The effect of alkali metal oxide on the properties of borosilicate fireproof glass: Structure,thermal properties,viscosity, chemical stability

The purpose of the current work was to research the effect of alkali metal oxide on the structure, thermal properties, viscosity and chemical stability in the glass system (R₂O–CaO–B₂O₃–SiO₂) systematically. Because the glass would emulsify when Li₂O was added to the glass batch, this article did not discuss Li₂O. The results showed that when the amount of Na₂O was less than 4 mol.%, there was a higher interconnectivity of borate and silicate sub-networks in glass, as more mixed Si–O–B bonds were present in glass. The glass samples exhibited excellent thermal properties and chemical stabilities. As the amount of Na₂O exceeded 4 mol.%, the interconnectivity of borate and silicate sub-networks was weakened. The thermal properties and chemical stabilities of the glass samples were reduced. The connectivity of the silicate sub-network was weakened slightly as the Na/K ratio varied, and the coefficient of thermal expansion (CTE) of the glass samples gradually increased, and the resistance to thermal shock (RTS) value gradually decreased. Moreover, the viscosity of the glass samples decreased with the ratio of Na/Si and Na/K increased.     

多孔SiO2分子巢制备多功能涤纶纤维试验研究

针对传统PET材料不具备抗菌、不耐洗等问题,以煎煮法为基础,以草珊瑚、艾叶和薄荷为原料,制备含植物活性成分的溶液,其具有抗菌、杀菌的作用;以溶胶-凝胶法为多孔材料制备方法,用十六烷基三甲基溴化铵、十二烷基苯磺酸钠表面活性剂为模板剂,正硅酸乙酯为有机硅源,氨水为催化剂,乙醇和乙醚为助溶剂,在水-乙醇-乙醚体系中合成多孔二氧化硅微球;然后,多孔二氧化硅微球与提取液混合制备含植物活性成分的多孔二氧化硅分子巢;最后以制备的多孔二氧化硅分子巢与普通的聚酯切片用熔融纺丝工艺进行造粒、纺丝,得到具有抗菌、杀菌和耐洗的多功能涤纶纤维.通过SEM微观观察和力学性能测试、抗菌试验、耐洗性测试,对上述制备的多功能涤纶纤维性能进行验证.结果表明:在模板剂总浓度为0.029 mol·L-1、V醇:V醚=20:20、两种表面活性剂比为4:1时,得到的多孔SiO2微球排列规整;当多孔二氧化硅分子巢掺量(质量分数)在0.5％～1％时,通过熔融共混纺丝得到的新型多功能涤纶纤维力学性能表现最优;当多孔二氧化硅分子巢掺量(质量分数)在1％时,得到的新型多功能涤纶纤维的抗菌性能达到87.9％.而二氧化硅分子巢掺量越高,纤维材料越耐洗.以上结果说明本试验制备涤纶纤维的方案可行.     

Feasibility study of large-scale mass customization 3D printing framework system with a case study on Nanjing Happy Valley East Gate

At present, the development and implementation of digital transformation are the keys to promoting high-quality industry development. The new digital fabrication method of robotic 3D printing is a research area being studied by many to tackle the issue of the declining productivity of traditional construction methods. Although many studies have been done, most of the current 3D printing projects are facing limitations in terms of scale. In order to bridge the gap, this article proposed a mass customization 3D printing framework system for large-scale projects. This article discusses how mass customization is made possible through the joint operation of the FUROBOT software and 3D printing hardware. By taking the east gate of Nanjing Happy Valley Plaza as a case study, the article demonstrates and studies the feasibility of the large-scale mass customization 3D printing framework system.     

中药桂枝总黄酮的提取工艺研究

优化桂枝总黄酮的提取工艺，建立桂枝的提取和含量测定方法。通过单因素试验，考察提取方法、提取溶剂浓度、提取体积、提取时间对药材总黄酮含量的影响，采用正交试验，优化提取工艺条件，筛选出桂枝总黄酮的最佳提取工艺。总黄酮最佳提取工艺为75%乙醇、料液比1:40、回流提取时间60 min。该方法能有效测定桂枝药材总黄酮的含量，为该药材的质量标准研究提供一定的科学依据。本方法重复性较好、方法稳定、可行。     

高等级生物安全实验室通风空调系统冗余设计原则探讨

对比分析了国内外标准有关高等级生物安全实验室通风空调系统冗余设计的要求。结合我国已有高等级生物安全实验室,重点分析了送风机、排风机、排风高效过滤器冗余设计的具体实施形式和存在的问题,给出了冗余设计原则建议。     

Nanomaterials for radiotherapeutics-based multimodal synergistic cancer therapy

Over the past decade, numerous studies have attempted to enhance the effectiveness of radiotherapy (external beam radiotherapy and internal radioisotope therapy) for cancer treatment. However, the low radiation absorption coefficient and radiation resistance of tumors remain major critical challenges for radiotherapy in the clinic. With the development of nanomedicine, nanomaterials in combination with radiotherapy offer the possibility to improve the efficiency of radiotherapy in tumors. Nanomaterials act not only as radiosensitizers to enhance radiation energy, but also as nanocarriers to deliver therapeutic units in combating radiation resistance. In this review, we discuss opportunities for a synergistic cancer therapy by combining radiotherapy based on nanomaterials designed for chemotherapy, photodynamic therapy, photothermal therapy, gas therapy, genetic therapy, and immunotherapy. We highlight how nanomaterials can be utilized to amplify antitumor radiation responses and describe cooperative enhancement interactions among these synergistic therapies. Moreover, the potential challenges and future prospects of radio-based nanomedicine to maximize their synergistic efficiency for cancer treatment are identified.

     

A practical reliability assessment approach and its application for pile-stabilized slopes using FORM and support vector machine

Bulletin of Engineering Geology and the Environment - Many uncertainties exist in pile-stabilized slopes which make their design substantially complicated. In this paper, a first-order reliability...