排序方式: 共有7条查询结果,搜索用时 31 毫秒
1
1.
2.
采用搅拌摩擦焊接工艺焊接8mm厚2219铝合金板材,自行研制设计了高频感应加热装置,对2219铝合金搅拌摩擦焊接接头进行了应力表征与高频感应加热去应力研究,试验温度分别为90℃、140℃、190℃,利用X射线衍射法测试了焊缝热处理前、后纵向和横向残余应力,分析了搅拌摩擦焊接头微观组织和力学性能。结果表明,经高频感应加热处理后,焊接纵向残余应力峰值显著降低,经190℃感应加热处理后纵向残余应力峰值下降51.3%,残余拉应力区间变窄,随着高频感应加热温度的降低,去应力效果减弱。热处理前、后焊接接头微观组织和力学性能变化不明显,显微硬度分布趋势相同,说明高频感应加热技术在有效降低焊接残余应力的同时不改变焊接接头的力学性能。 相似文献
3.
Preparation of TiO2 nanotube on glass by anodization of Ti films at room temperature 总被引:1,自引:0,他引:1
In order to fabricate titania nanotubes on glass substrate, Ti thin films (700-900 nm) were first deposited by radio-frequency(RF) magnetron sputtering and then anodized in an aqueous HF electrolyte solution at room temperature. The morphology and structure of the nanotubes were identified by means of field emission scanning electron microscopy(FE-SEM) and X-ray diffractometry(XRD). The effects of anodization parameters (concentration of electrolyte, applied voltage) on nanotube morphology were comprehensively investigated. The results show that the dense and crystalline Ti film can be obtained on the unheated glass substrate under the sputtering power of 150 W, and the anodization current and voltage play significant roles in the formation of titania nanotube with different tube sizes. 相似文献
4.
5.
利用铜模铸造法制备(La0.6Ce0.4)65Al10Cu25块体非晶合金,通过X射线衍射和差示扫描量热法对该非晶合金的热稳定性和晶化行为进行研究。利用J-M-A方程对其等温晶化动力学进行分析,该合金平均Avrami指数在2.39~3.38之间。区域Avrami指数n(x)分析表明,晶化初期n(x)趋于3;晶化中期阶段,n(x)由2.5变化到3.5,在此过程中,当2.5相似文献
6.
7.
利用铜模铸造法制备了(La0.6Ce0.4)65Al10Cu25块体非晶合金,并在其过冷液相区内不同温度下,采用不同压力对该非晶合金进行加压退火处理,通过X射线衍射仪和差示扫描量热法研究了加压退火处理对该非晶合金晶化行为及热稳定性的影响。结果表明,加压退火促进了(La0.6Ce0.4)65Al10Cu25非晶合金的晶化过程,使得晶化初始温度Tx降低(dTx/dP=-5.17K/GPa),晶化激活能Ep随退火压力的增加而增大,并从能量和化学短程序畴的角度解释了加压退火对(La0.6Ce0.4)65Al10Cu25非晶合金晶化过程的影响机理。 相似文献
1