Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

Cholesterol‐imprinted polymer receptor prepared by a hybrid imprinting method

A novel cholesterol‐imprinted polymer (CMIP‐H) was prepared by a hybrid method of covalent imprinting and non‐covalent imprinting. This approach involves the copolymerization of a template‐containing monomer, cholesteryl 2‐hydroxyethyl methacrylate carbonate, and a cross‐linker, followed by hydrolysis to afford a flexible guest‐binding site accompanied with the easy and efficient removal of a ‘sacrificial spacer’. The effect of solvent on the binding capacity of CMIP‐H towards cholesterol was studied, indicating that a good binding capacity towards cholesterol could be achieved in a less‐polar solvent. The binding experiments of CMIP‐H towards a series of structural analogues of cholesterol, including cholesterol acetate, progesterone and stigmasterol, were carried out in hexane. The results showed that CMIP‐H almost did not bind cholesterol acetate at all because the hydrogen‐bonding site is blocked. It exhibited a similar binding towards both cholesterol and stigmasterol, but much higher binding towards progesterone. Copyright © 2005 Society of Chemical Industry     

β－C_2S固溶体稳定的热力学研究

从热力学理论出发，利用Ｘ射线衍射定性和定量的方法，对β－Ｃ＿２Ｓ固溶体的稳定性进行了分析和研究。经热力学理论推导得出β－Ｃ＿２Ｓ稳定的热力学条件，即掺入的微量元素的化学位μ＿ｉ须小于β－Ｃ＿２Ｓ的反应自由焓△Ｇ＿β，μ＿ｉ＜△Ｇ＿β．并定量地计算出一种微量元素稳定β－Ｃ＿２Ｓ的临界掺加量为；多种微量元素对β－Ｃ＿２Ｓ的稳定性判断条件为：     

语音时域分割研究

在语音时域挑选剩余可懂度低的可用置换集合,置换集合是语音TDS系统中不可缺少的重要环节,本文给出了可用置换选取的条件、客观评价标准和方法。     

Mobility modeling, location tracking, and trajectory prediction inwireless ATM networks

Wireless ATM networks require efficient mobility management to cope with frequent mobile handoff and rerouting of connections. Although much attention has been given in the literature to network architecture design to support wide-area mobility in public ATM networks, little has been done to the important issue of user mobility estimation and prediction to improve the connection reliability and bandwidth efficiency of the underlying system architecture. This paper treats the problem by developing a hierarchical user mobility model that closely represents the movement behavior of a mobile user, and that, when used with appropriate pattern matching and Kalman filtering techniques, yields an accurate location prediction algorithm, HLP, or hierarchical location prediction, which provides necessary information for advance resource reservation and advance optimal route establishment in wireless ATM networks     

单光子时间分辨在线谱仪系统中的接口电路

本文介绍单光子时间分辨在线谱仪系统中的多道分析器与IBM PC/XT微型计算机接口的工作原理及控制程序。     

石油系油浆与煤系闪蒸油的焦化性能——I．热解条件的影响

通过偏光显微镜观察了石油系油浆（LH）与煤系闪蒸油（SN）焦化后所得焦块的光学结构。结果表明，在较宽条件下两种原料单独焦化均得不到取向度高的流线型结构。将两种原料以一定比例混合后先热解丙焦化所得焦块的光学结构明显好于二者混合后直接焦化所得焦块的光学结构，其中LH和SN以3：2的重量比混合后在440℃、1MPa下热解3．5h然后再在530℃、1MPa下焦化8h所得焦块为具有较高取向度的流线型结构，适合于作为针状焦的起始原料。     

Ultrasonic thin-walled tube wave structure for sensing devices

Theoretical and experimental investigations of thin-walled tube acoustic wave devices for gravimetric sensing applications are presented. Integrated sensor configurations have been demonstrated by employing a sol-gel processed thin piezoelectric lead zirconate titanate (PZT) film. This was coated coaxially on stainless steel tubes and interdigital transducers (IDT) fabricated as the transmitter and receiver on the curved tube surfaces. We have observed tube waves along both the axial and circumferential directions between 1 and 6.6 MHz. We have also analyzed the mass sensitivities of different modes propagating along the tubes and shown that high mass sensitivity can be achieved by keeping the tube wall thin     

Cast bulk ZrTiAlCuNi amorphous alloys

Cylindrical bulk amorphous samples with diameters up to 10 mm have been prepared by casting ZrTiAlCuNi alloys in a copper mould. In order to rank glass-forming ability as a function of alloy composition, alloys were also cast into wedge-shaped moulds; to a first approximation, the thickness of the amorphous region obtained can be taken as an indication of glass-forming ability. The compositions which lead to the production of bulk glasses all have reduced glass transition temperatures in excess of 0.65 and the extremely high glass-forming ability of these compositions is discussed. We suggest that both the Al and Ti contents are determining factors for the production of bulk amorphous samples and these are believed to reduce the driving force for, and hence the rate of, crystallisation. These amorphous alloys have been found to display high thermal stability and can be annealed for several minutes in the supercooled liquid region. They are ductile at room temperature and have a high value of yield stress.     

电位滴定法研究~(99)Tc-HMDP和~(99)Tc-HEDP中Tc的氧化态

~(99)Tc-HMDP和~(99)Tc-HEDP溶液是在相应的螫合剂存在下,用过量SnCl_2还原~(99)TcO_4-制得。用标准I_2液对SnCl_2进行了剩余量电位滴定,确定了在pH～3的介质中,~(99)Tc-HMDP和~(99)Tc-HE-DP中~(99)Tc的氧化态均为+4。全部实验在N_2气流中进行。~(99)Tc-HMDP和~(99)Tc-HEDP的紫外光谱表明:在用I_2滴定的过程中,~(99)Tc只处于一种氧化态+4;将它们放置在空气中,一小时后仍较稳定。