Effect of Temperature and Strain Rate on the Hot Deformation Behaviour of Ferritic Stainless Steel

Metals and Materials International - The flow behaviour and microstructure characteristics of a ferritic stainless steel were investigated using plain strain compression test on a Gleeble 3500...     

Densification mechanism during reactive hot pressing of B4C-ZrO2 mixtures

The densification behaviors of pure B₄C and B₄C-ZrO₂ mixtures were compared during hot pressing. The results showed that in-situ formed ZrB₂ effectively enhanced the densification process of B₄C-ZrO₂ mixtures, more significantly during the intermediate stage. Within the relative density ranging from 0.75 to 0.90, the B₄C-15?wt%ZrO₂ mixture (B15Z) achieved the maximum densification rate as twice much as that of pure B₄C. The stress exponent n>3 indicated plastic deformation was the dominant densification mechanism of B15Z. The viscosities of plastic flow were evaluated using Murray-Rodger-William equation and the viscosity of B15Z was only a quarter of that in pure B₄C. The sintering activation energy was calculated to be 305.9?kJ/mol for pure B₄C and 197?kJ/mol for B15Z, respectively. It was proposed that the lower viscosity of plastic flow and activation energy accelerated the sliding and propagating motions of plastic flow, by which underlain the enhanced densification behaviors of B₄C-ZrO₂ mixtures.     

Microstructures and mechanical properties of B4C-TiB2-SiC composites fabricated by ball milling and hot pressing

B₄C-TiB₂-SiC composites were fabricated via hot pressing using ball milled B₄C, TiB₂, and SiC powder mixtures as the starting materials. The impact of ball milling on the densification behaviors, mechanical properties, and microstructures of the ceramic composites were investigated. The results showed that the refinement of the powder mixtures and the removal of the oxide impurities played an important role in the improvement of densification and properties. Moreover, the formation of the liquid phases during the sintering was deemed beneficial for densification. The typical values of relative density, hardness, bending strength, and fracture toughness of the composites reached 99.20%, 32.84?GPa, 858?MPa and 8.21?MPa?m^1/2, respectively. Crack deflection, crack bridging, crack branching, and microcracking were considered to be the potential toughening mechanisms in the composites. Furthermore, numerous nano-sized intergranular/intragranular phases and twin structures were observed in the B₄C-TiB₂-SiC composite.     

Fetus-in-fetu with malignant recurrence

Fetus-in-fetu is an unusual condition in which a vertebrate fetus is enclosed within the abdomen of another fetus. These occurrences are usually benign. This report describes an instance of malignant recurrence after resection of a fetus-in-fetu.     

离散事件动态系统的代数模型及其控制器的分析计算

本文在离散事件动态系统的Ｐｅｔｒｉ网图形描述的基础上建立了相应的代数模型，该模型可以用来计算无竞争无回路Ｐｅｔｒｉ网的“最大状态”；该“最大状态”的计算在本文给出的动态反馈控制器中得到了应用。     

金刚石薄膜制备和评价

采用平直钨丝作热解源,并借助钨丝支架的弹性恢复力,较好地解决了热丝热解化学气相沉积法(HFCVD)合成金刚石过程中热解丝的变形问题.样品独立加热,基片温度、钨丝温度、钨丝与样品基片距离均可独立调节.装置改进后,在Si(100)上合成了面积大约45mm×25mm的比较均匀的金刚石膜.用扫描电子显微镜(SEM)、Raman光谱和X射线衍射仪对制备的金刚石膜进行了分析.     

Diagnosis of hemostasis disorders in young children using turbidimetry

Practical application of turbidimetrical method for the diagnosis of haemostasis disorders in babies with acute intestinal infections (AII) is described. The results of plasma biochemical analysis show that disturbances in balance between coagulation and fibrinolytic systems takes place in patients with this pathology. The correlation between biochemical parameters and clinical characteristics is observed. As follows from our data, the phase of the haemostasis disorders in babies with AII does not depend on etiology of the disease, but indicates its severity.