Modulation of electrical transport in calcium cobaltite ceramics and thick films through microstructure control and doping

Ca₃Co₄O₉ is a promising p-type thermoelectric oxide material having intrinsically low thermal conductivity. With low cost and opportunities for automatic large scale production, thick film technologies offer considerable potential for a new generation of micro-sized thermoelectric coolers or generators. Here, based on the chemical composition optimized by traditional solid state reaction for bulk samples, we present a viable approach to modulating the electrical transport properties of screen-printed calcium cobaltite thick films through control of the microstructural evolution by optimized heat-treatment. XRD and TEM analysis confirmed the formation of high-quality calcium cobaltite grains. By creating 2.0 at% cobalt deficiency in Ca_2.7Bi_0.3Co₄O_9+δ, the pressureless sintered ceramics reached the highest power factor of 98.0 μWm^?1 K^-2 at 823 K, through enhancement of electrical conductivity by reduction of poorly conducting secondary phases. Subsequently, textured thick films of Ca_2.7Bi_0.3Co_3.92O_9+δ were efficiently tailored by controlling the sintering temperature and holding time. Optimized Ca_2.7Bi_0.3Co_3.92O_9+δ thick films sintered at 1203 K for 8 h exhibited the maximum power factor of 55.5 μWm^?1 K^-2 at 673 K through microstructure control.     

25%小偏置碰撞策略及测试评估研究

随着汽车事故的增加,且小重叠碰撞事故死亡率居高不下,小偏置碰撞试验逐渐成为焦点。基于IIHS公布的最新车辆碰撞试验结果,统计超过100余款不同类型的25%小偏置碰撞车辆,建立碰撞转角与碰撞区域的数学模型,将25%小偏置碰撞归结为三种不同的碰撞策略,分别是吸能策略、掠过策略和掠过与吸能策略;并进行试验验证,对三种策略的优缺点进行分析。结果表明,小偏置碰撞试验可运用合理的碰撞策略达到法规要求,对25%小偏置碰撞试验具有一定的参考价值。     

Synergistic effect of bulk phase doping and layered-spinel structure formation on improving electrochemical performance of Li-Rich cathode material

In this study, La was doped into the lithium layer of Li-rich cathode material and formed a layered-spinel hetero-structure. The morphology, crystal structure, element valence and kinetics of lithium ion migration were studied by field emission scanning electron microscope (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The La doped lithium-rich cathode material exhibited similar initial discharge capacity of 262.8 mAh g^?1 at 0.1 C compared with the undoped material, but the discharge capacity retention rate can be obviously improved to 90% after 50 cycles at 1.0 C. Besides that, much better rate capability and Li⁺ diffusion coefficient were observed. The results revealed that La doping not only stabilized the material structure and reduced the Li/Ni mixing degree, but also induced the generation of spinel phase to provide three-dimensional diffusion channels for lithium ion migration. Moreover, the porous structure of the doped samples also contributed to the remarkable excellent electrochemical performance. All of these factors combined to significantly improve the electrochemical performance of the material.     

Phase and microstructure evolution of Sc2O3–CeO2 –ZrO2ceramics in Na2SO4 + V2O5 molten salts

In this study, the destabilization resistance of Sc₂O₃ and CeO₂ co-stabilized ZrO₂ (SCZ) ceramics was tested in Na₂SO₄ + V₂O₅ molten salts at 750°C–1100 °C. The phase structure and microstructure evolution of the samples during the hot corrosion testing were analyzed with X-ray diffraction (XRD), Raman spectra, scanning electron microscopy (SEM), energy dispersive X-ray spectrum (EDS), and X-ray photoelectron spectroscopy (XPS). Results showed that the destabilization of SCZ ceramics at 750 °C was the result of the chemical reaction with V₂O₅ to produce m-ZrO₂ and CeVO₄, and little ScVO₄ was detected in the Sc₂O₃-rich SCZ ceramics. The primary corrosion products at 900 °C and 1100 °C were CeO₂ and m-ZrO₂ due to the mineralization effect. The Sc₂O₃-rich SCZ ceramics exhibited excellent degradation resistance and phase stability owing to the enhanced bond strength and the decreased size misfit between Zr⁴⁺ and Sc³⁺. The destabilization mechanism of SCZ ceramic under hot corrosion was also discussed.     

一种大量元素水溶肥料的制备及其在玉米上的喷施效果

根据玉米需肥特性设计氮磷钾比例,制备了含中微量元素的大量元素水溶肥料,产品氮、磷、钾比例为2∶1∶4,属于高钾中氮低磷型.在河北省安平县前子文村和浙江省新昌县孟家塘村玉米上开展了叶面喷施试验.结果表明:玉米生物学性能得到改善,玉米产量、出籽率、百粒重与容重得到提高;与空白对照相比,平均增产率为5.45％,平均纯增收896.40元/公顷,平均产投比为5.43∶1.     

Auto-registration of medium and high spatial resolution satellite images by integrating improved SIFT and spatial consistency constraints

Feature-based methods have been developed in the past decades for the registration of optical satellite images. However, it is still a challenging problem to handle well the registration between medium and high spatial resolution images due to the large difference of the spatial structural features and local details for the same objects. In this study, an automated co-registration technique is proposed that integrates an improved SIFT (I-SIFT) and a novel matching strategy called spatial consistency constraints (SCC) to cope with the large difference in spatial resolutions between the image pair. Three constraints on angle, distance, and ratio are introduced to re the initial matching features obtained by I-SIFT. Three groups of experiments were conducted to validate the effectiveness of the proposed method. The experiments used high resolution multispectral and panoramic SPOT 5/6 images and Landsat 5/8 orthorectification images. Experimental results show that the registration error lies in about 1 pixel of high-resolution images and demonstrate that the proposed I-SIFT-SCC approach is suitable for fine registration of optical satellite images from medium spatial resolution to high spatial resolution with resolution ratio up to 6.     

ZY6400/23/47型掩护式液压支架偏置改造

铁煤集团大兴矿(以下简称"大兴矿")2019年产240万t,井田位于铁法煤田的西南角,火成岩侵入及地质构造复杂,煤层破坏程度严重[1-2]。受火成岩影响,煤层瓦斯含量大幅增加[3-4],渗透性能差,力学强度低,煤的含水率低,自然发火期较短,是煤与瓦斯突出矿井。在采煤过程中,防治自然发火是重中之重,综采设备在设计初期未考虑实施灭火的操作空间,为此,笔者提出通过改造综采设备增加实施灭火的操作空间,降低出现自然发火灾害时防治的难度,保证采煤安全。     

Increasing Volumetric CO2 Uptake of Hypercrosslinked Polymers through Composite Formation

To overcome the drawbacks of solid microporous materials for CO₂ capture, this proof‐of‐concept study demonstrates a low‐cost and rapid method for producing composites consisting of hypercrosslinked polymers (HCP) with a polyethyleneimine (PEI) binder. The resulting materials capture CO₂ through physical and chemical absorption simultaneously. Compared with HCP, the composites exhibit higher CO₂ uptake, higher volumetric density, and improved tolerance to water which is attributed to the PEI binder.     

Removal of imidacloprid and acetamiprid from tea infusions by microfiltration membrane

Removal of imidacloprid and acetamiprid in tea infusions by microfiltration membrane using dead‐end model was investigated in the present study. The results showed that microfiltration significantly promoted the removal of both pesticides (P < 0.05) in tea infusions. Furthermore, the extent of removal was strongly influenced by the pore size of membrane, operational pressure and the concentrations of tea infusions. The initial concentration of imidacloprid and acetamiprid showed no significant effect on their removal rates. The maximum removal rates were 79.7% for imidacloprid and 81.9% acetamiprid. The changes in major chemical components of tea infusions after microfiltration were evaluated. The results indicated that microfiltration caused no considerable changes in total polyphenols and total free amino acids, and small but statistically significant losses (6.3–18.0%) of eight catechins and three methylxanthines when filtration volume reached to 200 mL. The present study validated the application of microfiltration as a potentially feasible and promising method for the removal of imidacloprid and acetamiprid residues from tea infusions.     

Recent progress of the gas diffusion layer in proton exchange membrane fuel cells: Material and structure designs of microporous layer

Proton exchange membrane fuel cells (PEMFCs) have become the most attractive power supply units for stationary and mobile applications. The operation, design characteristics, as well as performance of PEMFCs, are closely related to the multiphase transport of mass, heat, and electricity in the cell, a critical of which is the gas diffusion layer (GDL). It is very important to guarantee the transmission of water and gasses under high current density, and which is the weakness of PEMFCs at present. Microporous layer (MPL) is considered to be the key variable for mass transfer, so varieties of works focus on modification of MPL materials and its structure design. However, there is still a lack of special review to summarize and prospect the progress of MPL in recent years. This review article therefore focuses on the insights and comprehensive understanding of four critical issues of the MPL, the porosity, pore size distribution, wettability, structural design and the durability of MPL. At last, the conclusion and recommendations section summarized the future prospects and recommendations for possible research opportunities.