‐temperature sectioning of plastic‐embedded samples. As the sample must be kept very cold (相似文献   

Focused ion beam milling of vitreous water: prospects for an alternative to cryo-ultramicrotomy of frozen-hydrated biological samples

The feasibility of using a focused ion beam (FIB) for the purpose of thinning vitreously frozen biological specimens for transmission electron microscopy (TEM) was explored. A concern was whether heat transfer beyond the direct ion interaction layer might devitrify the ice. To test this possibility, we milled vitreously frozen water on a standard TEM grid with a 30‐keV Ga⁺ beam, and cryo‐transferred the grid to a TEM for examination. Following FIB milling of the vitreous ice from a thickness of approximately 1200 nm to 200–150 nm, changes characteristic of heat‐induced devitrification were not observed by TEM, in either images or diffraction patterns. Although numerous technical challenges remain, it is anticipated that ‘cryo‐FIB thinning’ of bulk frozen‐hydratred material will be capable of producing specimens for TEM cryo‐tomography with much greater efficiency than cryo‐ultramicrotomy, and without the specimen distortions and handling difficulties of the latter.     

A technique for improved focused ion beam milling of cryo-prepared life science specimens

The combination of focused ion beam and scanning electron microscopy with a cryo‐preparation/transfer system allows specimens to be milled at low temperatures. However, for biological specimens in particular, the quality of results is strongly dependent on correct preparation of the specimen surface. We demonstrate a method for deposition of a protective, planarizing surface layer onto a cryo‐sample, enabling high‐quality cross‐sectioning using the ion beam and investigation of structures at the nanoscale.     

Cryogenic‐temperature electron microscopy direct imaging of carbon nanotubes and graphene solutions in superacids

Cryogenic electron microscopy (cryo‐EM) is a powerful tool for imaging liquid and semiliquid systems. While cryogenic transmission electron microscopy (cryo‐TEM) is a standard technique in many fields, cryogenic scanning electron microscopy (cryo‐SEM) is still not that widely used and is far less developed. The vast majority of systems under investigation by cryo‐EM involve either water or organic components. In this paper, we introduce the use of novel cryo‐TEM and cryo‐SEM specimen preparation and imaging methodologies, suitable for highly acidic and very reactive systems. Both preserve the native nanostructure in the system, while not harming the expensive equipment or the user. We present examples of direct imaging of single‐walled, multiwalled carbon nanotubes and graphene, dissolved in chlorosulfonic acid and oleum. Moreover, we demonstrate the ability of these new cryo‐TEM and cryo‐SEM methodologies to follow phase transitions in carbon nanotube (CNT)/superacid systems, starting from dilute solutions up to the concentrated nematic liquid‐crystalline CNT phases, used as the ‘dope’ for all‐carbon‐fibre spinning. Originally developed for direct imaging of CNTs and graphene dissolution and self‐assembly in superacids, these methodologies can be implemented for a variety of highly acidic systems, paving a way for a new field of nonaqueous cryogenic electron microscopy.     

Vitrification of articular cartilage by high-pressure freezing

For more than 20 years, high-pressure freezing has been used to cryofix bulk biological specimens and reports are available in which the potential and limits of this method have been evaluated mostly based on morphological criteria. By evaluating the presence or absence of segregation patterns, it was postulated that biological samples of up to 600 μm in thickness could be vitrified by high-pressure freezing. The cooling rates necessary to achieve this result under high-pressure conditions were estimated to be of the order of several hundred degrees kelvin per second. Recent results suggest that the thickness of biological samples which can be vitrified may be much less than previously believed. It was the aim of this study to explore the potential and limits of high-pressure freezing using theoretical and experimental methods. A new high-pressure freezing apparatus (Lei?a EM HPF), which can generate higher cooling rates at the sample surface than previously possible, was used. Using bovine articular cartilage as a model tissue system, we were able to vitrify 150-μm-thick tissue samples. Vitrification was proven by subjecting frozen-hydrated cryosections to electron diffraction analysis and was found to be dependent on the proteoglycan concentration and water content of the cartilage. Only the lower radical zone (with a high proteoglycan concentration and a low water content compared to the other zones) could be fully vitrified. Our theoretical calculations indicated that applied surface cooling rates in excess of 5000 K/s can be propagated into specimen centres only if samples are relatively thin (<200 μm). These calculations, taken together with our zone-dependent attainment of vitrification in 150-μm-thick cartilage samples, suggest that the critical cooling rates necessary to achieve vitrification of biological samples under high-pressure freezing conditions are significantly higher (1000–100 000 K/s) than previously proposed, but are reduced by about a factor of 100 when compared to cooling rates necessary to vitrify biological samples at ambient pressure.