Feasibility analysis of membrane reactors – discovery of reactive arheotropes

A feasibility analysis methodology adopted from reactive distillation is applied to membrane reactors. A model is formulated to depict the reactive liquid phase composition on the retentate side of a continuous type membrane reactor. The effects of both the chemical reaction kinetics and the membrane mass transfer kinetics on the feasible products are elucidated by means of retentate phase diagrams and bifurcation analysis. The proposed method can be applied to various membrane processes, independent of the specific structure of the membrane. Two quaternary reaction systems are considered to illustrate the methodology. In the first hypothetical system, it is shown how selective membranes can influence the sequence of effective volatilities which in turn affects the feasible products of the system. In the second example of practical importance, i.e. the heterogeneously catalysed synthesis of propyl acetate coupled with permeation through a porous polycarbonate membrane, the dusty gas model is applied to describe the component fluxes through the membrane. For the latter reaction system, the existence of reactive arheotrope is demonstrated. Arheotropes represent mass transfer controlled feasible products of membrane separation process.     

瞿秋白论广州暴动及其领袖张太雷

瞿秋白生前曾经多次评述过广州暴动,他为此留下10数篇著述,成为有关广州暴动的一份权威性的历史文献,其理性的思考具有重要的学术理论研究价值.文章以瞿秋白对广州暴动的认知、论述为视角,力求再现彼时彼境中瞿秋白笔下的广州暴动及其领袖张太雷.     

用于实时数据传输的滑动帧方法及其实现

根据某雷达系统对测量信号的快速传输要求,提出采用滑动帧的处理方法并在FPGA中实现,克服了传统帧处理难以满足快速传输要求的不足。阐述了滑动帧结构的构造思想,详述了滑动帧结构的特点及具体功能模块的实现。根据实际应用需求构造了滑动帧结构处理器,试验和应用结果表明设计可行有效,能充分满足实时数据传输的要求。     

基于作业测定技术的后桥壳生产线工艺评价及优化

以某企业后桥壳生产线为研究对象,运用作业测定技术中的时间研究法,测定后桥壳各工序的标准时间,评价工艺及找到瓶颈工序;运用"5W1H"提问技术,根据"ECRS"原则,同时结合工艺设计及企业资源情况,对后桥壳生产线现有工艺进行评价及优化,改善后,使生产线的产能每天提高了10件,生产能力提高了33.57%.     

镁钴铝类水滑石催化合成安息香甲醚

采用共沉淀法制备了镁钴铝类水滑石化合物(MgCoAl-HTLcs),并用 X 射线衍射、扫描电子显微镜、NH_3程序升温脱附等方法对 MgCoAl-HTLcs 进行了表征,并以 MgCoAl-HTLcs 为催化剂催化苯甲醛与甲醇反应合成安息香甲醚,研究了n(Mg):n(Co):n(Al)、催化剂用量、原料配比、反应温度、反应时间对合成反应的影响。表征结果显示,MgCoAl-HTLcs 的晶相完整,表面主要为弱酸、弱碱性。催化合成安息香甲醚的适宜条件为:MgCoAl-HTLcs 催化剂用量0.10 g(约为原料总质量的0.23%),n(Mg):n(Co):n(Al)=0.4:1.6:1.0,V(苯甲醛):V(甲醇)=3:50,反应温度50℃,反应时间150 min。在此条件下,苯甲醛的平衡转化率达77.49%,安息香甲醚选择性接近100%。为洁净合成安息香甲醚开辟了一条新的途径。     

New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

Detection of failure sites by focused ion beam and nano-probing in the interconnect of three-dimensional stacked circuit structures

Focused ion beam (FIB) and nano-probing were applied for failure analysis of three-dimensional stacked circuits with copper through-silicon-vias between the stacked chips. The failure analysis was done after high temperature storage and thermal cycling tests. Passive voltage contrast in FIB allowed to pinpoint the open sites. FIB cross-sections showed the presence of opens at the bottom of the copper vias. The failure cause was suspected to be an interlayer particle, which was confirmed by optical profilometry. Nano-probing was used on another sample to pinpoint the failure location through the measurement of the local resistance within the daisy chains. The failure was traced out to be related with surface contamination.     

复合聚全氟乙丙烯材料的介电及高频击穿性能研究

在聚全氟乙丙烯(FEP)中添加 TiO_2和 Al_2O_3,通过热压成型的方法制备了 FEP/TiO_2复合材料和 FEP/Al_2O_3复合材料,研究了氧化物添加量对复合材料介电常数、介电损耗和高频击穿性能的影响。结果表明,随氧化物含量的增加,复合材料的介电常数和介电损耗均增加;在同一添加量下,TiO_2对复合体系的介电性能影响较大。FEP/TiO_2复合材料的高频击穿性能随 TiO_2含量的增加而下降,在 TiO_2含量为4.0%(质量分数,下同)时,复合材料的损伤阈值已降为 FEP 材料损伤阈值的48.9 %。而 FEP/Al_2O_3复合材料的高频击穿性能随 Al_2O_3含量的增加而升高,当 Al_2O_3含量为1.2%时,复合材料的损伤阈值已增大到 FEP 材料损伤阈值的2倍,达到313 J/m~2。