排序方式: 共有23条查询结果,搜索用时 46 毫秒
1.
2.
Al_2O_3Cu-Ti-Zr/Nb钎焊研究 总被引:3,自引:0,他引:3
使用Cu Ti Zr钎料对Al2 O3 Nb进行了钎焊试验。通过扫描电镜、能谱、X射线衍射分析了界面形貌、元素分布 ,并对反应相进行了判定。Cu70 Ti2 5 Zr5 钎料在 12 93K、10min条件下界面产生了 3种新相 :Cu2 Ti4O、Ti固溶体、CuTi,界面结构为Al2 O3 Cu2 Ti4O Ti固溶体 CuTi Cu固溶体 +CuTi。采用拉剪试验评定了强度 ,结果证实12 93K、10min ,使用Cu70 Ti2 5 Zr5 钎料的接头强度最高达到 16 2MPa ,增加或减少Ti的质量分数以及改变保温时间都会使接头抗剪强度下降。 相似文献
3.
Al2O3/Cu-Ti-Zr/Nb钎焊研究 总被引:5,自引:0,他引:5
使用Cu-Ti-Zr钎料对Al2O3/Nb进行了钎焊试验。通过扫描电镜、能谱、X射线衍射分析了界面形貌、元素分布,并对反应相进行了判定。Cu70Ti25Zr5钎料在1293K、10min条件下界面产生了3种新相Cu2Ti4O、Ti固溶体、CuTi,界面结构为Al2O3/Cu2Ti4O/Ti固溶体/CuTi/Cu固溶体+CuTi。采用拉剪试验评定了强度,结果证实1293K、10min,使用Cu70Ti25Zr5钎料的接头强度最高达到162MPa,增加或减少Ti的质量分数以及改变保温时间都会使接头抗剪强度下降。 相似文献
4.
5.
6.
钛合金窄间隙TIG焊技术研究 总被引:1,自引:0,他引:1
在介绍窄间隙焊接的优越性和钛合金各种焊接方法的基础上,着重介绍了俄罗斯中央结构材料研究院研制出的一种应用于钛合金的窄间隙TIG焊接技术,并分析了该技术的优缺点、工艺特性及此工艺下的啮合强化效应,分析并讨论了产生此强化效应的原因。 相似文献
7.
8.
Double cantilever beam (DCB) specimens were used to research the stress corrosion cracking of T225NG titanium alloy in loop water of high temperature and high pressure. DCB specimens were forced pre-stress, put into high pressure ataoclave , and the stress corrosion and crack expansion of specimens were observed and measured in 500 h, 1 000 h and 2000 h respectively. The results show that small expansion occurred along the direction of pre-cracking. According to calculation, the speed of cracking expansion is lower than 10 -9 m/s in 500 h and the value of K ISCC /KI is higher than 0. 75, which proves that T225NG has an excellent corrosion resistance in loop water. The main reason is that there is an oxide film on the surface of specimens. According to the analysis of energy dispersive spectroscopy (EDS) and X-ray diffraction ( XRD ) , the oxide film consists of TiO2. Therefore, the oxide film at the crack tip impedes the hydrogen separating out from the cathode to penetrate into titanium alloy and resists hydrogen embrittlement. 相似文献
9.
研究了Ti-75合金的配用焊丝的成分,焊接接头和焊缝金属的力学性能、断裂力学性能、应力腐蚀与均匀腐蚀性能以及做了模拟结构件的焊接试验。结果表明,所研制的焊丝成分选择合理,焊接接头综合性能良好,是比较理想的配用焊丝填料。 相似文献
10.