X70配套埋弧焊丝用H08D盘条的研制

介绍了北营公司X70配套埋弧焊丝用H08D盘条的开发研制情况.其生产工艺的关键点为:转炉采用“双渣法除磷”,脱氧合金化在转炉和LF炉两个阶段完成,连铸采用结晶器电磁搅拌及末端电磁搅拌、恒定拉速;盘条采用控冷控轧及轧后延迟型斯太尔摩冷却工艺等措施.生产的成品盘条成分、力学性能、金相组织等指标均满足客户拉拔工艺要求.     

海上稠油油田蒸汽吞吐产量确定新方法

针对目前蒸汽吞吐产量预测模型假设条件简单、普适性差等问题,一般采用测试法和类比法综合确定海上稠油油田蒸汽吞吐初期产量。由于目前海上油田通常只开展常规测试,无法直接获得热采开发初期产量。笔者提出海上稠油油田蒸汽吞吐初期产量确定新方法,建立蒸汽吞吐相对于常规开发的初期产量倍数预测模型,通过蒸汽吞吐产量倍数,将常规测试确定的产量转化为蒸汽吞吐产量。研究表明,蒸汽吞吐初期产量倍数主要受储集层渗透率、原油黏度、注入强度、蒸汽干度等因素影响,利用正交试验设计和多元回归等方法,建立海上稠油油田蒸汽吞吐初期产量倍数与油藏地质参数及注入参数之间的非线性预测模型,该模型经实际生产数据验证,预测误差小于5%,可靠性高,能够为海上稠油油田蒸汽吞吐初期产量的确定提供依据。     

Uplink Scheduling in CDMA Packet-Data Systems

Uplink scheduling in wireless systems is gaining importance due to arising uplink intensive data services (ftp, image uploads etc.), which could be hampered by the currently in-built asymmetry in favor of the downlink. In this work, we propose and study algorithms for efficient uplink packet-data scheduling in a CDMA cell. The algorithms attempt to maximize system throughput under transmit power limitations on the mobiles assuming instantaneous knowledge of user queues and channels. However no channel statistics or traffic characterization is necessary. Apart from increasing throughput, the algorithms also improve fairness of service among users, hence reducing chances of buffer overflows for poorly located users. The major observation arising from our analysis is that it is advantageous on the uplink to schedule “strong” users one-at-a-time, and “weak” users in larger groups. This contrasts with the downlink where one-at-a-time transmission for all users has shown to be the preferred mode in much previous work. Based on the optimal schedules, we propose less complex and more practical approximate methods, both of which offer significant performance improvement compared to one-at-a-time transmission, and the widely acclaimed Proportional Fair (PF) algorithm, in simulations. When queue content cannot be fed back, we propose a simple modification of PF, Uplink PF (UPF), that offers similar improvement. Hereafter, we refer to users with low recieved power at the base even when transmitting at peak transmit power as “weak” users, and the strongly recieved users at the base as “strong” users. Krishnan Kumaran is currently a member of the Complex Systems Modeling section in the Corporate Strategic Research of ExxonMobil Corp., Clinton, NJ. Formerly, he was a Member of Technical Staff in the Mathematics of Networks and Systems Research Department at Bell Labs in Murray Hill, NJ, where his research interests were in modeling, analysis and simulation of design, resource management and scheduling issues in telecommunication networks. Lijun Qian is an assistant professor in the Department of Electrical Engineering at Prairie View A&M University. He received his B.S. from Tsinghua University in Beijing, M.S. from Technion-Israel Institute of Technology, and Ph.D. from WINLAB, Rutgers University, all in electrical engineering. Before joining PVAMU, he was a researcher at Networks and Systems Research Department of Bell Labs in Murray Hill, NJ. His major research interests are in wireless communications and networking technologies, especially in radio resource management, protocol design, TCP/RLP optimization and MPLS traffic engineering.     

Cu-Mg/Al_2O_3催化乙醇和乙二胺合成N-乙基乙二胺

在固定床反应器内,乙醇和乙二胺经分子间催化胺化反应合成了N-乙基乙二胺(NEED),考察了一系列铜系催化剂的活性,并筛选出催化性能较好的Cu-Mg/A l2O3催化剂;通过X射线衍射和透射扫描电子显微镜方法表征了助剂Mg对Cu/A l2O3催化剂的改性作用;考察了助催化剂Mg含量、反应温度、反应压力、进料量和乙二胺含量等对Cu-Mg/A l2O3催化剂性能的影响。实验结果表明,Cu-Mg/A l2O3催化剂具有很好的活性和选择性;在200℃、3.0MPa、质量分数20%的乙二胺乙醇溶液、进料量1.0mL/m in的条件下,乙二胺的转化率为71.56%,产物NEED的选择性和收率分别为92.62%和69.86%;经过20 d的连续使用表明,Cu-Mg/A l2O3催化剂具有良好的稳定性。     

结构化编程实现Sniffer

随着各高校校园网络规模的不断扩大和各种应用的急剧增加,各种新的网络问题也在不断出现。Sniffer是网络管理员进行网络管理的有效工具,可以有效地对网络进行实时监控,及时发现网络中存在的各种问题。本文首先介绍了Sniffer的工作原理,其次给出了实现Sniffer功能的编程流程图,并用C语言给出了编程所需的关键代码。     

采用区内C／I平衡的多区峰窝CDMA系统下行链路的性能

本文对采用区内Ｃ／Ｉ平衡的多区蜂窝ＣＤＭＡ系统下行链路的性能进行分析，给出两种区内Ｃ／Ｉ平衡算法并比较它们的性能，考虑呈对数正态分布的阴影和Ｒ＾－４规律的路径损失的综合影响，采用与传统不同的小区平均中断概率来评价系统的性能。     

A mechanism for transgranular stress-corrosion cracking

A model is proposed to explain transgranular-stress corrosion cracking (T-SCC) in face-centered cubic (fcc) materials. Crack propagation is shown to be anisotropic, in that growth near {110} < 001> is discontinuous due to crack arrest by dislocation blunting whereas growth away from this growth orientation is continuous. For the former case, renucleation of arrested cracks involves active dissolution of shear bands at the crack tip, which changes the stress state at Lomer-Cottrell locks, causing them to fail by cleavage. Once the crack is nucleated, its instantaneous macroscopic crack-growth velocity is considered to be comprised of multiple nucleation of microcracks with intervening arrests. This microcracking results from the interaction of the stress fields from neighboring cracks which are forming simultaneously, the crack-opening constraint due to ligaments which act as “bridges” behind the crack front, and the localized dissolution at the microcrack tip which affectsK _IC and leads to the “cobblestone” appearance. Experimental evidence and theoretical considerations are presented to support the model. The system studied was Cu-25 at. pct Au in 0.6 M NaCl solution at potentials between 300 and 400 mV (sce), which precludes hydrogen embrittlement. This article is based on a presentation made in the symposium “Quasi-Brittle Fracture” presented during the TMS fall meeting, Cincinnati, OH, October 21–24, 1991, under the auspices of the TMS Mechanical Metallurgy Committee and the ASM/MSD Flow and Fracture Committee.     

用JHS-3胶合砂防粉细砂

针对孤东油田大量油井出现粉细砂甚至粘土砂而严重影响生产的问题,研制了用JHS-3胶合砂防粉细砂方法。介绍了胶合砂的基本配方、主要技术指标及防砂机理。适应性分析结果表明,施工井的层数、处理半径和施工压力升幅3个因素直接影响着胶合砂的防砂堵水效果。现场20井次的应用情况可看出,胶合砂能有效地防住粉细砂和粘土砂,明显地改善产液剖面,并有显著的降水增油效果。     

电潜泵中压变频调速系统的改进

电潜泵中压变频器输出端产生高次谐波和脉冲电流 ,对电潜泵电动机的绝缘性能和轴承寿命造成不利影响。为此 ,提出 3项改进对策 :①采用谐振软性开关逆变电路 ,使功率开关器件在零电压条件下导通 ;②在变频器逆变输出端设置电抗滤波器抑制高次谐波电流 ;③改变电动机内部结构 ,如加大定子槽宽 ,增加转子导条尺寸 ,变星接法为星 角接法 ,采用绝缘轴承等。实践证明 ,采取改进对策后 ,不仅提高了电潜泵的产量 ,而且变频器滤波后电动机端的过电压明显减小 ,电潜泵和电缆的寿命延长