吸湿凉爽机织物的结构设计与性能

为研究织物组织结构与复合纱线线密度对织物凉爽性能的影响,将线密度为7.4和9.8 tex涤纶分别与线密度为7.8 tex锦纶反向加捻、并线后作为纬纱,以8.3 tex涤纶/竹浆纤维50/50混纺纱作经纱,设计平纹、二上一下斜纹和透孔组织织物.测试织物的瞬间接触凉感、热湿舒适性能及织物干、湿态升温曲线,并采用凉爽温度指数对织物的综合凉爽性能进行评价.研究结果表明:6种设计织物的瞬间接触凉感均高于标准,且平纹织物最好,纬纱粗细对瞬间接触凉感影响不显著;透孔织物透气性最好,且在人体出汗的状态下具有较好的导湿散热性能.平纹织物凉爽温度指数最高,最大凉爽温度为2.8℃,综合凉爽性能最好.     

A novel InP/InGaAs TEBT for ultralow current operations

A novel InP/InGaAs tunneling emitter bipolar transistor (TEBT) is fabricated and demonstrated. The studied device exhibits a very small collector-emitter offset voltage of 40 mV and an extremely wide operation regime. The operation region is larger than 11 decades in magnitude of collector current (10/sup -12/ to 10/sup -1/A). A current gain of 3 is obtained even if the device is operated at an ultralow collector current of 3.9 /spl times/ 10/sup -12/A (1.56 /spl times/ 10/sup -7/A/cm/sup 2/). Furthermore, the common-emitter breakdown voltage of the studied device is higher than 2 V. Consequently, the studied device shows a promise for low supply voltage, and low-power consumption circuit applications.     

Interaction of triton X-100 on silica: A relationship between surface characteristics and adsorption isotherms

Adsorption of Triton X-100 on various silica substrates has been investigated. A number of solids, including a natural quartz, this quartz washed with HCl acid and subsequently heated at 1273 K; two aerosils and one Kieselgel silicas were studied. These solids exhibit surface areas in the range of 5 to 430 m² g^?1. All the Triton adsorption isotherms display an S-shape at the adsorption temperatures studied (298 and 308 K). It has been found that the pretreatments of natural quartz (by water washing, impurities removed by acid and/or high temperature calcination) affect considerably the amounts of TX-100 adsorbed. Measurements of surface composition have been made by X-ray photoelectron spectroscopy (XPS) with particular emphasis on the presence of impurities and on the number of OH groups at the surface of the samples. The nature of the surface hydroxyl has also been studied by infrared spectroscopy. Furthermore, the specific number of hydroxyl groups on the surface of the silica samples has been determined by thermogravimetric analysis. Finally an attempt to correlate solid surface characteristics with adsorption isotherms has been developed.     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

A general framework for debugging

The state of the art of debugging is examined. A debugged process model that serves as the basis of a general debugging framework is described. The relationship of the model to traditional debugging processes and support tools is discussed. A minimal set of requirements for a general debugging framework is described in terms of both the theory behind debugging methodologies and the support tools. An execution monitor, Eden, that serves as a debugging tool within this general framework is described     

Online and Offline Rotary Regression Analysis of Torque Estimator for Switched Reluctance Motor Drives

A new torque estimator for switched reluctance motor (SRM) drives based on 2-D rotary regression analysis is presented in this paper. The proposed torque estimator is composed of a bicubic regressive polynomial as a function of rotor position and input current. The regressive coefficients can be computed offline or online from the torque characteristics acquired either experimentally or from numerical computation. Furthermore, a torque estimation method by taking mutual coupling into consideration is proposed. It can be seen that the estimated and experimentally obtained self-coupling and mutual-coupling torque characteristics are in good agreement with each other. In addition, the dynamic torque waveforms with and without the mutual coupling, estimated by the proposed estimator, are found to be virtually the same as those obtained from the bicubic spline interpolation for SRM drives with single-pulse voltage, hysteresis current chopping, as well as with voltage pulse width modulation control. The success of all the case studies being reported is a good validation of the usefulness and accuracy of the proposed real-time torque estimator that, as described in this paper, can be used to quickly estimate the instantaneous output torque of SRM drives.     

Enhanced electron emission from phosphorus-doped diamond-cladsilicon field emitter arrays

Undoped and phosphorus (P)-doped diamond-clad Si field emitter arrays have been successfully fabricated using microwave plasma chemical vapor deposition (MPCVD) technology. The electron emission from the blunt diamond-clad microtips are much higher than those for the pure Si tips with sharp curvature due to a lower work function. Furthermore, the characteristics of emission current against applied voltage for the P-doped diamond-clad tips show superior emission at lower field to the undoped ones. After the examination of Auger electron spectroscopy (AES) and electrical characteristics of as-grown diamond, such a significant enhancement of the electron emission from the P-doped diamond-clad tips is attributed to a higher electron conductivity and defect densities     

Developing maintainable expert systems using case-based reasoning

Abstract: Maintainability problems associated with traditional software systems are exacerbated in rule-based systems. The very nature of that approach — separation of control knowledge and data-driven execution — hampers maintenance. While there are widely accepted techniques for maintaining conventional software, the same is not true for rule-based systems. In most situations, both a knowledge engineer and a domain expert are necessary to update the rules of a rule-based system. This paper presents, first, an overview of the software engineering techniques and object-oriented methods used in maintaining rule-based systems. It then discusses alternate paradigms for expert system development. The benefits of using case-based reasoning (from the maintenance point of view) are illustrated through the implementation of a case-based scheduler. The main value of the scheduler is that its knowledge base can be modified by the expert without the assistance of a knowledge engineer. Since changes in application requirements can be given directly to the system by the expert, the effort of maintaining the knowledge base is greatly reduced.     

Bioactivity of antifouling paints based on organotin toxicants

This paper discusses the bioactivity of antifouling paints based on organotin toxicants, such as tributyltin fluoride (TBTF) and triphenyltin fluoride (TPTF). These compounds were used alone or mixed as the main toxicant in formulations. The use of TPTF or mixtures of TPTF and TBTF, with vinyl binders, led to paints with satisfactory bioactivity during a 24 months immersion period. With the same binders, TBTF alone provided only 12 months of antifouling protection. The correlation coefficients calculated from the fouling attachment values and the rosin content in the binder showed that the bioactivity of the tested formulations depended on the solubility of the toxicant in sea water and on the composition and solubility of the binders.