Structural Response of Nuclear Containment Shield Buildings with Construction Openings

Steam generator replacement at nuclear power plants requires large construction openings in nuclear containment structures. This study examines the effects of such openings placed in a 61?cm (2?ft) thick dome of a shield building. The dome is cast in two layers, and the limiting cases of the two layers acting as one and the lower layer carrying the entire load are considered. Without openings, the stresses due to dead load in the structure are very low when compared to the material strength. With openings, the loads are easily redistributed around the opening, and the maximum stresses for the conservative case are between three and four and one-half times larger than in the original structure with no openings. The extent of the affected area around the holes is relatively small. Smooth corners in the openings are necessary to avoid high local stress concentrations.     

Honeymoon with IWBs: A qualitative insight in primary students' views on instruction with interactive whiteboard

The main purpose of this study was to investigate the views of primary students about interactive whiteboard [IWB] use in their classes from attitudinal and pedagogical perspectives. Research was designed as an empirical approach to phenomenology. Data was collected from fifty primary students (fourth to eighth) through focus group interviews. Nvivo 9 qualitative data analysis software was used to analyze data. Results showed that students like instruction with IWB especially for such reasons/capabilities as practical and economical use, better visual presentation, and test-based use. Students were predominantly uncomfortable with the technical problems. They believed that instruction with IWB positively impacted their learning especially because of visualization and contextualization, effective presentation, test-based use, and motivational factors. Finally it was inferred that IWBs were not used to their full potential, and both technical problems and common practices indicated that teachers were still at an initial stage of transmission to instruction with IWB and they needed both technical and pedagogical training.     

An online optimum voltage estimation and real‐time MPP tracking for a PV system

In this paper, a photovoltaic system topology incorporating a new maximum power point tracking (MPPT) controller method is presented. This method uses an autotuning estimator and a PI controller to make the system work in the maximum power point. The controller is formulated based on the bijectivity in the photovoltaic generator characteristic; therefore, if the optimal voltage is reached, this means that the maximum of power is obtained. The proposed MPPT algorithm is implemented on a dSpace DS1104 controller board. In order to demonstrate the efficiency of the proposed algorithm in real time, an experimental setup using a boost converter connected to a resistive load is successfully implemented and studied. The obtained experimental results prove the validity of the proposed MPPT algorithm.     

Influence of temperature gradient and growth rate on the mechanical properties of directionally solidified Sn–3.5 wt% Ag eutectic solder

The Sn–3.5 wt% Ag eutectic alloy was directionally solidified upward with a constant growth rate (V = 16.5 μm/s) at different temperature gradients (G = 1.43–4.28 K/mm) and with a constant temperature gradient (G = 3.93 K/mm) at different growth rates (V = 8.3–500 μm/s) in a Bridgman-type directional solidification furnace. The rod spacings (longitudinal section, λ _L and transverse section, λ _T ) and mechanical properties (microhardness, HV and ultimate tensile strength, σ _UTS ) of Sn–3.5 wt% Ag eutectic alloy were measured. The dependency of the microhardness, ultimate tensile strength on the temperature gradient, growth rate and rod spacings were determined. According to experimental results, the microhardness and ultimate tensile strength of the solidified samples increase with increasing G and V, but decrease with the increasing the rod spacing.     

An empirical analysis of petroleum demand for Indonesia: An application of the cointegration approach

This paper uses selection criteria from various models in a bounds testing approach to cointegration to estimate the price and income elasticities of demand for total petroleum products (gasoline and diesel) and gasoline share in total products in Indonesia. The results suggest that both total products and gasoline share estimates are more responsive to changes in income than changes in the real price of petroleum products. These results have important policy implications as they suggest that policy makers may need to use market-based pricing policies and other policies such as public enlightenment in addition to regulations like minimum energy efficiency standards to promote efficiency and conservation and curb the rising consumption of petroleum products in Indonesia.     

Investigation of microhardness and thermo-electrical properties in the Sn–Cu hypereutectic alloy

Sn–3 wt% Cu hypereutectic alloy was directionally solidified upward with different growth rates (2.24–133.33 μm/s) at a constant temperature gradient (4.24 K/mm) and with different temperature gradients (4.24–8.09 K/mm) at a constant growth rate (7.64 μm/s) in the Bridgman-type growth apparatus. The measurements of microhardness of directionally solidified samples were obtained by using a microhardness test device. The dependence of microhardness HV on the growth rate (V) and temperature gradient (G) were analyzed. According to these results, it has been found that with the increasing the values of V and G the value of HV increases. Variations of electrical resistivity (ρ) and electrical conductivity (σ) for casting samples with the temperature in the range of 300–500 K were also measured by using a standard dc four-point probe technique. The variation of Lorenz coefficient with the temperature for Sn–3 wt% Cu hypereutectic alloy was determined by using the measured values of electrical and thermal conductivities. The enthalpy of fusion for same alloy was determined by means of differential scanning calorimeter from heating trace during the transformation from eutectic liquid to eutectic solid.     

Electricity demand for South Korean residential sector

This study estimates the electricity demand function for the residential sector of South Korea with the aim of examining the effects of improved energy efficiency, structural factors and household lifestyles on electricity consumption. In the study, time series data for the period from 1973 to 2007 is used in a structural time series model to estimate the long-term price and income elasticities and annual growth of underlying energy demand trend (UEDT) at the end of the estimation period. The result shows a long-term income elasticity of 1.33 and a long-term price elasticity of −0.27% with −0.93% as the percentage growth of UEDT at the end of the estimation period. This result suggests that, in order to encourage energy efficiency in the residential sector, the government should complement the market based pricing policies with non-market policies such as minimum energy efficiency standards and public enlightenment.     

Dynamic behavior of a two-stage gear train used in a fixed-speed wind turbine

The dynamic behavior of a two stage spur gear system used in a typical wind turbine is investigated in this paper. With the purpose of having an accurate simulation, for a given excitations, of the dynamic response of bearings, shafts and teeth in contact.In this study, we developed a lamped mass dynamic model with 12 DOFs. This model is excited by external and internal issues sources. The main factors of these excitations are the variability in the wind resource and the time varying mesh stiffness fluctuation.The aerodynamic torque is calculated from an empirical approach of the power coefficient. The incoming flow is modeled by an analytic equation test varies with time. The differential equations governing the system motion are solved by an implicit Newmark algorithm.