Sealing behaviour of glass-based composites for oxygen transport membranes

In this study, seven different filler materials in different proportions were added to a Ba-Ca-Si glass matrix “H” to investigate new sealant with higher thermal expansion coefficient (CTE) value and good sealing performance for application in oxygen transport membrane (OTM). SrTi_0.75Fe_0.25O_3-δ (STF25) was used as an OTM, and the sealing partners were ferritic steel Aluchrom and pre-oxidized Aluchrom. Compatibility tests were carried out to investigate the feasibility of the composites. Higher CTE values were found in dilatometer tests on composite samples by adding 40 wt% Ag (HAg40) and 30 wt% Ni-Cr (HNC30). Gas-tightness measurements of sandwiched samples produced appropriate helium leakage rates in the range of 10^?6 mbar·l·s^?1. Sealing behaviour of sealants HAg40 and HNC30 were investigated by joining STF25 and as-delivered/pre-oxidized Aluchrom together. Scanning electron microscopy (SEM) on cross-sections of the joints revealed a homogeneous microstructure and good adherence of the glass sealants to support metals and STF25.     

Statistical Piezotronic Effect in Nanocrystal Bulk by Anisotropic Geometry Control

Utilizing inner-crystal piezoelectric polarization charges to control carrier transport across a metal-semiconductor or semiconductor–semiconductor interface, piezotronic effect has great potential applications in smart micro/nano-electromechanical system (MEMS/NEMS), human-machine interfacing, and nanorobotics. However, current research on piezotronics has mainly focused on systems with only one or rather limited interfaces. Here, the statistical piezotronic effect is reported in ZnO bulk composited of nanoplatelets, of which the strain/stress-induced piezo-potential at the crystals’ interfaces can effectively gate the electrical transport of ZnO bulk. It is a statistical phenomenon of piezotronic modification of large numbers of interfaces, and the crystal orientation of inner ZnO nanoplatelets strongly influence the transport property of ZnO bulk. With optimum preferred orientation of ZnO nanoplatelets, the bulk exhibits an increased conductivity with decreasing stress at a high pressure range of 200–400 MPa, which has not been observed previously in bulk. A maximum sensitivity of 1.149 µS m⁻¹ MPa⁻¹ and a corresponding gauge factor of 467–589 have been achieved. As a statistical phenomenon of many piezotronic interfaces modulation, the proposed statistical piezotronic effect extends the connotation of piezotronics and promotes its practical applications in intelligent sensing.     

铌硅基高温合金定向凝固铸造温度场模拟计算

以铌硅基高温合金定向凝固铸造过程为对象，通过实验测试和反求法确定了铌硅基高温合金和型壳的热物性参数，以及凝固过程各界面换热系数等边界条件；利用ProCAST软件对不同抽拉速率下铌硅基高温合金凝固过程温度场进行了模拟。结果表明，随着抽拉速率由5 mm·min?1增加到10 mm·min?1，固/液界面离液态金属锡表面的距离由12.1 mm下降到8.2 mm；平均糊状区宽度逐渐变窄，由11.5 mm减小到10.4 mm。针对抽拉速率为5 mm·min?1的实验结果表明，数值模拟结果与实际定向凝固实验获得的一次枝晶间距差异在6%以内，从一个方面验证了温度场模拟结果的正确性，相关结果可为铌硅基高温合金叶片定向凝固铸造参数的确定提供参考。      

Cathode plasma electrolytic deposition of Al2O3 coatings doped with SiC particles

Semiconductor particles doped Al₂O₃ coatings were prepared by cathode plasma electrolytic deposition in Al(NO₃)₃ electrolyte dispersed with SiC micro- and nano-particles (average particle sizes of 0.5–1.7?µm and 40?nm respectively). The effects of the concentrations and particle sizes of the SiC on the microstructures and tribological performances of the composite coatings were studied. In comparison with the case of dispersing with SiC microparticles, the dispersion of SiC nanoparticles in the coatings was more uniform. When the concentration of SiC nanoparticles was 5?g/L, the surface roughness of the composite coating was reduced by 63%, compared with that of the unmodified coating. Friction results demonstrated that the addition of 5?g/L SiC nanoparticles reduced the friction coefficient from 0.60 to 0.38 and decreased the wear volume under dry friction. The current density and bath voltage were measured to analyze the effects of SiC particles on the deposition process. The results showed that the SiC particles could alter the electrical behavior of the coatings during the deposition process, weaken the bombardment of the plasma, and improve the structures of the coatings.     

Fabrication and microwave absorption properties of magnetite nanoparticle–carbon nanotube–hollow carbon fiber composites

Absorbents with “tree-like” structures, which were composed of hollow porous carbon fibers (HPCFs) acting as “trunk” structures, carbon nanotubes (CNTs) as “branch” structures and magnetite (Fe₃O₄) nanoparticles playing the role of “fruit” structures were prepared by chemical vapor deposition technique and chemical reaction. Microwave reflection loss, permittivity and permeability of Fe₃O₄–CNTs–HPCFs composites were investigated in the frequency range of 2–18 GHz. It was proven that prepared absorbents possessed the excellent electromagnetic wave absorbing performances. The bandwidth with a reflection loss less than −15 dB covers a wide frequency range from 10.2 to 18 GHz with the thickness of 1.5–3.0 mm, and the minimum reflection loss is −50.9 dB at 14.03 GHz with a 2.5 mm thick sample layer. Microwave absorbing mechanism of the Fe₃O₄–CNTs–HPCFs composites is concluded as dielectric polarization and the synergetic interactions exist between Fe₃O₄ and CNTs–HPCFs.     

Alloying behavior and novel properties of CoCrFeNiMn high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

An equiatomic CoCrFeNiMn high-entropy alloy was synthesized by mechanical alloying (MA) and spark plasma sintering (SPS). During MA, a solid solution with refined microstructure of 10 nm which consists of a FCC phase and a BCC phase was formed. After SPS consolidation, only one FCC phase can be detected in the HEA bulks. The as-sintered bulks exhibit high compressive strength of 1987 MPa. An interesting magnetic transition associated with the structure coarsening and phase transformation was observed during SPS process.     

Preparation of Bi2Ti2O7/TiO2 nanocomposites and their photocatalytic performance under visible light irradiation

To improve visible-light-driven photocatalytic activity of TiO₂, the octahedral Bi₂Ti₂O₇ nanoparticles have been successfully supported on TiO₂ nanotubes (Bi₂Ti₂O₇/TiO₂) for the first time by a simple hydrothermal method. The structure and electro-optical property of the Bi₂Ti₂O₇/TiO₂ were characterized in detail. The obtained Bi₂Ti₂O₇/TiO₂ exhibited a markedly enhanced photocatalytic activity and good stability for degradation of organic pollutants under visible light. The study presents a new way to synthesize Bi₂Ti₂O₇/TiO₂ using TiO₂ nanotubes as both supporter and reactant.     

Preparation of a CeO2–ZrO2 based nano-composite with enhanced thermal stability by a novel chelating precipitation method

In this study, a chelating agent is introduced to prepare CeO₂–ZrO₂ nano-composite through a precipitation process. The physicochemical properties of the oxide precursors, nano composite materials are strongly dependent on the preparation method and whether a chelating agent is used. Adding an appropriate quantity of chelating agent SO₄²⁻ can facilitate thermal stability and phase structure uniformity of CeO₂–ZrO₂ mixed oxides. The calculation results showed that the Gibbs free energy of chelating complex of [ZrSO₄]²⁺ (ΔG = −127.2469 kJ/mol) is higher than the [Ce(III)SO₄]⁺ (ΔG = -29.8279 kJ/mol). The precipitation chemical potential of Zr⁴⁺ moves close to the precipitation chemical potential of Ce³⁺. The novel and low-cost chelating precipitation method can modify the homogeneity of the compounds at the atomic scale, which can offer a powerful opportunity for, and provide direction in, the design of materials with exceptional properties.     

Fabrication of BSCF-based mixed ionic-electronic conducting membrane by electrophoretic deposition for oxygen separation application

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-δ (BSCF), which exhibits a high mixed oxide ionic-electronic conduction, was used for the fabrication of an oxygen separation membrane. An asymmetric structure, which was a thin and dense BSCF membrane layer supported on a porous BSCF substrate, was fabricated by the electrophoretic deposition method (EPD). Porous BSCF supports were prepared by the uniaxial pressing method using a powder mixture with BSCF and starch as the pore-forming agent (0–50 wt.%). The sintering behaviors of the porous support and the thin layer were separately characterized by dilatometry to determine the co-fired temperature at which cracking did not occur. A crack-free and thin dense membrane layer, which had about a 15 μm thickness and >95% relative density, was obtained after optimizing the processes of EPD and sintering. The dense/porous interface was well-bonded and the oxygen permeation flux was 2.5 ml (STP) min⁻¹ cm^-2 at 850 °C.     

Sub-surface stress measurement of cross welds in a dissimilar welded pressure vessel

Manufacturing process of pressure vessels used in high-temperature applications normally needs employing dissimilar metal welds (DMWs) between austenitic and ferritic steel. However, high amount of thermal stresses at the welds are induced due to differences in coefficient of thermal expansion between the types of steel. This study investigates the evaluation of welding residual stresses in a pressure vessel manufactured by DMW of 316 L stainless steel shell to A106 carbon steel caps as well as similar welding of stainless steel shells. By using longitudinal critically refracted (LCR) ultrasonic waves, the residual stresses are experimentally measured. The ultrasonic method is based on acoustoelasticity law by which the ultrasonic wave velocity could be connected to the material stress. By changing the frequency in which the ultrasonic transducers are working, the LCR waves are able to penetrate in various depths of the material in order to measure the sub-surface residual stresses. Hence, four main aspects are considered in this study: (I) stress evaluation of the DMW; (II) sub-surface stress measurement; (III) stress evaluation of longitudinal weld and (IV) stress measurement in cross weld. It is demonstrated that the residual stresses of the DMW pressure vessel could be comprehensively evaluated by using the LCR method.