智能建造技术协同创新主体互动关系研究

文章分析智能建造技术创新主体的特点，界定并划分智能建造技术协同创新主体互动关系的范畴和类别，建立智能建造协同创新的多方演化博弈模型，揭示智能建造技术协同创新主体互动关系。主要结论为：①智能建造技术协同创新呈现级联性、函数性、动态平衡性、不确定性和指数性特征；②智能建造技术协同创新主体互动关系分为同质性的内部主体互动和异质性的内部主体与外部主体互动，表现出利益共生、成长进化和共享协同的特征；③创新主体之间的互动行为有利于对创新资源进行有效配置，推动智能建造技术的应用。     

Novel TiC-based composites with enhanced mechanical properties

Novel TiC-based composites were synthesized by reactive hot-pressing at 1800 °C for 1 h with ZrB₂ addition as a sintering aid for the first time. The effects of ZrB₂ contents on the phase composition, microstructure evolution, and mechanical properties were reported. Based on the reaction and solid solution coupling effects between ZrB₂ and TiC, the product ZrC may be partially or completely dissolved into the TiC matrix, and then phase separation within the miscibility gap is observed to form lamellar nanostructured ZrC-rich (Zr, Ti)C. The TiC-10 mol.% ZrB₂ (starting batch composition) exhibits good comprehensive mechanical properties of hardness 27.7 ± 1.3 GPa, flexural strength 659 ± 48 MPa, and fracture toughness of 6.5 ± 0.6 MPa m^1/2, respectively, which reach or exceed most TiC-based composites using ceramics as sintering aids in the previous reports.     

自然循环窄矩形通道内过冷沸腾两相摩擦阻力特性

采用去离子水作为实验工质，在低压低流速自然循环工况下开展了单面加热可视化窄矩形通道内的过冷沸腾摩擦阻力特性实验研究。实验中测量了实验段内的压降数据，并通过高速摄影仪拍摄了窄矩形通道内的气液两相图像，提出了过冷沸腾条件下的两相摩擦压降的剥离计算方法。基于本实验中获得摩擦压降数据，对分别基于均相流模型和分液相模型的经典两相摩擦压降计算关系式进行了评估，实验结果表明：采用不同等效黏度计算方法的均相流模型计算结果比实验值明显偏小；而分相流模型中，Sun and Mishiba关系式和Tran关系式均能够较好地预测摩擦阻力，计算值与实验值的平均相对偏差在±15%以内。结合实验数据，以分相流模型方法为基础，考虑全液相Reynolds数、Martinelli参数和Laplace数的影响，获得了计算分液相折算系数的经验关系式，与实验数据符合较好, 平均相对误差在10%范围内。     

Controlling Au electrode patterns for simultaneously monitoring electrical actuation and shape recovery in shape memory polymer

This paper presents an effective approach to achieve efficient electrical actuation and monitoring of shape recovery based on patterned Au electrodes on shape memory polymer (SMP). The electrically responsive shape recovery behavior was characterized and monitored by the evolution change in electrical resistance of patterned Au electrode. Both electrical actuation and temperature distribution in the SMP have been improved by optimizing the Au electrode patterns. The electrically actuated shape recovery behavior and temperature evolution during the actuation were monitored and characterized. The resistance changes could be used to detect beginning/finishing points of the shape recovery. Therefore, the Au electrode not only significantly enhances the electrical actuation performance to achieve a fast electrical actuation, but also enables the resistance signal to detect the free recovery process.     

Electrochemically deposited Fe2O3 nanorods on carbon nanofibers for free-standing anodes of lithium-ion batteries

Fe₂O₃ nanorod/carbon nanofiber (CNF) composites were prepared by the electrochemical deposition of Fe₂O₃ on a web of CNFs, which was then used as a free-standing anode. The conductive, three-dimensional structure of the CNF web allowed for the electrodeposition of the Fe₂O₃ nanorods, while its high conductivity made it possible to use the composite as a free-standing electrode in lithium-ion batteries. In addition, it was easy and cheap to fabricate by a simplification of a process of cell preparation. The nanorod-like Fe₂O₃ structures could only be electrodeposited on the CNFs; flake-like Fe₂O₃ was formed on flat conductive glass substrates. It can be attributed to the different growth mechanism of Fe₂O₃ on the CNFs because of the large number of reaction sites on the CNFs, differences in the precursor concentration and diffusivity within the CNF web. The formation of aggregates of the Fe₂O₃ particles on thicker CNFs also indicated that the CNFs had determined the Fe₂O₃ growth mechanism. The synthesised Fe₂O₃/CNF composite electrode exhibited stable rate capacities at different current densities. This suggested that CNF-based composite did not exhibit the intrinsic disadvantages of Fe₂O₃. Finally, carbon coatings were deposited on the Fe₂O₃/CNF composites to further improve their electronic conductivity and rate capability.     

A novel combination of precursor pyrolysis assisted sintering and rapid sintering for construction of multi-composition coatings to improve ablation resistance of SiOC ceramic modified carbon fiber needled felt preform composites

A double-layer coating composed of MoSi₂–SiO₂–SiC/ZrB₂–MoSi₂–SiC was designed and successfully constructed by a novel combination of precursor pyrolysis assisted sintering and rapid sintering to improve the ablation resistance of SiOC ceramic modified carbon fiber needled felt preform composites (CSs). The ZrB₂–MoSi₂–SiC inner layer coating was in relatively uniform distribution in the zone of 0–3 mm from the surface of CSs through the slurry/precursor infiltration in vacuum and SiOC precursor pyrolysis assisted sintering, which played a predominant role in improving oxidation and ablation resistance and maintaining the morphology of CSs. The MoSi₂–SiO₂–SiC outer layer coating was prepared by the spray and rapid sintering to further protect CSs from high-temperature oxidation. The ablation resistance of CSs coated with double-layer coating was evaluated by an oxygen-acetylene ablation test under the temperature of 1600–1800 °C with different ablation time of 1000 and 1500 s. The results revealed that the mass recession rates increased with the rise of ablation temperature and extension of ablation time, ranging from 0.47 g/(m²·s) to 0.98 g/(m²·s) at 1600–1800 °C for 1000 s and from 0.72 g/(m²·s) to 0.86 g/(m²·s) for 1000–1500 s at 1700 °C, while the linear recession rates showed negative values at 1700 °C due to the formation of oxides, such as SiO₂ and ZrO₂. The ablation mechanism of the double-layer coating was analyzed and found that a SiO₂–ZrO₂–Mo_4.8Si₃C_0.6 oxidation protection barrier would be formed during the ablation process to prevent the oxygen diffusion into the interior CSs, and this study provided a novel and effective way to fabricate high-temperature oxidation protective and ablation resistant coating.     

Effect of H2O2 concentration on electrochemical growth and properties of vertically oriented ZnO nanorods electrodeposited from chloride solutions

In this work, ZnO nanostructures are electrodeposited on a transparent conducting glass from chloride baths. The influence of H₂O₂ concentration on the electrochemical characteristics has been studied using cyclic voltammetry (CV) and chronoamperometry (CA) techniques. From the analysis of the current transients on the basis of the Scharifker–Hills model, it is found that nucleation mechanism is progressive with a typical three-dimensional (3D) nucleation and growth process; independently with the concentration of H₂O₂. However, the nucleation rate of the ZnO changes with the increase of H₂O₂ concentration. The Mott–Schottky measurements demonstrate an n-type semiconductor character for all samples with a carrier density varying between 5.14×10¹⁸ cm⁻³ and 1.47×10¹⁸ cm⁻³. Scanning electron microscopy (SEM) observations show arrays of vertically aligned ZnO nanorods (NRs) with good homogeneity. The X-ray diffraction (XRD) patterns show that the ZnO deposited crystallises according to a hexagonal Würtzite-type structure and with the c-axis perpendicular to the electrode surface. The directional growth along (002) crystallographic plane is very important for deposits obtained at 5 and 7 mM of H₂O₂. The high optical properties of the ZnO NRs with a low density of deep defects was checked by UV–vis transmittance analyses, the band gap energy of films varies between 3.23 and 3.31 eV with transparency around 80–90%.     

积分中值屈服准则解析厚板轧制椭圆速度场

为解决非线性Mises比塑性功率积分困难以及由此导致的轧制功率解析式难以获得的问题,本文通过建立并利用线性比塑性功率表达式对提出的椭圆速度场进行能量分析,得到了轧制力能参数的解析解.文中通过对变角度屈服函数求积分中值,构建了一个新的屈服准则,它是主应力分量的线性组合,在π平面上的轨迹是逼近Mises圆的等边非等角的十二边形,其基于Lode参数表达式的理论结果也与实验数据吻合较好.同时,根据厚板轧制时金属流动速度从入口到出口逐渐增大的特点,提出了水平速度分量满足椭圆方程的速度场,该速度场满足运动许可条件.通过相应的轧制能量分析,获得了基于线性屈服准则的内部变形功率以及基于应变矢量内积法上的摩擦功率与剪切功率.在此之上,通过泛函的极值变分导出了轧制力矩、轧制力以及应力状态系数的解析解,并与现场实测数据进行了对比,结果表明利用本文提出的屈服准则与速度场所建立的轧制力矩与轧制力模型与实测值吻合较好,其中轧制力误差小于5.3%,轧制力矩误差在6%左右.     

Effect of Ba nonstoichiometry on the phase composition,microstructure, chemical stability and electrical conductivity of BaxCe0.7Zr0.1Y0.1Yb0.1O3−δ (0.9≤x≤1.1) proton conductors

The perovskite proton conductors Ba_xCe_0.7Zr_0.1Y_0.1Yb_0.1O_3−δ (x=0.9, 0.94, 0.98, 1.0, 1.03, 1.06, and 1.1) have been successfully prepared by the conventional solid state reaction route. X-ray diffraction (XRD) patterns of the samples indicate that Ba_xCe_0.7Zr_0.1Y_0.1Yb_0.1O_3−δ (x≥1.0) samples possess a single phase orthorhombic structure, but a secondary phase (Y,Ce)O_2−δ exists in Ba_xCe_0.7Zr_0.1Y_0.1Yb_0.1O_3−δ (x<1.0) samples. SEM photographs show that the grain size of Ba_xCe_0.7Zr_0.1Y_0.1Yb_0.1O_3−δ increases and the porosity decreases with Ba²⁺ content varying from x=0.9 to 1.1. Because of ZnO addition as sintering aid, the sintering temperature of the samples reduces from 1550 °C to 1250 °C. The chemical stability of the samples against CO₂ decreases with the increase in Ba content from x=0.9 to 1.1. All the samples show a excellent stability against water vapor at 850 °C. The conductivities of the samples increase and the activation energies reduce with the increase in Ba content. The present results suggest that it is very important to control the stoichiometry of cations to obtain desired perovskite type high temperature proton conductors.     

Sub-surface stress measurement of cross welds in a dissimilar welded pressure vessel

Manufacturing process of pressure vessels used in high-temperature applications normally needs employing dissimilar metal welds (DMWs) between austenitic and ferritic steel. However, high amount of thermal stresses at the welds are induced due to differences in coefficient of thermal expansion between the types of steel. This study investigates the evaluation of welding residual stresses in a pressure vessel manufactured by DMW of 316 L stainless steel shell to A106 carbon steel caps as well as similar welding of stainless steel shells. By using longitudinal critically refracted (LCR) ultrasonic waves, the residual stresses are experimentally measured. The ultrasonic method is based on acoustoelasticity law by which the ultrasonic wave velocity could be connected to the material stress. By changing the frequency in which the ultrasonic transducers are working, the LCR waves are able to penetrate in various depths of the material in order to measure the sub-surface residual stresses. Hence, four main aspects are considered in this study: (I) stress evaluation of the DMW; (II) sub-surface stress measurement; (III) stress evaluation of longitudinal weld and (IV) stress measurement in cross weld. It is demonstrated that the residual stresses of the DMW pressure vessel could be comprehensively evaluated by using the LCR method.