基于感知评价的Internet语音终端流量控制

分析了影响因特网语音通信质量的主要因素，根据实时传输控制协议计算延迟、丢包率等网络参数，并利用RBF神经网络将参数映射为语音质量评分，根据评分值的变化动态地调整语音终端的编码速率，在保证一定语音质量的同时，缓解网络拥塞。实验证明了该方法的有效性。     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

HPMBP与伯胺N_(1923)对希土元素(Ⅲ)的协同萃取

本文研究了HPMBP与伯胺N_(1923)的二甲苯溶液,从盐酸介质中协同萃取希土(Ⅲ)的机理。用斜率法、恒摩尔法确定了协萃配合物的组成为:RNH_3Ln(PMBP)_4。求得关于Pr(Ⅲ)协萃反应的平衡常数及协萃配合物的生成常数分别为:logK_(12)=-1.95;logβ_(12)=3.94。实验发现,协萃系数(R)随希土元素的原子序数(Z)递变而呈现“双峰效应”。还研究了协萃配合物的IR,NMR谱。     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

8Li次级束的产生

在北京串列加速器次级束流线上通过2 H(7Li,8Li) 1H逆运动学反应产生了用于核天体物理研究的8Li次级束。准直后的次级束纯度达到 80 %以上 ,对于 44MeV的7Li强度约为 3 0s- 1·pnA- 1,可以用来进行逆几何转移反应的实验测量。     

网络化制造中基于STEP-NC的编程方法

STEP-NC是由欧美提出的新的数控接口标准，目的是取代旧的数控标准ISO6983。本文首先分析了STEP-NC的两种应用标准：ISO14649（ARM）和STEPAP238（AIM），并且分析了Part21和Part28的应用领域及Part21文件格式和其中的信息产生方法。然後介绍了ST-Developer环境下ROSEC＋＋颠库编程接口及其应用程序的早、晚编联方式，并且以此为基础设计了整个程序的编程流程，重点介绍了工艺规划设计。最后给出了在C＋＋编程环境下利用ROSE库函数写入形成STEP AP238文件的方法。     

Trace elements in particles of motor vehicle exhaust in Shanghai

A nuclear microprobe with high spatial resolution and high analytical sensitivity was applied to analyze trace elements,especially lead,in vehicle exhaust of Shanghai city.The result shows that the chemical composition and its corresponding x-ray relative intensity are different among different vehicle exhausts.There are many kinds of metal elements in particles of vehicle exhaust.most are harmful to people,such as Ti,Cr,Mn,Pb,etc.We found that the lead concentration was 6820μg/g and the bromine concentration was 5300μg/g in the exhaust from Santana using leaded gasoline(SULG).which is higher than any other kinds of vehicle exhausts.We have also detected the minimum lead in the particles of unleaded gasoline and its content varies from one to another.Its mean concentration was 450μg/g and the highest reached 6210μg/g.The unleaded gasoline‘s Pb existed in the whole particle while the leaded gasoline‘s enriched in the surface of the particle and was more harmful to the human beings.     

Structure and composition of guanidine acrylate, guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride

Structures and compositions of the monomers guanidine acrylate and guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride enriched in acrylate comonomer units were determined. It was shown that ampholytic copolymers, owing to their ionic nature, contained comonomeric guanidine acrylate or methacrylate units and diallyldimethylammonium chloride units, as well as the acrylate comonomer with the diallyl counterion and polymeric acrylate and diallyl ion pairs. It follows from IR and ¹H NMR data that guanidine methacrylate has the same structure (with two hydrogen bonds) in the solid state and in solutions. Guanidine acrylate structures in the solid state and in dimethylsulfoxide are identical and analogous to guanidine methacrylate structure in this solvent. In water, the guanidine acrylate structure has another type of hydrogen bonding (with one hydrogen bond, where the proton is shifted toward the guanidine group). These features of hydrogen bonding of guanidine acrylate and guanidine methacrylate are also retained in their homopolymers and copolymers with diallyldimethylammonium chloride. It was shown that the thermal stability of the copolymers was higher than that of their homopolymers, confirming the formation of intramolecular ion pairs of oppositely charged units of ampholytic copolymers. Moreover, the thermal stability of guanidine methacrylate-diallyldimethylammonium chloride copolymers is higher than that of guanidine acrylate-diallyldimethylammonium chloride copolymers.