中空激光光内送粉熔池温度控制研究

在激光增材制造过程中,熔池温度的稳定性是表征加工过程稳定性的一个重要指标.设计一套控制熔池温度的闭环反馈系统,以达到控制熔池温度,提高成形件质量.基于C#编程软件实现了温度信号的传递,采用PID控制算法设计了温度控制器.实验结果表明,此系统能实时、准确地实现熔池温度的闭环控制,能够有效消除直壁墙熔覆过程中因热累积而造成的“蘑菇云”现象,且成形件几何精度有显著提高,各处显微组织差异较小,组织致密均匀.     

Mechanical Properties of Single-Layer Diamond Reinforced Poly(vinyl alcohol) Nanocomposites through Atomistic Simulation

Low-dimensional carbon nanostructures are ideal nanofillers to reinforce the mechanical performance of polymer nanocomposites due to their excellent mechanical properties. Through molecular dynamics simulations, the mechanical performance of poly(vinyl alchohol) (PVA) nanocomposites reinforced with a single-layer diamond – diamane is investigated. It is found the PVA/diamane exhibits similar interfacial strengths and pull-out characteristics with the PVA/bilayer-graphene counterpart. Specifically, when the nanofiller is fully embedded in the nanocomposite, it is unable to deform simultaneously with the PVA matrix due to the weak interfacial load transfer efficiency, thus the enhancement effect is not significant. In comparison, diamane can effectively promote the tensile properties of the nanocomposite when it has a laminated structure as it deforms simultaneously with the matrix. With this configuration, the interlayer sp³ bonds endows diamane with a much higher resistance under compression and shear tests, thus the nanocomposite can reach very high compressive and shear stress. Overall, enhancement on the mechanical interlocking at the interface as triggered by surface functionalization is only effective for the fully embedded nanofiller. This work provides a fundamental understanding of the mechanical properties of PVA nanocomposites reinforced by diamane, which can shed lights on the design and preparation of next generation high-performance nanocomposites.     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

Improving the initialization speed for long-range NRTK in network solution mode

Initialization speed is one of the most important factors in network real time kinematic (NRTK) performance. Owing to the low correlation among the error s     

Ni-Foam Structured Ni-Phyllosilicate Ensemble as an Efficient Monolithic Catalyst for CO2 Methanation

This work proposed a new path to synthesize Ni-phyllosilicate through the reaction of nickel hydroxide and silica sol on the surface of Ni-foam to form the monolithic Ni-phyllosilicate/Ni-foam catalyst. Ni-phyllosilicate could reprint the morphology of nickel hydroxid and firmly anchor on the framework of Ni-foam, which obtained fine Ni particles of 2.8 nm after reduction in H₂ at 650 °C, resulting in high catalytic activity for CO₂ methanation. In addition, the Ni-phyllosilicate/Ni-foam catalyst showed high long-term stability in a 100 h-lifetime test owing to the combined effects of surface confinement of Ni-phyllosilicate, firm anchoring between Ni-phyllosilicate and Ni-foam, as well as the high heat transfer property of Ni-foam.

Graphical Abstract

     

Two-step method to deposit ZrO2 coating on carbon fiber: Preparation,characterization, and performance in SiC composites

Recently, ceramic matrix composites reinforced by short carbon fibers (CFs) attracted increasing attentions. To further improve mechanical properties and oxidation resistances, CFs were subjected to oxidation and acidification followed by sol-gel dip-coating to deposit ZrO₂ on their surfaces. ZrO₂-C_f/SiC composites were fabricated by joint hot compression molding and sintering, compared to C_f/SiC and SiC prepared by the same method. Microstructural analyses indicated that ZrO₂ coatings were successfully deposited on CF surfaces, formed strong bonding and interfaces between CF and the matrix. Meanwhile, CFs were found uniformly distributed in SiC matrix with random orientations. Flexural curves of ZrO₂-C_f/SiC and C_f/SiC revealed the presence of “false plasticity” regions after sharp drops, which were quite different from brittle flexural behavior of SiC ceramic. Compression strength of the three samples showed step-up growth. ZrO₂-C_f/SiC exhibited the highest value, indicating the introduction of CFs and ZrO₂ coatings do have great influence on mechanical performances. After heat treatment, ZrO₂-C_f/SiC exhibited better oxidation resistance than C_f/SiC, with weight loss ratios estimated to ??3.76% and ??6.43%, respectively. These improved properties indicated that ZrO₂-C_f/SiC would be excellent alternatives to other existence materials under ultra-high temperature environments.     

焉耆盆地原油物理化学特征及油源对比研究

在焉耆盆地侏罗系三工河组和八道湾组均发现原油,目前关于侏罗系产层原油的油源问题存在不同的认识。对研究区原油的物理、化学性质进行系统的研究,认为侏罗系三工河组和八道湾组原油不仅在物理性质上有一定的差别,而且在地球化学组成及生物标记化合物上也有一定的差异,应具有不同的来源。侏罗系三工河组原油属于典型腐殖型干酪根成因,而侏罗系八道湾组原油除了具有腐殖型干酪根成因的某些特征外,还具有湖相泥岩生烃的特点。通过原油与各类源岩生物标志物进一步对比分析发现,侏罗系三工河组原油与西山窑、三工河组烃源岩及石炭系、三叠系烃源岩地球化学特征均存在明显差异,与侏罗系八道湾组烃源岩对比性较好。侏罗系八道湾组原油与八道湾组、三叠系源岩有一定相似性,因此认为八道湾组源岩为其主要源岩,三叠系源岩也有一定的贡献。目前勘探生产主要以八道湾组烃源岩为目标,下一步应加强对三叠系烃源岩贡献区带的勘探部署。      

钢塔架设计探讨

根据石油天然气工业中排气筒和火炬设计的特点，为了更好、更准确进行塔架设计。介绍了塔架设计中塔架结构几何尺寸和杆件截面的初选方法和经验数据；塔架结构受风荷载整体计算时体型系数的探讨；塔架基础在软土地基或基岩特殊条件下的处理方法。     

石化装置仪表控制系统供电的可靠性设计

介绍了仪表控制系统的供电原则及仪表控制系统的负荷分配方案。包括冗余供电仪表控制系统的电源配置、冗余型24VDC电源装置的电源配置、非冗余供电的控制系统及仪表的电源配置方案。