Feasibility study of large-scale mass customization 3D printing framework system with a case study on Nanjing Happy Valley East Gate

At present, the development and implementation of digital transformation are the keys to promoting high-quality industry development. The new digital fabrication method of robotic 3D printing is a research area being studied by many to tackle the issue of the declining productivity of traditional construction methods. Although many studies have been done, most of the current 3D printing projects are facing limitations in terms of scale. In order to bridge the gap, this article proposed a mass customization 3D printing framework system for large-scale projects. This article discusses how mass customization is made possible through the joint operation of the FUROBOT software and 3D printing hardware. By taking the east gate of Nanjing Happy Valley Plaza as a case study, the article demonstrates and studies the feasibility of the large-scale mass customization 3D printing framework system.     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。     

一种5 重real-time PCR筛查转基因水稻方法的建立

以转基因水稻中最常用的CaMV35S启动子、NOS终止子、Cry1Ab/Ac基因、HPT基因及SPS水稻内标基因为研究对象，利用5 种不同的荧光信号（FAM、HEX、Taxas Red、Cy5、Cy5.5）进行多重实时聚合酶链式反应（real-time polymerase chain reaction，real-time PCR）检测方法的研究。通过引物组合筛选、反应体系优化、特异性测试、灵敏度测试、适用性测试等一系列实验，建立了5 重real-time PCR方法，灵敏度可达0.032%。此方法具有灵敏度高、结果准确、通量大等优点，可实现水稻中转基因成分的快速、高效检测。     

Adsp-21060的主机接口在实时图像处理中的应用

简要介绍了数字信号处理器Adsp 2 10 6 0和大规模可编程逻辑器件EP1K5 0。详细讨论了Adsp 2 10 6 0的主机接口工作模式以及一个实时图像跟踪处理器的硬件组成原理 ,在这个系统中EP1K5 0充当了主机。调试结果表明 ,所提出的硬件结构设计思想工作效率高 ,完全能够胜任实时图像处理的实际需要。     

CMOS光接收机主放大器设计

利用CMOS工艺设计一种用于SDH STM 4速率级(622 Mb/s)光纤用户网的光接收机放大电路。此电路由输入/输出缓冲、主放大单元、偏置补偿电路4部分组成。通过直接耦合技术提高增益,降低功耗;利用有源电感负载提高系统带宽。采用商用SmartSpice电路仿真软件和CSMC HJ 0.6μm工艺参数对该电路进行仿真。结果表明,该电路在5 V工作电压下中频增益为81 dB,3 dB带宽为470 MHz。     

基于ARM微处理器的故障记录系统

给出了在普通数据采集基础上的故障记录系统的设计方案,利用ARM微处理器实现了模拟信号较完整的故障波形记录和开关信号的事件顺序记录(SOE)。对LPC2106ARM系列处理器、ADS7871模/数转换器以及数据通信接口等内容进行了讨论,阐述了系统的工作原理、软件处理方式、系统通信。该设计方案电路简单,特别适用于电力系统。     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

基于FAX／40E电话语音／传真卡的通信技术研究

以一个基于 FAX/ 40 E电话语音 /传真卡技术的传真系统为例 ,重点研究 FAX/ 40 E电话语音 /传真卡技术与计算机之间的通信技术 ,并讨论有关多线程技术问题。     

Preparation of clean coal by flotation following ultra fine liberation

This paper reports the results of current fundamental research at the Department of Process Engineering, University of Miskolc on the processing of clean coal from Mecsek bituminous coal, Southern Hungary. The theoretical possibility of the separation of different petrographic components was proven experimentally and their liberation degree was determined based on the petrographic composition, flotation kinetic study of isolated components (groups of components), scanning electron microscopy and microprobe analyses. The mill with stirred ball media was chosen for the ultra-fine liberation of the coal components. It was revealed that along with the liberation of coal components, their surface oxidation and spontaneous agglomeration, entrapping the mineral impurities take place in ultra-fine grinding. This paper discusses the interfacial phenomena occurring in the ultra-fine grinding process and their influence on the flotation. The concept for the advanced preparation of clean coal was developed, tested and proved. The main steps of this concept are the ultra-fine liberation in the stirred-media mill, the de-agglomeration of flocs spontaneously formed during the ultra-fine grinding and the induced (hydrophobic) flocculation with the following two-step flotation in a flotation column.