Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

Phosphorus‐containing polyaryloxydiphenylsilanes with high flame retardance arising from a phosphorus–silicon synergistic effect

Polyaryloxydiphenylsilanes were prepared from phosphorus‐containing diols and diphenydichlorolsilane through solution polymerization. With a stoichiometric imbalance in feed monomers, the resulting polymers exhibited moderate melting points and good processing properties. The polymers prepared showed initial decomposition temperatures above 340 °C, excellent thermal stability, high char yields at 850 °C and very high limited oxygen index values of 56–59. The polymers' char yields and their (P + Si) contents showed linear relationships. © 2003 Society of Chemical Industry     

一次盐水设备运行总结

介绍了内蒙古海吉氯碱化工股份有限公司6万t/a离子膜烧碱装置一次盐水设备的运行情况和运行过程中存在的问题及相应的技改措施.     

基于网络环境的计算机资料室工作

随着信息技术的迅速发展,基于网络的信息资源共享已成为信息化社会的基本特征。数字化图书馆和电子期刊网的出现,正在改变着人们的阅读习惯,丰富的信息资源和跨时空的浏览方式彻底颠覆了传统的图书馆、资料室的服务模式。同时,数字化图书馆也给资料室管理模式创新带来了新的契机。分析了院系资料室面临的挑战与机遇,探讨了新形势下计算机资料室工作,提出了利用信息技术,改革服务方式,拓展服务内容,提高服务水平,提供有特色的专业服务。     

建筑电气设计中AutoCAD二次开发的研究

基于AutoCAD的二次开发环境下,建立幻灯片库,在AutoCAD本身所包含的程序帮助下,将已建好的幻灯片库嵌入到AutoCAD用户专用下拉菜单中.给设计者创造属于自己的开发环境,使AutoCAD在建筑电气设计中的使用更加灵活,极大的提高设计效率.     

SU-8 3D microoptic components fabricated by inclined UV lithography in water

Out-of-plane microlenses and microoptical fiber holder are two of the most important components for building an integrated microoptic system with a precise alignment accuracy. In this paper, a simple and convenient method to fabricate these components from SU-8 by using inclined UV lithography in water is proposed. It consists of two perpendicular exposures in SU-8 at ±45°. DI water possesses a low absorption coefficient and a moderate and stable value of refractive index in near UV. Using water, the exposure angle in SU-8 can be increased to 50° from 35° in air necessary to pattern the desired 45° slope of the sidewalls. The principle of the proposed technique and the detailed fabrication process of the microoptic components will be presented. The integratability of the fabricated components was demonstrated by the fabrication of the microoptical fiber holder with a pre-aligned out-of-plane microlens.